Dergiler / Ondokuz Mayıs Üniv. Diş Hekimliği Derg. / 2009 / Cilt: 10 - Sayı: 2

Farklı bağlantı materyallerinin metal-seramik bağlantısına etkisinin karşılaştırmalı olarak incelenmesi

Comparative investigation of the effect of different bonding materials on metal-ceramic bond

Sayfa
9–15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Bulgular: Bağlantı kuvveti yönünden gruplar arasında i s t a t i s t i k s e l a ç ı d a n a n l aml ı f a r k l ı l ı k l a r bulunmuştur(P<0.0001).

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Amaç: Metal-seramik bağlantısı, restorasyonun başarısını etkileyen başlıca faktörlerden biridir ve bu bağlantının güçlü olmasında oksit tabakanın payı büyüktür.
📊
Temel Bulgular & Veri:Bu çalışmanın amacı, bağlantı materyallerinin metal seramik bağlantısı üzerine etkisini karşılaştırmalı olarak incelemektir.
💡
Sonuç & Katkı:Bulgular: Bağlantı kuvveti yönünden gruplar arasında i s t a t i s t i k s e l a ç ı d a n a n l aml ı f a r k l ı l ı k l a r bulunmuştur(P<0.0001).
🔬Tür:Araştırma Makalesi
📍Kapsam:40 örnek
⚙️Değişkenler:Dental bağlanma · Karşılaştırmalı çalışma · Dental restorasyon

Özet

Amaç: Metal-seramik bağlantısı, restorasyonun başarısını etkileyen başlıca faktörlerden biridir ve bu bağlantının güçlü olmasında oksit tabakanın payı büyüktür. Opak porseleni metal yüzeyinde oluşan oksit tabaka ile ısısal işlem sonucunda birleşir. Bu çalışmanın amacı, bağlantı materyallerinin metal seramik bağlantısı üzerine etkisini karşılaştırmalı olarak incelemektir. Gereç ve Yöntem: Çalışmada beş farklı bağlantı materyali (Ceramco; Grup C, Ivoclar; Grup I, Keramik; Grup K, Realite; Grup R, Vita; Grup V (kontrol)), metal alaşımı (Remanium) ve dentin porseleni (Vita VMK 95) kullanılmıştır. Silindirik örneklerin porselen kısmının boyutları 4x4mm, metal kısmının boyutları ise tabanı 5x1mm ve porselenle birleşecek kısmı 4x4mm şeklindedir. Hazırlanan 40 örnek, 1mm/dak hızla makaslama kuvvetine maruz kalmıştır. Bağlantı kuvvetlerinin değerleri ANOVA ve ardından Tukey çoklu karşılaştırma testleri kullanılarak test edilmiştir (α=.05). Kırık yüzeyler stereomikroskop ile incelenmiştir. Bulgular: Bağlantı kuvveti yönünden gruplar arasında i s t a t i s t i k s e l a ç ı d a n a n l aml ı f a r k l ı l ı k l a r bulunmuştur(P<0.0001). Grup C'nin değerleri (925.12±46.08N) diğer gruplardan daha yüksek olduğu görülmüştür. Grup I(528.12 ± 41.02 N) ve Grup V(528.25±37.29N) arasında da anlamlı bir fark görülmezken, her iki grubun, grup C, grup R(605.88±39.77N) ve grup K(643.12± 63.15N)'dan anlamlı şekilde düşük olduğu izlenmiştir. Kırık yüzey görüntüleri gruplar arasında benzerlik göstermiştir. Sonuç: Metal seramik reatorasyonların yapımında bağlantı materyalinin önemi unutulmamalıdır ve kullanılan metal seramik sistemlerine uygun bağlantı materyalinin seçimi gerekmektedir.

