Dergiler / Journal of Advances in Manufacturing Engineering / 2024 / Volume: 5 Issue: 2

Effect of strain rate on the tensile properties of 3D – printed pla specimens with fused deposition modelling

Sara Altahir(Abdullah Gül Üniverstesi)0009-0000-1520-2279
Roaa Gomaa(Abdullah Gül Üniverstesi)0009-0002-2580-7794
Cagatay Yilmaz(Abdullah Gül Üniversitesi)0000-0002-8063-151X
Sayfa
—
Yayın Tarihi
2024-12-31
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

This research contributes valuable insights into the dynamic behavior of FDM-printed PLA under different strain rates, offering implications for material performance in applications requiring diverse loading conditions.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This research investigates the influence of strain rate on the tensile properties of Polylactic Acid (PLA) material fabricated through Fused Deposition Modeling (FDM) using Type V ASTM-D638 specimens.
📊
Temel Bulgular & Veri:Three distinct strain rates (0.8 mm/min, 2 mm/min, and 20 mm/min) are considered, and Digital Image Correlation (DIC) is employed for ultimate tensile strain analysis.
💡
Sonuç & Katkı:This research contributes valuable insights into the dynamic behavior of FDM-printed PLA under different strain rates, offering implications for material performance in applications requiring diverse loading conditions.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:638 specimens
⚙️Değişkenler:Strain rate · fused deposition modeling (FDM) · polylactic acid (PLA)

Abstract

This research investigates the influence of strain rate on the tensile properties of Polylactic Acid (PLA) material fabricated through Fused Deposition Modeling (FDM) using Type V ASTM-D638 specimens. Three distinct strain rates (0.8 mm/min, 2 mm/min, and 20 mm/min) are considered, and Digital Image Correlation (DIC) is employed for ultimate tensile strain analysis. The methodology involves CAD modeling, 3D printing, surface preparation, and tensile testing, with DIC analysis performed using the Ncorr application. Results indicate a linear increase in tensile strength with higher strain rates, however, Young's modulus decreases with increasing strain rate. The study also observes a significant decrease in ultimate strain with higher strain rates. This research contributes valuable insights into the dynamic behavior of FDM-printed PLA under different strain rates, offering implications for material performance in applications requiring diverse loading conditions.

🔖

Bu Makaleye Atıf Yap

Altahir, S., Gomaa, R., Yilmaz, C. (2024). Effect of strain rate on the tensile properties of 3D – printed pla specimens with fused deposition modelling. Journal of Advances in Manufacturing Engineering, Volume: 5 Issue: 2. https://ajindex.com/articles/1504997

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (27)

