KaydedilenlerDerginizi ekleyin

Dergiler / Sakarya University Journal of Science / 2026 / Volume: 23 Issue: 5

Production and Characterization of Carbon-Kevlar-Aramid Reinforced Layer Composites with VARTM Method

Yahya Taşgın(MUNZUR ÜNİVERSİTESİ)0000-0002-0902-336X
Engin Şahin(DEVLET SU İŞLERİ GENEL MÜDÜRLÜĞÜ)0000-0002-6238-0817
Sayfa
—
Yayın Tarihi
2019-10-01
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

It is obvious that the mechanical properties of carbon fiber reinforced samples yield better results.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, laminated composite materials are produced by Vacuum Assisted Resin Transfer Molding (VARTM) Method.
📊
Temel Bulgular & Veri:Three different reinforcement materials (carbon, kevlar and aramid) are used in the production phase.
💡
Sonuç & Katkı:It is obvious that the mechanical properties of carbon fiber reinforced samples yield better results.
🔬Tür:Research Article
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Kevlar · Carbon · Aramid Reinforcement

Abstract

In this study, laminated composite materials are produced by Vacuum Assisted Resin Transfer Molding (VARTM) Method. Three different reinforcement materials (carbon, kevlar and aramid) are used in the production phase. Tensile test is applied to the samples after the production and in the light of SEM images, fractured surfaces of the samples and their results are evaluated. It is obvious that the mechanical properties of carbon fiber reinforced samples yield better results.

🔖

Bu Makaleye Atıf Yap

Taşgın, Y., Şahin, E. (2019). Production and Characterization of Carbon-Kevlar-Aramid Reinforced Layer Composites with VARTM Method. Sakarya University Journal of Science, Volume: 23 Issue: 5. https://doi.org/10.16984/saufenbilder.550816

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Addington, Michelle and Daniel L. Schodek. 2005. Smart Materials and Technologies in Architecture. Retrieved April 25, 2017 (https://bintian. files.wordpress. com/2013/01/smart-materials-new-technologies-for-the architecture-design professions. pdf).
  2. Balikoğlu, Fatih, Akın Ataş, and Nurettin Arslan. 2012. “Yat ve Tekne İmalatında Vakum İnfüzyon Ile Kompozit Üretim Yönteminin Uygulanması.” Pp. 480–95 in 3. Ulusal Tasarım İmalat ve Analiz Kongresi.
  3. Gu, Yizhuo, Xuelin Tan, Zhongjia Yang, Min li, and Zuoguang Zhang. 2014. “Hot Compaction and Mechanical Properties of Ramie Fabric/epoxy Composite Fabricated Using Vacuum Assisted Resin Infusion Molding.” Materials and Design 56:852–61. Retrieved (http://dx.doi.org/10.1016/j.matdes.2013.11.077).
  4. İsmail, Durgun, Vatansever Onur, Ertan Rukiye, and Yavuz Nurettin. 2013. “Otomotiv Sektöründe Kullanılan Kompozit Parça İmalat Yöntemlerinin Deneysel Olarak Karşılaştırlması.” in II. Ulusal Ege Kompozit Malzemeler Sempozyumu.
  5. İsmail, Durgun, Vatansever Onur, Ertan Rukiye, and Yavuz Nurettin. 2014. “Polimer Esaslı Elyaf Takviyeli Kompozit Malzemelerde Üretim Tekniğinin Mekanik Özellikler Üzerindeki Etkisi.” in 7. Otomotiv Teknolojileri Kongresi. BURSA.
  6. İsmail Durgun. 2013. “Vakum İnfüzyon Yöntemi Ile Karbon Fiber Motor Kaput Üretimi.” in II. Ulusal Ege Kompozit Malzemeler Sempozyumu.
  7. Sevkat, Ercan and Malek Brahimi. 2011. “The Bearing Strength of Pin Loaded Woven Composites Manufactured by Vacuum Assisted Resin Transfer Moulding and Hand Lay-up Techniques.” Procedia Engineering 10:153–58. Retrieved (http://dx.doi.org/10.1016/j.proeng.2011.04.028).
  8. URL-1. 2017. “http://www.bilgiustam. com/kompozit-Malzemeler-Hakkında -Hersey/.” Retrieved April 25, 2017 (http://www.bilgiustam.com/?s=kompozit+malzemeler).
  9. URL-2. 2017. “http://www.kompozit. net/pinfo.asp?pid=287&diger=tumu.” Retrieved April 25, 2017 (http://www.kompozit.net/).
  10. Wang, Changchun, Guangquan Yue, Guanghui Bai, Lijian Pan, and Boming Zhang. 2016. “Compaction Behavior and Permeability Property Tests of Preforms in Vacuum-Assisted Resin Transfer Molding Using a Combined Device.” Measurement: Journal of the International Measurement Confederation 90:357–64. Retrieved (http://dx.doi.org/10.1016/j.measurement.2016.04.058).
  11. Zhang, Kaomin, Yizhuo Gu, Min li, and Zuoguang Zhang. 2014. “Effect of Rapid Curing Process on the Properties of Carbon Fiber/epoxy Composite Fabricated Using Vacuum Assisted Resin Infusion Molding.” Materials and Design 54:624–31. Retrieved (http://dx.doi.org/10.1016/j.matdes.2013.08.065).