Dergiler / Acta Odontologica Turcica / 2014 / Cilt: 31 - Sayı: 1

Isısal ve mekanik yaşlandırma işlemlerinin Y-TZP kor materyallerinin kırılma tokluğuna etkisi

Effect of thermal and mechanical aging on fracture toughness of Y-TZP core materials

Sayfa
1–6
Yayın Tarihi
2014-02-25
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

İstatistiksel analiz iki yönlü varyans analizi (ANOVA) ile yapıldı.BULGULAR: Cercon Base grubu örneklerin kırılma tokluğu değerleri, kontrol, ısısal ve mekanik yaşlandırma grubu için sırasıyla 6.28, 6.39 ve 6.02 MPa√m olarak belirlendi.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:AMAÇ: Bu çalışmanın amacı, ısısal ve mekanik yaşlandırma işlemlerinin, yttria-stabilize dörtgen zirkon (Y-TZP) kor materyallerinin kırılma tokluğu üzerindeki etkisinin araştırılmasıdır.GEREÇ VE YÖNTEM: Her iki kor materyalinden disk şeklinde üretilen Cercon Base and Lava Plus örnekler (15 mm çap 1.2 mm kalınlık) rastgele olarak 3 gruba (kontrol, ısısal yaşlandırma ve mekanik yaşlandırma) ayrıldı.
📊
Temel Bulgular & Veri:Isısal yaşlandırma işlemi 5-55 °C sıcaklıklarda su içeren banyolarda, her birinde 30 sn kalacak şekilde 104 kez uygulandı.
💡
Sonuç & Katkı:İstatistiksel analiz iki yönlü varyans analizi (ANOVA) ile yapıldı.BULGULAR: Cercon Base grubu örneklerin kırılma tokluğu değerleri, kontrol, ısısal ve mekanik yaşlandırma grubu için sırasıyla 6.28, 6.39 ve 6.02 MPa√m olarak belirlendi.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Seramikler · Yaşlanma · Yorulma Kırıkları

Özet

AMAÇ: Bu çalışmanın amacı, ısısal ve mekanik yaşlandırma işlemlerinin, yttria-stabilize dörtgen zirkon (Y-TZP) kor materyallerinin kırılma tokluğu üzerindeki etkisinin araştırılmasıdır.GEREÇ VE YÖNTEM: Her iki kor materyalinden disk şeklinde üretilen Cercon Base and Lava Plus örnekler (15 mm çap 1.2 mm kalınlık) rastgele olarak 3 gruba (kontrol, ısısal yaşlandırma ve mekanik yaşlandırma) ayrıldı. Kontrol gruplarına herhangi bir işlem yapılmadı. Isısal yaşlandırma işlemi 5-55 °C sıcaklıklarda su içeren banyolarda, her birinde 30 sn kalacak şekilde 104 kez uygulandı. Mekanik yaşlandırma işlemi ise, 200 N yük ile, 2 Hz frekansta 105 kez uygulandı. Kırılma tokluğu deneyi indentasyon kırılma metodu kullanılarak gerçekleştirildi. Her grup için on ölçüm yapıldı. Her bir indentasyon sonrası mikroskopik okuma kaydedildi ve kırılma tokluğu değeri önceden belirlenmiş bir formüle göre hesaplandı. İstatistiksel analiz iki yönlü varyans analizi (ANOVA) ile yapıldı.BULGULAR: Cercon Base grubu örneklerin kırılma tokluğu değerleri, kontrol, ısısal ve mekanik yaşlandırma grubu için sırasıyla 6.28, 6.39 ve 6.02 MPa√m olarak belirlendi. Cercon Base grubu örneklerinde, kontrol grubu ve yaşlandırma grupları arasında istatistiksel olarak anlamlı bir fark bulunmadı (p>0.05). Fakat, Cercon Base grubunda, ısısal ve mekanik yaşlandırma grupları arasında istatistiksel olarak anlamlı fark bulundu (p<0.05). Lava Plus grubu örneklerinin kırılma tokluğu değerleri, kontrol, ısısal ve mekanik yaşlandırma grubu için sırasıyla 4.79, 4.76 ve 4.91 MPa√m olarak belirlendi. Lava Plus grubu örneklerinde, kontrol grubu ve yaşlandırma grupları arasında istatistiksel olarak anlamlı bir fark bulunmadı (p>0.05).SONUÇ: Yaşlandırma işlemlerinin, kontrole kıyasla, Y-TZP kor materyallerine ait kırılma tokluğu değerlerini belirgin olarak etkilemediği tespit edildi.

