Dergiler / Electrica / 2021 / Cilt: 21 - Sayı: 2

Warpage Reduction for Power MOSFET Wafers

Sayfa
173–179
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Hence, the sputtering power could be adjusted to ensure that the warpage effectstays below its critical value

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Wafer warpage is a baseline issue faced by semiconductor manufacturers and is, in fact, particularly conspicuous among those which are involved in thefabrication of power metal oxide semiconductor field effect transistors (MOSFETs).
📊
Temel Bulgular & Veri:This is because vertical MOSFETs experience larger warpage effectscompared with their conventional lateral counterparts.
💡
Sonuç & Katkı:Hence, the sputtering power could be adjusted to ensure that the warpage effectstays below its critical value
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

Wafer warpage is a baseline issue faced by semiconductor manufacturers and is, in fact, particularly conspicuous among those which are involved in thefabrication of power metal oxide semiconductor field effect transistors (MOSFETs). This is because vertical MOSFETs experience larger warpage effectscompared with their conventional lateral counterparts. Wafers with warpage exceeding its critical value fail to be chucked by vacuum adsorption duringthe automatic handling process; the devices fabricated in the wafer face reliability issues as well. This paper presents an analysis on various mechanismsemployed to reduce warpage in power MOSFET wafers. The warpage behavior was examined by varying the backside metallization (BSM) thickness, thesputtering power for film deposition and the wafer’s temperature (i.e., a cryogenic condition was introduced into the process). The results suggest thatboth the BSM thickness and wafer’s temperature do not manifest a clear correlation with the wafer warpage when the front-end fabrication process iscompleted. The wafer bow level was, however, found to be in direct proportion with the magnitude of the sputtering power. When the sputtering poweris reduced, less residual stress is induced to deform the wafer structure. Hence, the sputtering power could be adjusted to ensure that the warpage effectstays below its critical value

🔖

Bu Makaleye Atıf Yap

YEAP, K. H., NİSAR, H., DAKULAGİ, V. (2021). Warpage Reduction for Power MOSFET Wafers. Electrica, Cilt: 21 - Sayı: 2, 173–179. https://ajindex.com/articles/348139

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (1)

  1. I. Ahmad, Y. K. Ho, B. Y. Majlis, “Fabrication and Characterization of a 0.14 μm CMOS Device Using ATHENA and ATLAS Simulators”, International Scientific Journal of Semiconductor Physics, Quantum Electronics, and Optoelectronics, vol. 9, no. 2, pp. 40-44, Mar. 2006. [Crossref] 2. K. H. Yeap, J. Y. Lee, W. L. Yeo, H. Nisar, S. H. Loh, “Design and Characterization of a 10 nm FinFET”, Malaysian Journal of Fundamental and Applied Sciences, vol. 15, no. 4, pp. 609-612, Aug. 2019. [Crossref] 3. Y. K. Ho, M. K. Meng, L. K. Chun, T. P. Chiong, H. Nisar, Z. I. Rizman, “Design and Analysis of 15 nm MOSFETs”, Journal of Telecommunication, Electronic and Computer Engineering, vol. 8(12), 2016, pp. 1 - 4. 4. K. H. Yeap, K. W. Thee, K. C. Lai, H. Nisar, K. C. Krishnan, “VLSI Circuit Optimization for 8051 MCU”, International Journal of Technology, vol. 9, no. 1, pp. 142-149, 2018. [Crossref] 5. R. K. Williams, M. N. Darwish, R. A. Blanchard, R. Siemieniec, P. Rutter, Y. Kawaguchi, “The trench power MOSFET: Part I-History, technology, and prospects”. IEEE Transactions on Electron Devices, vol. 64, no. 3, pp. 674-691, 2017. [Crossref] 6. Y. P. Tsividis, “Chapter 5-Short channel & narrow channel effects,” in Operation and Modeling of the MOS Transistor. New York, NY, USA: McGraw-Hill, pp. 181-191, 1987. 7. M. J. Declercq, J. D. Plummer, “Avalanche breakdown in high-voltage DMOS devices,” IEEE Trans Device, vol. 23, no. 1, pp. 1-4, Jan. 1976. [Crossref] 8. W. Zhang, W. Liu, B. Ma, “Optimization of backside metal deposition in power IC process for suppression of wafer warpage and film peeling issue”. In 2018 China Semiconductor Technology International Conference (CSTIC), pp. 1-11, Mar. 2018. [Crossref] 9. H. Kato, T. Nishiguchi, S. Shimomura, K. Miyashita, K. Kobayashi, “Mechanism and Control Technique of Wafer Warpage in Process Integration for Trench Field Plate Power MOSFET”, IEEE Transactions on Semiconductor Manufacturing, vol. 32, no. 4, pp. 417- 422, 2019. [Crossref] 10. H. Kato, K. Kobayashi, T. Nishiguchi, S. Shimomura, “Process Control Technique to Reduce Wafer Warpage for Trench Field Plate Power MOSFET”, In 2018 International Symposium on Semiconductor Manufacturing (ISSM), pp. 1-4, Dec. 2018. [Crossref] 11. Y. Baba, N. Matsuda, S. Yanagiya, S. Hiraki, S. Yasuda, “A Study on a High Blocking Voltage UMOS-FET with a Double Gate Structure,” Proc. of ISPSD, pp. 300-302, 1992. 12. W. Saito, “Comparison of Theoretical Limits between Superjunction and Field Plate Str