Dergiler / TOJSAT / 2026 / Volume: 4 Issue: 1

The Evaluation of Grinding Behaviors of Quartz and Feldspar

Dergi
TOJSAT
Sayfa
—
Yayın Tarihi
2016-07-23
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The results obtained experimental works in each of two methods is compared

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Quartz crystals are used in the electronic industry, frequency control oscillator and frequency filters.
📊
Temel Bulgular & Veri:In the size reduction, energy-intensive process is consumed about 3% of the energy produced in the industrialized countries in the world (Schonert, 1979; Narayanan, 1987).
💡
Sonuç & Katkı:The results obtained experimental works in each of two methods is compared
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Kinetic Model · Breakage Rate · Industrial Raw Materials

Abstract

Quartz crystals are used in the electronic industry, frequency control oscillator and frequency filters. Milk quartz and quartz glass by grinding and preparation procedures through the glass, detergent, paint, ceramic, sand, fill, and metallurgical industries, fine sizes (micronized) are used. Micronized feldspar group minerals, ceramics and glass industries within the limits of a certain quality have an important market due to the grinding of raw materials are widely used. In the size reduction, energy-intensive process is consumed about 3% of the energy produced in the industrialized countries in the world (Schonert, 1979; Narayanan, 1987). The size reduction operations are spent on approximately 55-70 % of the total energy consumed in the mineral processing plants (Cohen, 1983; Lynch et al., 1986). In this study, the behavior of quartz and feldspar broken into the same grinding conditions was presented Bond Grinding test and then analyzed using the kinetic model. The results obtained experimental works in each of two methods is compared

🔖

Bu Makaleye Atıf Yap

Umucu, Y., Deniz, V. (2016). The Evaluation of Grinding Behaviors of Quartz and Feldspar. TOJSAT, Volume: 4 Issue: 1. https://ajindex.com/articles/1660283

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Austin, L.G. (1972). A review introduction to the description of grinding as a rate process (pp. 1–7). Powder Technol. 5.
  2. Austin, L. G. (2002). A Treatment of Impact Breakage of Particles (pp. 85-90). Powder Tech. 126.
  3. Austin, L.G. & Brame, K. (1983). A comparison of the Bond method for sizing wet tumbling mills with a sizemass balance simulation method (pp. 261-274). Powder Technology, Vol.34.
  4. Austin, L.G., Klimpel, R.R. & Luckie, P.T. (1984). Process engineering of size reduction: ball milling, S.M.E.- A.I.M.E. New York, USA.
  5. Austin, L.G. & Luckie, P.T. (1972). Methods for determination of breakage distribution parameters (pp. 215– 222). Powder Technol. vol 5.
  6. Bond, F.C. & Maxson, W.L. (1943). Standard grindability tests and calculations (pp. 362-372). Trans. SMEAIME. Vol.153.
  7. Cohen, H. E. (1983). Energy Usage in Mineral Processing. Trans Inst. Min. Metal., 92, CI 60-164.
  8. Deister, J.D. (1987). How to determine the bond work index using lab. Ball Mill Grindability Tests, Engineering and Mining Journal.
  9. Deniz, V. (2004). Relationships between Bond’s grindability (Gbg) and breakage parameters of grinding kinetic on limestone (pp. 208–213). Powder Technol. 109