Abstract

OBJECTIVE: The purpose of this study was to evaluate the effect of thermal and mechanical aging on the fracture toughness of yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) core materials.MATERIALS AND METHOD: Disc-shaped specimens for each core material (diameter: 15 mm, thickness: 1.2 mm), Cercon Base and Lava Plus, were randomly divided into three groups (control, thermal aging and mechanical aging). No aging was applied to control specimens. Thermal aging group specimens were subjected to 104 thermal cycles in water between 5-55 °C (dwell time of 30 s). Mechanical aging group specimens were subjected to a 200 N load for 105 times, with a frequency of 2 Hz. The fracture toughness of the control, thermal and the mechanical aging groups were measured by using the indentation fracture technique. Ten indentations were performed for each material. After each indentation, microscopic readings were recorded and the fracture toughness was calculated according to an established formula. Results were statistically analyzed by using a two-way analysis of variance (ANOVA) test.RESULTS: Indentation fracture toughness values of the control, the thermal and the mechanical aging groups of Cercon Base were 6.28, 6.39 and 6.02 MPa√m, respectively. There was no significant difference between the control group of Cercon Base and the aging groups (p>0.05). However, significant difference was found between the thermal and the mechanical aging groups of Cercon Base (p<0.05). Indentation fracture toughness values of the control, the thermal and the mechanical aging groups of Lava Plus were 4.79, 4.76 and 4.91 MPa√m, respectively. Again, there was no significant difference between the control the aging groups of Lava Plus (p>0.05).CONCLUSION: Compared to control, thermal and mechanical aging had no significant effect on the fracture toughness of the different Y-TZP core materials.

🔖

Bu Makaleye Atıf Yap

GÜNGÖR, M. B., YILMAZ, H., BAL, B. T., NEMLİ, S. K., SİNDEL, P. T., AYDIN, C. (2014). Isısal ve mekanik yaşlandırma işlemlerinin Y-TZP kor materyallerinin kırılma tokluğuna etkisi. Acta Odontologica Turcica, Cilt: 31 - Sayı: 1, 1–6. https://ajindex.com/articles/265336

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (16)

  1. Yılmaz H, Nemli SK, Aydin C, Bal BT, Tıraş T. Effect of fatigue on biaxial flexural strength of bilayered porcelain/zirconia (Y-TZP) dental ceramics. Dent Mater 2011;27:786-95
  2. Cattani-Lorente M, Scherrer SS, Ammann P, Jobin M, Wiskott HW. Low temperature degradation of a Y-TZP dental ceramic. Acta Biomater 2011;7:858-65
  3. Conrad HJ, Seong WJ, Pesun IJ. Current ceramic materials and systems with clinical recommendations: a systematic review. J Prosthet Dent 2007;98:389-404
  4. Harada K, Shinya A, Yokoyama D, Shinya A. Effect of loading conditions on the fracture toughness of zirconia. J Prosthodont Res 2013;57:82-7
  5. Yilmaz H, Aydin C, Gul BE. Flexural strength and fracture toughness of dental core ceramics. J Prosthet Dent 2007;98:120-8
  6. Fischer H, Marx R. Fracture toughness of dental ceramics: comparison of bending and indentation method. Dent Mater 2002;18:12-9
  7. Guazzato M, Albakry M, Ringer SP, Swain MV. Strength, fracture toughness and microstructure of a selection of all-ceramic materials. Part I. Pressable and alumina glass-infiltrated ceramics. Dent Mater 2004;20:441-8
  8. Quinn GD, Salem J, Bar-on I, Cho K, Foley M, Fang H. Fracture of advanced ceramics at room temperature. J Res Natl Inst Stand Technol 1992;97:579-607
  9. Fujii T, Nose T. Evaluation of fracture toughness for ceramic materials. IJIS Int 1989;29:717-25
  10. Nose T, Fujii T. Evaluation of fracture toughness for ceramic materials by a single-edge-precracked-beam method. J Am Ceram Soc 1988;71:328-33
  11. Srawley JE. Wide range stress ıntensity factor expressions for ASTM E 399 standard fracture toughness specimens. Int J Fract 1976;12:475- 6
  12. Chantikul PG, Anstis R, Lawn BR, Marshall DB. A Critical Evaluation of Indentation Techniques for Measuring Fracture Toughness: II, Strength Method. J Am Ceram Soc 1981;64:539-43
  13. Anstis GR, Chantikul P, Lawn BR, Marshall DB. A critical evaluation of indentation techniques for measuring fracture toughness: I, Direct crack measurements. J Am Ceram Soc 1981;64:533-8
  14. Nemli SK, Yilmaz H, Aydin C, Bal BT, Tıraş T. Effect of fatigue on fracture toughness and phase transformation of Y-TZP ceramics by Xray diffraction and Raman spectroscopy. J Biomed Mater Res B Appl Biomater 2012:100B:416-24
  15. Borchers L, Stiesch M, Bach FW, Buhl JC, Hübsch C, Kellner T, et al. Influence of hydrothermal and mechanical conditions on the strength of zirconia. Acta Biomater 2010;6:4547-52
  16. Studart AR, Filser F, Kocher P, Gauckler LJ. Fa