Dergiler / Bor Dergisi / 2019 / Cilt: 4 - Sayı: 1

Surface modification of anhydrous borax powders with stearic acid via mechanical dry powder coating

Sayfa
7–15
Yayın Tarihi
2019-03-16
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

As a conclusion, an effective mechanical dry coating processing by a one-step coating approach could be applied to obtain a modified anhydrous borax surface, which offers controlled solubility behaviour in water-based suspensions.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Surface modification of anhydrous borax powders with stearic acid in the laboratory-scale planetary ball mill via mechanical dry powder coating approach was investigated.
📊
Temel Bulgular & Veri:The cohesion mechanisms of powders, which processed at conditions of 0.5, 1 and 2 wt. % stearic acid amount with the function of 30, 60 and 120 minute activation time, were evaluated in terms of the solubility test, contact angle measurements, particle size distributions, and scanning electron microscopy (SEM) analysis.
💡
Sonuç & Katkı:As a conclusion, an effective mechanical dry coating processing by a one-step coating approach could be applied to obtain a modified anhydrous borax surface, which offers controlled solubility behaviour in water-based suspensions.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Anhydrous borax · Stearic acid · Surface modification

Abstract

Surface modification of anhydrous borax powders with stearic acid in the laboratory-scale planetary ball mill via mechanical dry powder coating approach was investigated. The alteration of hydrophilic surface properties of anhydrous borax with stearic acid was optimized by modifier amount and activation time. The cohesion mechanisms of powders, which processed at conditions of 0.5, 1 and 2 wt. % stearic acid amount with the function of 30, 60 and 120 minute activation time, were evaluated in terms of the solubility test, contact angle measurements, particle size distributions, and scanning electron microscopy (SEM) analysis. Results indicate that anhydrous borax surface could be switched from hydrophilic to hydrophobic with changing contact angle from wetting (17o) to non-wetting (99o). Water-insoluble amount of anhydrous borax powders, as a coating efficiency indicator, was increased from 73 % to 91 % by coating with 1 wt. % stearic acid for 60 min. Furthermore, SEM analysis results demonstrate that stearic acid was discretely coated over the anhydrous borax surface. As a conclusion, an effective mechanical dry coating processing by a one-step coating approach could be applied to obtain a modified anhydrous borax surface, which offers controlled solubility behaviour in water-based suspensions.

🔖

Bu Makaleye Atıf Yap

AKPINAR, S., ARSOY, Z., ŞENOL, R. S. (2019). Surface modification of anhydrous borax powders with stearic acid via mechanical dry powder coating. Bor Dergisi, Cilt: 4 - Sayı: 1, 7–15. https://ajindex.com/articles/252171

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (16)

  1. McMillian P. W., Glass-Ceramics, 2nd Edition, Academic Press, New York, 1979
  2. Kingery W. D., Bowen H. K., Uhlmann, D. R., Introduction to Ceramics, John Wiley and Sons, New York, 1976
  3. Hawthorne F. C., Burns P. C., Grice J. D., The crystal chemistry of boron. In Boron Mineralogy, Petrology and Geology (E. S. Grew and L. M. Anevitz, Eds.), Mineral Society American, MSA Reviews in Mineralogy, 33 (2), 41-116, 1996
  4. Helvaci C. Borates, in Encyclopedia of Geology, (Selley R.C., Cocks, L.R.M and Plimer, I.R., eds.), Elsevier, (3), 510-522, 2005
  5. Kirk-Othmer, Encyclopedia of Chemical Technology, Ch.4, 5th Edition, 241-294, 2004
  6. Akpinar S., Yazici Z.O., Can M.F., Investigation of surface-modified anhydrous borax utilisation in raw glazes, Ceram. Int 44, 18344–18351, 2018
  7. ECETOC Technical Report No. 63, Reproductive and General Toxicology of Some Inorganic Borates and Risks Assessment for Human Beings, European Centre for Ecotoxicology and Toxicology of Chemicals (ECETOC), Brussels, Belgium, 3, 1995
  8. Kaplan J., Zamek J., A substitute for gerstley borate, Ceramics Technical, 32, 24-29, 2011
  9. Otles M. S., Modification of surface properties of biopowders by dry particle coating, Ph.D. Thesis, Université de Toulouse, National Institute of Posts and Telecommunications, Rabat, 2008
  10. Pfeffer R., Dave R. N., Dongguang W., Ramlakhan M., Synthesis of engineered particulates with tailored properties using dry particle coating, Powder Technol., 117, pp.40-67, 2001
  11. Yoshihara I., Pieper W., Hybridization–technology for surface modification of powders without binders, Swiss Pharma 6, 21, 1999
  12. Ouabbas Y., Chamayou A., Galet L., Baron M., Thomas G., Grosseau P., Guilhot B., Surface modification of silica particles by dry coating: Characterization and powder ageing, Powder Technol., 190a, 200-209, 2009
  13. Lefebvre G., Galet L., Chamayou A., Dry coating of talc particles: Effect of material and process modifications on their wettability and dispersibility, AIChE Journal, 57 (1), 79-86, 2011
  14. Sonoda R., Horibe M., Oshima T., Iwasaki T., Watano S., Improvement of dissolution property of poorly water-soluble drug by novel dry coating method using planetary ball mill, Chem. Pharm. Bull. 56 (9),1243-7, 2008
  15. Tsai W. T., Microstructural characterization of calcite-based powder materials prepared by planetary ball milling, Materials, 6, 3361-3372, 2013
  16. Suryanarayana C., Mechanical alloying and milling, Prog. Mater Sci