KaydedilenlerDerginizi ekleyin

Dergiler / Sakarya University Journal of Science / 2020 / Volume: 24 Issue: 6

The Role of Vertical Tool Load on the Joint Properties of Friction Stir Spot Welded Brass Alloy

Zafer Barlas(SAKARYA UYGULAMALI BİLİMLER ÜNİVERSİTESİ, TEKNOLOJİ FAKÜLTESİ)0000-0001-9063-6501
Uğur Özsaraç(SAKARYA UYGULAMALI BİLİMLER ÜNİVERSİTESİ, TEKNOLOJİ FAKÜLTESİ)0000-0002-4806-1609
Sayfa
—
Yayın Tarihi
2020-12-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The temperature measurements show that the peak temperature increased with increasing tool load value..

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This study consisted of the effects of vertical tool load on failure value in FSSW of CuZn30.
📊
Temel Bulgular & Veri:The spot weld region was characterized by stir and heat-affected zones and these have various microhardness values ranging from 108.2 HV to 150.2 HV.
💡
Sonuç & Katkı:The temperature measurements show that the peak temperature increased with increasing tool load value..
🔬Tür:Research Article
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:FSSW · brass alloy · vertical tool load

Abstract

This study consisted of the effects of vertical tool load on failure value in FSSW of CuZn30. Tensile-shear test, microstructural examination, microhardness, vertical tool load, and temperature measurements were utilized to reveal the influence of FSSW process. According to the results, the tool load plays a key role on the features of joint. Not only low tool load, but also excessive load used leads to drop in the tensile-shear values. The spot weld region was characterized by stir and heat-affected zones and these have various microhardness values ranging from 108.2 HV to 150.2 HV. The temperature measurements show that the peak temperature increased with increasing tool load value..

🔖

Bu Makaleye Atıf Yap

Barlas, Z., Özsaraç, U. (2020). The Role of Vertical Tool Load on the Joint Properties of Friction Stir Spot Welded Brass Alloy. Sakarya University Journal of Science, Volume: 24 Issue: 6. https://ajindex.com/articles/1638490

Kaynakça (13)

  1. Z. Zhang, X. Yang, J. Zhang, G. Zhou, X. Xu, B. Zou, “Effect of welding parameters on microstructure and mechanical properties of friction stir spot welded 5052 aluminum alloy”, Materials and Design, vol. 32, no. 8–9, pp. 4461–4470, 2011.
  2. S. F Tebyani, K. Dehghani, “Effects of SiC nanopowders on the mechanical properties and microstructure of interstitial free steel joined via friction stir spot welding”, Materials and Design, vol. 90, pp. 660–668, 2016.
  3. Z. Shen, Y. Ding & A. P. Gerlich, “Advances in friction stir spot welding”, Critical Reviews in Solid State and Material Sciences, pp. 1–79, 2019.
  4. M. Li, C. Zhang, D. Wang, L. Zhou, D. Wellmann and Y. Tian, “Friction Stir Spot Welding of Aluminum and Copper: A Review”, Materials, vol. 13, no. 156, pp. 1–23, 2020.
  5. C. Jonckheere, B. D. Meester, C. Cassiers, M. Delhate, A. Simar, “Fracture and mechanical properties of friction stir spot welds in 6063-T6 aluminum alloy”, International Journal of Advanced Manufacturing Technology, vol. 62, pp. 569–575, 2012.
  6. Y. Tozaki, Y. Uematsu, K. Tokaji, “Effect of tool geometry on microstructure and static strength in friction stir spot welded aluminium alloys”, International Journal of Machine Tools and Manufacture, vol. 47, no. 15, pp. 2230–2236, 2007.
  7. R. Sarkar, T. K. Pal, and M. Shome, “Microstructures and properties of friction stir spot welded DP590 dual phase steel sheets”, Science and Technology of Welding and Joining, vol. 19, pp. 436–442, 2014.
  8. C.C. P Mazzaferro, T. S. Rosendo, M. A. D Tier, J. A. E. Mazzaferro, J. F. Dos Santos, T. R. Strohaecker, “Microstructural and Mechanical Observations of Galvanized TRIP Steel after Friction Stir Spot Welding”, Materials and Manufacturing Processes, vol. 30, pp. 1090–1103, 2015.
  9. A. K. Lakshminarayanan, V. E. Annamalai, K. Elangovan, “Identification of optimum friction stir spot welding process parameters controlling the properties of low carbon automotive steel joints”, Journal of Materials Research and Technology, vol. 4, no. 3, pp. 262–272, 2015.
  10. Z. Barlas, “Weldability of CuZn30 Brass/DP600 Steel Couple by Friction Stir Spot Welding” Acta Physica Polonica A, vol. 132, pp. 991–993, 2017.
  11. Z. Barlas, “Effect of friction stir spot weld parameters on Cu/CuZn30 bimetal joints”, International Journal of Advanced Manufacturing Technology, vol. 80, pp. 161–170, 2015.
  12. F. A. Garcia-Castillo, L. A. Reyes, C. Garza, O. E. Lopez-Botello, G. M. Hernandez-Munoz, and P. Zambrano-Robledo, “Investigation of Microstructure, Mechanical Properties, and Numerical Modeling of Ti6Al4V Joints Produced by Friction Stir Spot Welding”, Journal of Materials Engineering and Performance, vol. 29, no. 6, pp. 4105–4116, 2020.
  13. C.C. P Mazzaferro, T. S. Rosendo, M. A. D Tier, J. A. E. Mazzaferro, J. F. Dos Santos, T. R. Strohaecker, “Microstructural and Mechanical Observations of Galvanized TRIP Steel after Friction Stir Spot Welding”, Materials and Manufacturing Processes, vol. 30, pp. 1090–1103, 2015.