Abstract

Aim: Metal-ceramic bonding is one of the factors that affect the success of the metal-ceramic restorations and oxide layer has a significant role in obtaining a strong bond. Opaque porcelain bonds to oxide layer after a thermal treatment. The aim of this study is determine the effect of opaque porcelain on the metal-ceramic bond. Material and Method: 5 different opaque porcelains (Ceramco; Group C, Ivoclar; Group I, Keramik; Group K, Realite; Group R, Vita; Group V (control)), one metal alloy (Remanium) and a dentin porcelain (Vita VMK 95) were used in this study. The porcelain portion of the cylindrical metal-ceramic specimens was 4 mm in diameter and 4 mm high; the metal portion was machined to 4 x 4 mm, with a base that had a 5 mm diameter and was 1 mm high. Shear test was applied to forty samples (n:8). Bond load was recorded. Data were analyzed with Anova and Tukey multiple choice test (&#945;=.05). Fracture surfaces were examined with a stereomicroscope. Results: Significant differences were found among mean bond loads for all groups (P<0.0001). Group C (925.12±46.08N) had the highest values among the groups. Since there was not a significant difference between Group I(528.12±41.02N) and Group V(528.25±37.29N), mean values of both groups were lower than Group C, Group R(605.88±39.77N) and Group K(643.12± 63.15N). There was a similarity among the fracture surfaces for all groups. Conclusion: The importance of opaque porcelain material during the fabrication of metal-ceramic restorations should be remembered. A proper match required between opaque porcelain and metal-ceramic systems for the success of metal-ceramic restorations.

🔖

Bu Makaleye Atıf Yap

KIURTOĞLU, C., UÇAR, Y. (2009). Farklı bağlantı materyallerinin metal-seramik bağlantısına etkisinin karşılaştırmalı olarak incelenmesi. Ondokuz Mayıs Üniv. Diş Hekimliği Derg., Cilt: 10 - Sayı: 2, 9–15. https://ajindex.com/articles/293166

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (17)

  1. Pisani-Proenca J, Erhardt MC, Valandro LF, et al. Influence of ceramic surface conditioning and resin cements on microtensile bond strength to a glass ceramic. J Prosthet Dent. 2006;96:412-17
  2. Wataha JC. Alloys for prosthodontic restorations. J Prosthet Dent. 2002;87:351-63
  3. McLean JW. Evaluation of dental ceramics in the twentieth century. J Prosthet Dent. 2001;85:61-66
  4. Anusavice K. Philips’ Science of Dental Materials, 11th edition, St Louis, Saunders, 2003, p:666-710
  5. Scolaro JM, Pereira JR, Valle AL, Bonfante G, Pegoraro LF. Comparative study of ceramic-to- metal bonding. Braz Dent J. 2007;18:240-43
  6. Joias RM, Tango RN, Junho de Araujo JE, et al. Shear bond strength of a ceramic to Co-Cr alloys. J Prosthet Dent. 2008 Jan;99:54-59
  7. Seghi RR, Denry IL, Rosenstiel SF. Relative fracture toughness and hardness of new dental ceramics. J Prosthet Dent. 1995;74:145-50
  8. Josephson BA, Schulman A, Dunn ZA, Hurwitz W. A compressive strength study of complete ceramic crowns-Part II. J Prosthet Dent. 1991;65:388-91
  9. Hammad IA, Talic FY. Designs of bond strength test for metal-ceramic complexes: review of the literature. J Prosthet Dent. 1996;75:602-608
  10. Kansu G. Temel metal alaşımları ile düşük ı sı porseleninin bağlantı dayanıklılığı. AÜ Diş Hek Fak Derg. 2001;28:185-91
  11. Papazoglou E, Brantley WA, Johnston WM, Carr AB. Effects of dental laboratory processing variables and in vitro testing medium on the porcelain adherence of high-palladium casting alloys. J Prosthet Dent.1998;79:514-19
  12. Öztaş D, Terzioğlu H. Baz metal alaşımların tekrarlanan dökümlerinin porselenin bağlanma direncine etkisi. Gülhane Tıp Derg. 2000;42:252-55 13. Yamamoto M. Metal Ceramics: Principles and Methods of Makoto Yamamoto, Chicago, Quintessence Publishing Co. Inc, 1985 p:106-203
  13. Anusavice KJ, Ringle RD, Fairhurst CW. Adherence controlling elements in ceramicmetal systems. II. Nonprecious alloys. J Dent Res. 1977;56:1053-61
  14. Ozcan M. Fracture reasons in ceramicfused- to- metal restorations. J Oral Rehabil. 2003;30:265-69
  15. Claus H. The structure and microstructure of dental porcelain in relationship to the firing conditions. Int J Prosthodont. 1989;2:373-84. 17. de Melo RM, Travassos AC, Neisser MP Shear bond strengths of a ceramic system to alternative metal alloys. J Prosthet Dent. 2005;93:64-19
  16. International Organization for Standadization. Metal ceramic dental restorative systems. 2nd edition, ISO 9693;1999(E)
  17. Papazoglou E, Br