KaydedilenlerDerginizi ekleyin

Dergiler / The Eurasia Proceedings of Science Technology Engineering and Mathematics / 2026 / Volume: 11

Investigation of the Effect of Varying Laser Scribe Sizes on the Adhesion Performance of the Aa2024-T3/Cfrp Joints Depending on the Number of Laser Scan Repeats

Seda Aybalık(Kocaeli University)
Onur Coban(Kocaeli University)
Mustafa Ozgur Bora(Kocaeli University)
Erhan Akman(Kocaeli University)
Belgin Genc Oztoprak(Kocaeli University)
Sayfa
—
Yayın Tarihi
2020-12-31
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The observed failure modes on both the adherend surfaces have demonstrated that the mechanical interlocking mechanism between the adhesive and laser textured aluminum adherend with optimized scan repeat number has been well-worked.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:One of the laser surface treatment parameters of “scan repeat number” was optimized for the adhesion performance of AA2024-T3/CFRP joints according to the variation of laser scribe sizes.
📊
Temel Bulgular & Veri:Laser surface structuring was performed with previously optimized laser machine parameters from 1 to 9 “scan repeat number”.
💡
Sonuç & Katkı:The observed failure modes on both the adherend surfaces have demonstrated that the mechanical interlocking mechanism between the adhesive and laser textured aluminum adherend with optimized scan repeat number has been well-worked.
🔬Tür:Conference Paper
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Laser treatment · Adhesive bonding · AA2024-T3

Abstract

One of the laser surface treatment parameters of “scan repeat number” was optimized for the adhesion performance of AA2024-T3/CFRP joints according to the variation of laser scribe sizes. Laser surface structuring was performed with previously optimized laser machine parameters from 1 to 9 “scan repeat number”. After laser surface treatments with the increased scan repeat number, the characterization of the substrate was established by surface morphology and the dimensions of laser scribes. The adhesive bonding of laser-treated AA2024-T3 and untreated CFRP was applied and single-lap shear tests were then performed. The fracture surfaces of substrates were observed and analyzed to determine failure modes. The results indicated that laser scribe geometrical parameters have a significant effect on the adhesion performance of AA2024-T3/CFRP joints. The adhesive bonding strength was enhanced and the maximum value was 26.48 MPa (with 5 scan repetition) increasing by 39% compared to the adhesive joints without surface treatment of AA2024-T3 adherend. The observed failure modes on both the adherend surfaces have demonstrated that the mechanical interlocking mechanism between the adhesive and laser textured aluminum adherend with optimized scan repeat number has been well-worked.

🔖

Bu Makaleye Atıf Yap

Aybalık, S., Coban, O., Bora, M. O., Akman, E., Oztoprak, B. G. (2020). Investigation of the Effect of Varying Laser Scribe Sizes on the Adhesion Performance of the Aa2024-T3/Cfrp Joints Depending on the Number of Laser Scan Repeats. The Eurasia Proceedings of Science Technology Engineering and Mathematics, Volume: 11. https://ajindex.com/articles/1551366

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (9)

  1. Alfano, M. Lubineau G., Furgiuele F., Paulino G.H. (2012). Study on the role of laser surface irradiation on damage and decohesion of Al/Epoxy joints. International Journal of Adhesion and Adhesives, 39, 33–41.
  2. Bora, M.O., Çoban, O., Akman, E., Genc Oztoprak, B., Kutluk, T., (2020). Comparison of novel surface treatments of Al 2024 alloy for Al/CFRP adhesive bonded joints. International Journal of Adhesion and Adhesives, 103, 102721.
  3. Ebnesajjad S. (2014). Surface treatment of materials for adhesive bonding (Second Edition), Elsevier, Chapter 5. ISBN: 978-0-323-26435-8, USA.
  4. Feng Z., Zhao H., Tan C., Chen B., Song X., Feng J. (2020). Influence of laser process parameters on the characteristic of 30crmnsia steel substrate and adhesively bonded joints. Optics and Laser Technology, 123, 105920.
  5. Kwakernaak, A. (2012). Improvements in bonding metals for aerospace and other applications. Woodhead Publishing Limited.
  6. Rodríguez-Vidal, E., Lambarri J., Soriano C., Sanz C., Verhaeghe G. (2014). A combined experimental and numerical approach to the laser joining of hybrid polymer – Metal parts. Physics Procedia, 56, 835 – 844.
  7. Singh, H.K., (2004). Determining interfecial adhesion performance and realiability for microelectronic applications using a wedge test method. Master's Thesis, Virgina Polytechnic Institute And State University.
  8. Sugioka, K., Meunier, M., Pique, A. (2010). Laser Precision Microfabrication, 135, New York: Springer.
  9. Wu, L.H., Xiao B.L., Nagatsuka K., Nakataa K., &v Ma Z.Y. (2020). Achieving strong friction lap joints of carbon-fiber reinforced plastic and metals by modifying metal surface structure via laser-processing pretreatment. Composite Structures, 242, 112167.