KaydedilenlerDerginizi ekleyin

Dergiler / Firat University Journal of Experimental and Computational Engineering / 2026 / Cilt: 5 Sayı: 3

Çok Malzemeli FDM ile Üretilen Fonksiyonel Derecelendirilmiş Karbon Fiber Takviyeli PLA Kompozitlerinin Mekanik Performansı

Mechanical Performance of Functionally Graded Carbon Fiber-Reinforced PLA Composites Fabricated via Multi-Material FDM

Muhammet Mevlüt Karaca(KARABÜK ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ)0000-0001-9644-3663
Tuğçe Yildiz(KARABÜK ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ)0000-0002-5361-7923
Sayfa
671–685
Yayın Tarihi
2026-10-25
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Elde edilen sonuçlar, çok malzemeli FDM yöntemi ile üretilen fonksiyonel derecelendirilmiş (FGM) karbon fiber takviyeli PLA kompozitlerinde katman dizilimi ile fiber oranı etkileşiminin mekanik performansın belirlenmesinde kritik bir rol oynadığını ortaya koymaktadır.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada, çok malzemeli FDM (Fused Deposition Modeling) yöntemi kullanılarak üretilen karbon fiber (CF) takviyeli polylactic acid (PLA) kompozitlerinin mekanik performansları incelenmiştir.
📊
Temel Bulgular & Veri:Üretim sürecinde saf PLA, %5 karbon fiber takviyeli PLA (5CF) ve %10 karbon fiber takviyeli PLA (10CF) filamentleri kullanılarak tek katmanlı, iki katmanlı ve üç katmanlı yapı konfigürasyonları oluşturulmuştur.
💡
Sonuç & Katkı:Elde edilen sonuçlar, çok malzemeli FDM yöntemi ile üretilen fonksiyonel derecelendirilmiş (FGM) karbon fiber takviyeli PLA kompozitlerinde katman dizilimi ile fiber oranı etkileşiminin mekanik performansın belirlenmesinde kritik bir rol oynadığını ortaya koymaktadır.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Çok malzemeli FDM · Karbon fiber takviyeli PLA · Katmanlı yapı

Özet

Bu çalışmada, çok malzemeli FDM (Fused Deposition Modeling) yöntemi kullanılarak üretilen karbon fiber (CF) takviyeli polylactic acid (PLA) kompozitlerinin mekanik performansları incelenmiştir. Üretim sürecinde saf PLA, %5 karbon fiber takviyeli PLA (5CF) ve %10 karbon fiber takviyeli PLA (10CF) filamentleri kullanılarak tek katmanlı, iki katmanlı ve üç katmanlı yapı konfigürasyonları oluşturulmuştur. Boyutsal doğruluk analizleri, tüm numunelerde ±0.1 mm tolerans aralığında yüksek geometrik hassasiyet elde edildiğini göstermiştir. İki katmanlı yapıların mekanik performansı, tek katmanlı yapılara kıyasla daha yüksek bulunmuştur; alt katmanı saf PLA ve üst katmanı %5 CF-PLA olan iki katmanlı yapı, çekme dayanımında %19, elastik modülde %74 ve eğilme dayanımında %24 oranında iyileşme sağlamıştır (2T-5CF). Üç katmanlı (PLA/%5 CF/%10 CF) hibrit yapı, saf PLA'ya kıyasla elastik modülde %65 ve eğilme dayanımında %4,2 oranında artış sunmuştur (3T). Bununla birlikte, 3T konfigürasyonunun eğilme dayanımı (69,17 MPa), tek katmanlı 5CF (78,08 MPa) ve 10CF (70,71 MPa) numunelerinin altında kalmış; bu durum, gradyan karakterine karşın üç katmanlı yapının tek katmanlı CF takviyeli yapılara kıyasla eğilme dayanımı açısından herhangi bir avantaj sunmadığına işaret etmektedir. Katmanlar arası geçiş bölgeleri ve olası ayrılmaların değerlendirilmesi amacıyla kırılma yüzeyleri taramalı elektron mikroskobu (SEM) kullanılarak incelenmiştir. Elde edilen sonuçlar, çok malzemeli FDM yöntemi ile üretilen fonksiyonel derecelendirilmiş (FGM) karbon fiber takviyeli PLA kompozitlerinde katman dizilimi ile fiber oranı etkileşiminin mekanik performansın belirlenmesinde kritik bir rol oynadığını ortaya koymaktadır.

