KaydedilenlerDerginizi ekleyin

Dergiler / Sigma Mühendislik ve Fen Bilimleri Dergisi / 2019 / Cilt: 37 - Sayı: 3

NUMERICAL ANALYSIS OF HEAT TRANSFER ENHANCING PARAMETERS ON IMPINGING AIR JETS

Burak TURKAN
Akin Burak ETEMOGLU
Sayfa
1017–1030
Yayın Tarihi
2020-09-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

In this study, a numerical approach is presented to find an optimum solution for cooling problems in the electronics industry.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Impinging air jets are widely used in industry for heating, cooling and drying.
📊
Temel Bulgular & Veri:Air velocity (12, 23 and 35 m/s), geometry dimensions (H/D distance= 4, 6, 8, 10, 12), number of nozzles (single and double) and the distance between nozzles (n = 50, 75, 100) were selected as parameters.
💡
Sonuç & Katkı:In this study, a numerical approach is presented to find an optimum solution for cooling problems in the electronics industry.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Heat transfer · impinging air jet · numerical method

Abstract

Impinging air jets are widely used in industry for heating, cooling and drying. Single and multiple impinging air jets provide the best configuration for convective heat and mass transfer to a surface. In this study, the convection air jets were examined numerically. Air velocity (12, 23 and 35 m/s), geometry dimensions (H/D distance= 4, 6, 8, 10, 12), number of nozzles (single and double) and the distance between nozzles (n = 50, 75, 100) were selected as parameters. For single nozzle, the most efficient condition was seen in H/D=10 and the highest Reynolds number. It was determined that the efficiency of heat transfer after H/D=10 has decreased for single nozzle. The most efficient heat transfer for the double nozzle was obtained for the 12114 of Reynolds number and H/D=8. In this study, a numerical approach is presented to find an optimum solution for cooling problems in the electronics industry.

🔖

Bu Makaleye Atıf Yap

TURKAN, B., ETEMOGLU, A. B. (2020). NUMERICAL ANALYSIS OF HEAT TRANSFER ENHANCING PARAMETERS ON IMPINGING AIR JETS. Sigma Mühendislik ve Fen Bilimleri Dergisi, Cilt: 37 - Sayı: 3, 1017–1030. https://ajindex.com/articles/419165

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Calisir T., Caliskan S., Kılıc M., Baskaya S., (2017) Numerical Investigation of Flow Field on Ribbed Surfaces Using Impinging Jets, Journal of the Faculty of Engineering and Architecture of Gazi University, 32(1), 119-130
  2. Hatemi M., Song D., Jing D., (2016) Optimization of a Circular-Wavy Cavity Filled by Nanofluid Under the Natural Convection Heat Transfer Condition, International Journal of Heat and Mass Transfer, 98, 758-767
  3. Tang W., Hatami M., Zhou J., Jing D., (2017) Natural Convection Heat Transfer in a Nanofluid-Filled Cavity with Double Sinusoidal Wavy Walls of Various Phase Deviations, International Journal of Heat and Mass Transfer,115(A), 430-440
  4. Zhou J., Hatami M., Song D., Jing D., (2016) Design of Microchannel Heat Sink with Wavy Channel and its Time-Efficient Optimization with Combined RSM and FVM Methods, International Journal of Heat and Mass Transfer, 103, 715-724
  5. Hardisty H., Can M., (1983) An Experimental Investigation Into The Effect of Changes in the Geometry of a Slot Nozzle on the Heat Transfer Characteristics of an Impinging Air Jet, Proc. Inst. Mech. Engs., 197C, 7-15
  6. Gau C., Chung C.M., (1991) Surface Curvature Effect on Slot- Air-Jet Impingement Cooling Flow and Heat Transfer Process, Institute of Aeronautics and Astronautics, National Cheng Kung University, Tainan, Taiwan
  7. Golcu M., Yazici H., Akcay M., Koseoglu M.F., Sekmen Y., (2012) Experimental Investigation of Cooling With Multiple Air Jets on Auto Glass Tempering, Journal of the Faculty of Engineering and Architecture of Gazi University, 27, 775-783
  8. Fregeau M., Saeed F., Paraschiviou I., (2005) Numerical Heat Transfer Correlation For Array of Hot-Air Jets Impinging on 3-Dimensional Concave Surface, Journal of Aircraft, 42(3), 665-670
  9. Celik N., Eren H., (2009) Effects of Stagnation Region Turbulence of an Impinging Jet on Heat Transfer, Journal of Thermal Science and Technology, 30(1), 91-98
  10. Garimella V. P., (2001) Local Heat Transfer Distributions in Confined Multiple Air Jet Impingement, ASME Journal of Electronic Packaging, 123(3), 165-172
  11. Elibol E. A., Turkoglu H., (2017) Numerical Investigation of Impinging Jets on a Flat Plate Covered with Porous Layer, The Black Sea Journal of Sciences, 7(1), 9-28
  12. Geers L.F.G., Tummers M. J., Bueninck T. J., Hanjalic K., (2008) Heat Transfer Correlation for Hexagonal and In-Line Arrays of Impinging Jets, International Journal of Heat and Mass Transfer, 51(21-22), 5389–5