KaydedilenlerDerginizi ekleyin

Dergiler / Sakarya University Journal of Science / 2025 / Volume: 29 Issue: 6

Investigation of Wear Behavior of TiC Additive Stainless Steel Coatings Produced by High Pressure Cold Spray Method

Olcay Kaya(SAKARYA UNIVERSITY)0000-0000-0000-0000
Salih Gül(SAKARYA UNIVERSITY)0000-0000-0000-0001
Ediz Ercenk(SAKARYA UNIVERSITY)0000-0002-6792-1248
Sayfa
—
Yayın Tarihi
2025-12-23
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Furthermore, the hardness values were obtained in the range of 256-391 HV depending on the TiC addition.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, commercial 430L stainless steel powder and TiC powder were mixed in specific proportions.
📊
Temel Bulgular & Veri:The prepared powders were coated onto steel substrates using the high-pressure cold spray method (HPCS).
💡
Sonuç & Katkı:Furthermore, the hardness values were obtained in the range of 256-391 HV depending on the TiC addition.
🔬Tür:Research Article
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Cold Sprey · Stainless steel · TiC

Abstract

In this study, commercial 430L stainless steel powder and TiC powder were mixed in specific proportions. The prepared powders were coated onto steel substrates using the high-pressure cold spray method (HPCS). Micro-hardness and surface roughness measurements were performed after coating. The resulting materials were examined using an optical microscope and a scanning electron microscope (SEM) for microstructural analysis. X-ray diffraction analysis (XRD) was used for phase analysis. Furthermore, the coatings were abraded to the ball-on-disc wear level, and wear scars were analyzed using SEM and energy dispersive X-ray Spectroscopy (EDS) to investigate wear mechanisms. The results indicate that TiC addition increases hardness and wear resistance. The wear rates were obtained in the range of 1.24-1.57 mm3/Nm with increasing TiC addition. Changes in wear mechanisms were also detected with increasing TiC addition. Furthermore, the hardness values were obtained in the range of 256-391 HV depending on the TiC addition.

🔖

Bu Makaleye Atıf Yap

Kaya, O., Gül, S., Ercenk, E. (2025). Investigation of Wear Behavior of TiC Additive Stainless Steel Coatings Produced by High Pressure Cold Spray Method. Sakarya University Journal of Science, Volume: 29 Issue: 6. https://doi.org/10.16984/saufenbilder.1769220

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. V. K. Champagne, O. C. Ozdemir, A. Nardi, Practical Cold Spray, Springer, 2021.
  2. A. Moridi, S. M. Hassani-Gangaraj, M. Guagliano, M. Dao, “Cold spray coating: Review of material systems and future perspectives,” Surface Engineering, vol. 36, no. 6, pp. 369–395, 2014.
  3. E. Tekin, S. Uyum, B. Karahan, K. C. Tekin, U. Malayoğlu, “Soğuk püskürtme teknolojisi ve uygulamaları,” Mühendis ve Makina, vol. 62, no. 702, pp. 106–150, 2021.
  4. H. Assadi, H. Kreye, F. Gärtner, T.J.A.M. Klassen, “Cold spraying–A materials perspective,” Acta Materialia, vol. 116, pp. 382-407, 2016.
  5. Y. Wei, W. Zhang, J. Zhang, Y. Wang, X. Chu, S. Qi, et al., “Preparation of highly dense Ti-based coatings with enhanced corrosion protection performance via cold spray,” Surface and Coatings Technology, vol. 473, p. 130002, 2023.
  6. M. R. Rokni, S. R. Nutt, C. A. Widener, “Review of Relationship between Particle Deformation, Coating Microstructure, and Properties in High-Pressure Cold Spray,” Journal of Thermal Spray Techology, vol. 26, pp. 1308–1355, 2017.
  7. M. Ashokkumar, D. Thirumalaikumarasamy, P. Thirumal, R. Barathiraja, “Influences of Mechanical, Corrosion, erosion and tribological performance of cold sprayed Coatings A review,” Materials Today: Proceedings, vol. 46, pp. 7581-7587, 2021.
  8. K. Kılıçay, “A practical approach to fabrication of nano-Al2O3 reinforced MMC coatings by cold spray: Characterization of nanomechanical and tribological performance,” Materials Today Communications, vol. 39, p. 109257, 2024.
  9. A. Sai Jagadeeswara, S. Kumara, B. Venkataramanb, P. Suresh Babua, A. Jyothirmayi, “Effect of thermal energy on the deposition behaviour, wear and corrosion resistance of cold sprayed Ni-WC cermet coatings,” Surface and Coatings Technology, vol. 399, p. 126138, 2020.
  10. D. I. Adebiyi, A. P. I. Popoola, I. Botef, “Low pressure cold spray coating of Ti-6Al-4V with SiC-based cermet,” Materials Letters, vol. 175, pp. 63-67, 2016.
  11. G. Santacruz, Vicente Albaladejo, A. Silvello, R. F. Vaz, C. P´erez Bergmann, I. G. Cano, “The critical role of liquid surface tension in determining cavitation erosion and dry wear performance of WC-17Co coatings produced by cold spray technology,” Tribology International, vol. 208, p. 110609, 2025.
  12. J. Selvaraj, K. Balakrishnan, K. Raja, I. Charit, V. “Subramanian, A comparative review on cold sprayed cermet coatings and their applications in high temperature corrosion, oxidation and wear resistance,” Results in Surfaces and Interfaces, vol. 20, p. 100589, 2025.
  13. Z. Eyvazi, A. Abdollah-zadeh, R.A. Seraj, A. Azarniya, “Effect of SiC content on the microstructure and wear behavior of cold-sprayed Al-SiC coatings deposited on AZ31 alloy substrate,” Surface and Coatings Technology, vol. 489, p. 131170, 2024.