Abstract

In this study, the mechanical performances of carbon fiber (CF) reinforced polylactic acid (PLA) composites produced using the multi-material FDM (Fused Deposition Modeling) method were investigated. Single-, two-, and three-layer configurations were fabricated using pure PLA, 5% carbon fiber-reinforced PLA (5CF), and 10% carbon fiber-reinforced PLA (10CF) filaments. Dimensional accuracy analyses showed that high geometric precision within ±0.1 mm was achieved for all specimens. The mechanical performance of the two-layer structures was higher compared to single-layer structures. The two-layer structure with a bottom layer of pure PLA and a top layer of 5% CF-PLA showed a 19% improvement in tensile strength, a 74% improvement in elastic modulus, and a 24% improvement in flexural strength (2T-5CF). The three-layer (PLA/5% CF/10% CF) hybrid structure provided a 65% increase in elastic modulus and a 4.2% increase in flexural strength compared to pure PLA (3T). However, the flexural strength of the 3T configuration (69.17 MPa) remained below that of the single-layer 5CF (78.08 MPa) and 10CF (70.71 MPa) specimens, indicating that the three-layer arrangement offers no flexural strength advantage over single-layer CF-reinforced structures despite its gradient character. The fracture surfaces were examined using scanning electron microscopy (SEM) to evaluate interlayer transition regions and possible separations. The results reveal that the interaction of layer alignment and fiber ratio plays a decisive role in shaping the mechanical performance in functionally graded (FGM) carbon fiber reinforced PLA composites produced by the multi-material FDM method.

🔖

Bu Makaleye Atıf Yap

Karaca, M. M., Yildiz, T. (2026). Çok Malzemeli FDM ile Üretilen Fonksiyonel Derecelendirilmiş Karbon Fiber Takviyeli PLA Kompozitlerinin Mekanik Performansı. Firat University Journal of Experimental and Computational Engineering, Cilt: 5 Sayı: 3, 671–685. https://doi.org/10.62520/fujece.1924232

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (37)

