Dergiler / Engineering Sciences / 2026 / Cilt: 4 Sayı: 3

PRODUCTION OF CERAMIC REINFORCED ALUMINUM COMPOSITE MATERIALS BY USING POWDER METALLURGY METHOD AND DETERMINATION OF ITS PROPERTIES

TOZ METALURJİSİ YÖNTEMİYLE SERAMİK TAKVİYELİ ALÜMİNYUM KOMPOZİT MALZEMELERİN ÜRETİMİ VE ÖZELLİKLERİNİN INCELENMESI

Sayfa
314–322
Yayın Tarihi
2009-04-01
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The test results indicate that the mechanical properties of 99.9% Al is significantly improved with increase of SiC and FeBx particles.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:The metal matrix composites were fabricated by a powder metallurgy.
📊
Temel Bulgular & Veri:In produced composites, the reinforcement rates of FeBx are 5, 10, 15, 20, 30, 40 (%wt.) and the reinforcement rates of SiC are 2.5, 5, 7.5, 10, 15, 20 (%wt.).
💡
Sonuç & Katkı:The test results indicate that the mechanical properties of 99.9% Al is significantly improved with increase of SiC and FeBx particles.
🔬Tür:Makale
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Al-SiC Composite · Al-FeBx Composite · Powder Metallurgy

Özet

The metal matrix composites were fabricated by a powder metallurgy. In produced composites, the reinforcement rates of FeBx are 5, 10, 15, 20, 30, 40 (%wt.) and the reinforcement rates of SiC are 2.5, 5, 7.5, 10, 15, 20 (%wt.). The matrix Al powders were mechanically mixed with SiC and FeBx particulates compacted in room temperature at 400 MPa for 10x10x55mm specimens and followed by sintering at 600◦C for 1 h. Density, hardness and three point bend tests were realized. The test results indicate that the mechanical properties of 99.9% Al is significantly improved with increase of SiC and FeBx particles.

Abstract

Metal Matrisli kompozitler toz metalurjisi yöntemiyle üretilmişlerdir. Üretilen kompozitlerde FeBx in takviye oranları ağırlıkça 5, 10, 15, 20, 30, 40 ve SiC ün takviye oranları ağırlıkça 2.5, 5, 7.5, 10, 15, 20'tir. Al-FeBx ve Al-SiC kompozitleri 400 MPa basınçta sıkıştırılarak 10x10x55mm boyutlarında parçalar üretilmiştir. Daha sonra 600◦C'da 1 saat sinterlenmişlerdir. Yoğunluk, sertlik ve üç nokta eğme testleri gerçekleştirilmiştir. Test sonuçları SiC ve FeBx takviyelerinin oranlarının artmasıyla %99.9 Al'dan üretilen kompozitlerinin mekanik özelliklerinin arttığını göstermiştir.

🔖

Bu Makaleye Atıf Yap

Durmuş, H. (2009). PRODUCTION OF CERAMIC REINFORCED ALUMINUM COMPOSITE MATERIALS BY USING POWDER METALLURGY METHOD AND DETERMINATION OF ITS PROPERTIES. Engineering Sciences, Cilt: 4 Sayı: 3, 314–322. https://doi.org/10.12739/nwsaes.v4i3.5000067139

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...