Dergiler / Electrica / 2021 / Cilt: 21 - Sayı: 1

Three Speed Controllers of Direct Torque Control for a Doubly Fed Induction Motor Drive–A Comparison

Sayfa
129–141
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

A comparative analysis of these speed controllers of the DTC strategy is conducted and discussed, highlighting the method that best meets the requirements in terms of dynamic response, references tracking, torque ripple, complexity, and robustness to torque variation.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This research paper presents the performance of direct torque control (DTC) for a doubly fed induction motor (DFIM).
📊
Temel Bulgular & Veri:The DFIM performance depends mainly on the design of the speed controller.
💡
Sonuç & Katkı:A comparative analysis of these speed controllers of the DTC strategy is conducted and discussed, highlighting the method that best meets the requirements in terms of dynamic response, references tracking, torque ripple, complexity, and robustness to torque variation.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

This research paper presents the performance of direct torque control (DTC) for a doubly fed induction motor (DFIM). The DFIM performance depends mainly on the design of the speed controller. The traditional proportional-integral (PI) speed controller is not very effective when the system is highly perturbed, and its gain values depend on engine parameters that are not constant. Consequently, a robust speed controller is required to achieve a high-performance drive. A backstepping speed controller is developed to achieve continuous control of the motor speed and torque. In addition, the fuzzy logic speed controller is designed to achieve high performance, speed accuracy, dynamic tracking behavior, and robustness to load disturbances. The control algorithms offered are simulated and tested in a MATLAB/Simulink environment. A comparative analysis of these speed controllers of the DTC strategy is conducted and discussed, highlighting the method that best meets the requirements in terms of dynamic response, references tracking, torque ripple, complexity, and robustness to torque variation.

🔖

Bu Makaleye Atıf Yap

MAHFOUD, M. E., BOSSOUFİ, B., OUANJİLİ, N. E., MAHFOUD, S., TAOUSSİ, M. (2021). Three Speed Controllers of Direct Torque Control for a Doubly Fed Induction Motor Drive–A Comparison. Electrica, Cilt: 21 - Sayı: 1, 129–141. https://ajindex.com/articles/198846

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (1)

  1. A. Bakouri, H. Mahmoudi, A. Abbou, "Intelligent control for doubly fed induction generator connected to the electrical network", Int. J. Power Electron. Drive Syst., vol. 7, no. 3, pp. 688-700, 2016. [Crossref] 2. B. Bossoufi, M. Karim, A. Lagrioui, M. Taoussi, A. Derouich, "Observer backstepping control of DFIG-Generators for wind turbines variable-speed: FPGA-based implementation", Renew. Energy, vol. 81, pp. 903-917, 2015. [Crossref] 3. F. Bonnet, P.E. Vidal, M. Pietrzak-David, "Direct torque control of doubly fed induction machine", Bulletin of the polish academy of sciences technical sciences, vol. 54, no. 3, pp. 307-314, 2006. 4. R. Babouri, D. Aouzellag, K. Ghedamsi, "Introduction of doubly fed induction machine in an electric vehicle", Energy Procedia, vol. 36, pp. 1076-1084, 2013. [Crossref] 5. M. Taoussi, M. Karim, B. Bossoufi, D. Hammoumi, A. Lagrioui, A. Derouich, "Speed variable adaptive backstepping control of the doubly-fed induction machine drive", Int. J. Autom. Control, vol. 10, no. 1, pp. 12-33, 2016. [Crossref] 6. M. Elmahfoud, B. Bossoufi, M. Taoussi, N. El Ouanjli, A. Derouich, "Rotor Field Oriented Control of Doubly Fed Induction Motor", 2019 Int. Conf. Optim. Appl. ICOA 2019, 2019. [Crossref] 7. N. El Ouanjli, A. Derouich, A. El Ghzizal, A. Chebabhi, M. Taoussi, "A comparative study between FOC and DTC control of the Doubly Fed Induction Motor (DFIM)", Proc. 2017 Int. Conf. Electr. Inf. Technol. ICEIT 2017, vol. 2018-Janua, pp. 1-6, 2018. [Crossref] 8. I. Takahashi, T. Noguchi, "A New Quick-Response and High-Efficiency Control Strategy of an Induction Motor", IEEE Trans. Ind. Appl., vol. IA-22, no. 5, pp. 820-827, 1986. [Crossref] 9. T. Sutikno, N. R. N. Idris, A. Jidin, "A review of direct torque control of induction motors for sustainable reliability and energy efficient drives", Renew. Sustain. Energy Rev., vol. 32, pp. 548-558, 2014. [Crossref] 10. S. K. Barik, K. K. Jaladi, "Five-Phase Induction Motor DTC-SVM Scheme with PI Controller and ANN Controller", Procedia Technol., vol. 25, no. Raerest, pp. 816-823, 2016. [Crossref] 11. N. E. Ouanjli, A. Derouich, A. E. Ghzizal, S. Motahhir, A. Chebabhi, Y. E. Mourabit, M. Taoussi, "Direct torque control of doubly fed induction motor using three-level NPC inverter," Prot. Control Mod. Power Syst., vol. 4, no. 1, 2019. [Crossref] 12. N. E. Ouanjli, A. Derouich, A. E. Ghzizal, S. Motahhir, A. Chebabhi, Y. E. Mourabit, M. Taoussi, "Modern improvement techniques of direct torque control