  1. M. A. Caminero, J. M. Chacón, I. García-Moreno, and J. M. Reverte, “Interlaminar bonding performance of 3D printed continuous fibre reinforced thermoplastic composites using fused deposition modelling,” Polym. Test., vol. 68, pp. 415–423, Jul. 2018.
  2. A. Temiz, A. F. Yılmaz, F. H. Öztürk, F. Pehlivan, and M. M. Karaca, “Design and evaluation of hierarchical strut-based lattices with triply periodic minimal surface-inspired shells for bioinspired applications,” J. Mater. Eng. Perform., vol. 35, no. 13, pp. 12667–12681, Apr. 2026.
  3. S. Prajapati, J. K. Sharma, S. Kumar, S. Pandey, and M. K. Pandey, “A review on comparison of physical and mechanical properties of PLA, ABS, TPU, and PETG manufactured engineering components by using fused deposition modelling,” Mater. Today Proc., May 2024.
  4. B. Blake, R. Mendenhall, and B. Eslami, “Balancing strength and flexibility: Mechanical characterization of carbon fiber-reinforced PLA composites in FDM 3D printing,” J. Manuf. Mater. Process., vol. 9, no. 9, Art. no. 288, Sep. 2025.
  5. M. M. Karaca, İ. Ekinci, and D. Ali, “Effect of geometric modifications on the compressive strength and mechanical performance of gyroid-based bone scaffolds,” Int. J. 3D Print. Technol. Digit. Ind., vol. 9, no. 1, pp. 63–72, Apr. 2025.
  6. N. Maqsood and M. Rimašauskas, “Characterization of carbon fiber reinforced PLA composites manufactured by fused deposition modeling,” Compos. C Open Access, vol. 4, Art. no. 100112, Mar. 2021.
  7. A. Thirugnanasamabandam, M. Subramaniyan, B. Prabhu, and K. Ramachandran, “Development and comprehensive investigation on PLA/carbon fiber reinforced PLA based structurally alternate layered polymer composites,” J. Ind. Eng. Chem., vol. 136, pp. 248–257, Aug. 2024.
  8. Ö. Öz, F. H. Öztürk, and C. Güleç, “Effect of fiber content and plasticizer on mechanical and joint properties of carbon fiber powder reinforced PLA manufactured by 3D printing process,” J. Adhes. Sci. Technol., vol. 37, no. 15, pp. 2208–2231, Aug. 2023.
  9. M. Cao et al., “Investigation of carbon fiber on the tensile property of FDM-produced PLA specimen,” Polymers, vol. 14, no. 23, Art. no. 5230, Jan. 2022.
  10. T. Kuncius, M. Rimašauskas, and R. Rimašauskienė, “Interlayer adhesion analysis of 3D-printed continuous carbon fibre-reinforced composites,” Polymers, vol. 13, no. 10, Art. no. 1653, Jan. 2021.
  11. F. Ning, W. Cong, J. Qiu, J. Wei, and S. Wang, “Additive manufacturing of carbon fiber reinforced thermoplastic composites using fused deposition modeling,” Compos. B Eng., vol. 80, pp. 369–378, Oct. 2015.
  12. L. Bade, P. M. Hackney, I. Shyha, and M. Birkett, “Investigation into the development of an additive manufacturing technique for the production of fibre composite products,” Procedia Eng., vol. 132, pp. 86–93, Jan. 2015.
  13. X. Yao, C. Luan, D. Zhang, L. Lan, and J. Fu, “Evaluation of carbon fiber-embedded 3D printed structures for strengthening and structural-health monitoring,” Mater. Des., vol. 114, pp. 424–432, Jan. 2017.
  14. J. A. Paz-González et al., “Structural composite based on 3D printing polylactic acid/carbon fiber laminates (PLA/CFRC) as an alternative material for femoral stem prosthesis,” J. Mech. Behav. Biomed. Mater., vol. 138, Art. no. 105632, Feb. 2023.
  15. D. I. Stoia and E. Linul, “Tensile, flexural and fracture properties of MEX-printed PLA-based composites,” Theor. Appl. Fract. Mech., vol. 132, Art. no. 104478, Aug. 2024.
  16. M. F. Rabbi and V. Chalivendra, “Interfacial fracture characterization of multi-material additively manufactured polymer composites,” Compos. C Open Access, vol. 5, Art. no. 100145, Jul. 2021.
  17. S. Dağlı, “Mechanical characterization and interface evaluation of multi-material composites manufactured by hybrid fused deposition modeling (HFDM),” Polymers, vol. 17, no. 12, Art. no. 1631, Jan. 2025.
  18. J. L. Faust, P. G. Kelly, B. D. Jones, and J. D. Roy-Mayhew, “Effects of coefficient of thermal expansion and moisture absorption on the dimensional accuracy of carbon-reinforced 3D printed parts,” Polymers, vol. 13, no. 21, Art. no. 3637, Jan. 2021.
  19. D. Frunzaverde et al., “The influence of the layer height and the filament color on the dimensional accuracy and the tensile strength of FDM-printed PLA specimens,” Polymers, vol. 15, no. 10, May 2023.
  20. B. Ergene, Y. E. İnci, B. Çetintaş, and B. Daysal, “An experimental study on the wear performance of 3D printed polylactic acid and carbon fiber reinforced polylactic acid parts: Effect of infill rate and water absorption time,” Polym. Compos., vol. 46, no. 1, pp. 372–386, 2025.
  21. S. H. R. Sanei and D. Popescu, “3D-printed carbon fiber reinforced polymer composites: A systematic review,” J. Compos. Sci., vol. 4, no. 3, Art. no. 98, Sep. 2020.
  22. S. Ding, B. Zou, P. Wang, and H. Ding, “Effects of nozzle temperature and building orientation on mechanical properties and microstructure of PEEK and PEI printed by 3D-FDM,” Polym. Test., vol. 78, Art. no. 105948, Sep. 2019.
  23. H. Li and M. A. Huneault, “Effect of nucleation and plasticization on the crystallization of poly(lactic acid),” Polymer, vol. 48, no. 23, pp. 6855–6866, Nov. 2007.
  24. I. A. Pathek, J. R. F. da Silva, D. D. Lima, I. F. Limberger, A. A. Buenos, and C. J. Scheuer, “Assessment of carbon fiber incorporation effects on overall characteristics and properties of 3D-printed PLA,” J. Braz. Soc. Mech. Sci. Eng., vol. 46, no. 11, Art. no. 640, Oct. 2024.
  25. J.-H. Kim, H.-J. Kil, S. Lee, J. Park, and J.-W. Park, “Interfacial delamination at multilayer thin films in semiconductor devices,” ACS Omega, vol. 7, no. 29, pp. 25219–25228, Jul. 2022.
  26. A. El Moumen, M. Tarfaoui, and K. Lafdi, “Modelling of the temperature and residual stress fields during 3D printing of polymer composites,” Int. J. Adv. Manuf. Technol., vol. 104, no. 5, pp. 1661–1676, Oct. 2019.
  27. P. Singhal, P. Katiyar, U. Ramachandran, S. Davuluri, and R. Sujithra, “Mode-I and mode-II fracture toughness investigation on FDM-printed PLA/CF-PLA laminate composite,” J. Mech. Sci. Technol., vol. 39, no. 1, pp. 129–136, Jan. 2025.
  28. D. Yavas, Z. Zhang, Q. Liu, and D. Wu, “Fracture behavior of 3D printed carbon fiber-reinforced polymer composites,” Compos. Sci. Technol., vol. 208, Art. no. 108741, May 2021.
  29. Z. Wang, L. Wang, F. Tang, and C. Shen, “PLA-based composite panels prepared via multi-material fused filament fabrication and associated investigation of process parameters on flexural properties of the fabricated composite,” Polymers, vol. 16, no. 1, Art. no. 109, Jan. 2024.
  30. G. Wang, D. Zhang, G. Wan, B. Li, and G. Zhao, “Glass fiber reinforced PLA composite with enhanced mechanical properties, thermal behavior, and foaming ability,” Polymer, vol. 181, Art. no. 121803, Oct. 2019.
  31. N. A. Ibrahim, W. M. Z. W. Yunus, M. Othman, K. Abdan, and K. A. Hadithon, “Poly(lactic acid) (PLA)-reinforced kenaf bast fiber composites: The effect of triacetin,” J. Reinf. Plast. Compos., vol. 29, no. 7, pp. 1099–1111, Apr. 2010.
  32. M. Saleh, S. Anwar, A. M. Al-Ahmari, and A. Alfaify, “Compression performance and failure analysis of 3D-printed carbon fiber/PLA composite TPMS lattice structures,” Polymers, vol. 14, no. 21, Art. no. 4595, 2022.
  33. H. Cheng, L. Guo, Z. Qian, R. Sun, and J. Zhang, “Remanufacturing of recycled carbon fiber-reinforced composites based on fused deposition modeling processes,” Int. J. Adv. Manuf. Technol., vol. 116, no. 5, pp. 1609–1619, Sep. 2021.
  34. A. R. Torrado and D. A. Roberson, “Failure analysis and anisotropy evaluation of 3D-printed tensile test specimens of different geometries and print raster patterns,” J. Fail. Anal. Prev., vol. 16, no. 1, pp. 154–164, Feb. 2016.
  35. B. B. Fraj and Z. Ahmed, “Thermal, structural, and mechanical properties of carbon fiber reinforced PLA composites: Influence of FDM print speed and comprehensive analysis,” Polym. Compos., 2026.
  36. J. Bochnia, M. Blasiak, and T. Kozior, “A comparative study of the mechanical properties of FDM 3D prints made of PLA and carbon fiber-reinforced PLA for thin-walled applications,” Materials, vol. 14, no. 22, Art. no. 7062, Jan. 2021.
  37. K. Yogeshwaran and S. Das, “Mechanical properties of fused deposition modelling processed parts: A review,” Mater. Today Proc., Dec. 2022.