  1. Wong, K. K. V., & Hernandez, A. (2012). A review of additive manufacturing. ISRN Mechanical Engineering, 2012, Article 208760. [CrossRef]
  2. Singh, R., Singh, J., & Singh, S. (2016). Investigation for dimensional accuracy of AMC prepared by FDM assisted investment casting using nylon-6 waste based reinforced filament. Measurement, 78, 253–259. [CrossRef]
  3. Kristiawan, R., Imaduddin, F., Ariawan, D., Sabino, U., & Arifin, Z. (2021). A review on the fused deposition modeling (FDM) 3D printing: Filament processing, materials, and printing parameters. Open Engineering, 11, 639–649. [CrossRef]
  4. Ali, S., Abdallah, S., Devjani, D., John, J., Samad, W. A., & Pervaiz, S. (2022). Effect of build parameters and strain rate on mechanical properties of 3D printed PLA using DIC and desirability function analysis. Rapid Prototyping Journal, 29, 92111. [CrossRef]
  5. Hodzic, D., Pandžić, A., Hajro, I., & Tasić, P. (2020). Strain rate influence on mechanical characteristics of FDM 3D printed materials (pp. 168–175). Proceedings of the 31st International DAAAM Symposium 2020. [CrossRef]
  6. Vidakis, N., Petousis, M., Velidakis, E., Liebscher, M., Mechtcherine, V., & Tzounis, L. (2020). On the strain rate sensitivity of fused filament fabrication (FFF) processed PLA, ABS, PETG, PA6, and PP thermoplastic polymers. Polymers, 12, Article 2924. [CrossRef]
  7. Ergene, B., & Bolat, Ç. (2022). An experimental investigation on the effect of test speed on the tensile properties of the PETG produced by additive manufacturing. International Journal of 3D Printing Technologies and Digital Industry, 6. [CrossRef]
  8. Wang, K., Xie, X., Wang, J., Zhao, A., Peng, Y., & Rao, Y. (2020). Effects of infill characteristics and strain rate on the deformation and failure properties of additively manufactured polyamide-based composite structures. Results in Physics, 18, Article 103346. [CrossRef]
  9. Wang, Y., Li, X., Chen, Y., & Zhang, C. (2021). Strain rate dependent mechanical properties of 3D printed polymer materials using the DLP technique. Additive Manufacturing, 47, Article 102368. [CrossRef]
  10. Hibbert, K., Warner, G., Brown, C., Ajide, O. O., Owolabi, G., & Azimi, A. (2019). The effects of build parameters and strain rate on the mechanical properties of FDM 3D-printed acrylonitrile butadiene styrene. Open Journal of Organic Polymer Materials, 9, 1–27. [CrossRef]
  11. Sagias, V., Giannakopoulos, K. I., & Stergiou, C. (2018). Mechanical properties of 3D printed polymer specimens. Procedia Structural Integrity, 10, 85–90. [CrossRef]
  12. Elmrabet, N., & Siegkas, P. (2020). Dimensional considerations on the mechanical properties of 3D printed polymer parts. Polymer Testing, 90, Article 106656. [CrossRef]
  13. Rohbeck, N., Ramachandramoorthy, R., Casari, D., Schürch, P., Edwards, T. E. J., Schilinsky, L.,. & Michler, J. (2020). Effect of high strain rates and temperature on the micromechanical properties of 3D-printed polymer structures made by two-photon lithography. Materials & Design, 195, Article 108977. [CrossRef]
  14. Vanaei, H., El Magri, A., Rastak, M., Vanaei, S., Vaudreuil, S., & Tcharkhtchi, A. (2022). Numerical–experimental analysis toward the strain rate sensitivity of 3D-printed nylon reinforced by short carbon fiber. Materials, 15, Article 8722. [CrossRef]
  15. Cai, R., Lin, H., Cheng, P., Zhang, Z., Wang, K., & Peng, Y., … & S. Ahzi. (2022). Investigation on dynamic strength of 3D‐printed continuous ramie fiber reinforced biocomposites at various strain rates using machine learning methods. Polymer Composites, 43, pp. 52355249. [CrossRef]
  16. Lai, C. Q., Markandan, K., Luo, B., Lam, Y., Chung, W., & Chidambaram, A. (2020). Viscoelastic and high strain rate response of anisotropic graphene-polymer nanocomposites fabricated with 3D stereolithography printing. Additive Manufacturing, 37, Article 101721. [CrossRef]
  17. Baligidad, S., Gangadhara, C., & Chandrashekhar, M. (2021). Investigation on strain rate sensitivity of 3D printed sPEEK-HAP/rGO composites. Research Square. doi: 10.21203/rs.3.rs-1125996/v1 [CrossRef]
  18. Fisher, T., Almeida, H. Jr., Falzon, B. G., & Kazancı, Z. (2023). Tension and compression properties of 3D-printed composites: Print orientation and strain rate effects. Polymers, 15, Article 1708. [CrossRef]
  19. Hosseini, S. A., Torabizadeh, M., & Eisazadeh, H. (2023). Experimental study of the effect of strain rate on the mechanical behavior of assorted thermoplastic polymers. Journal of Materials Engineering and Performance, 33, 69426951. [CrossRef]
  20. Wang, K., Xie, G., Xiang, J., Li, T., Peng, Y., & Wang, J., et al. (2022). Materials selection of 3D printed polyamide-based composites at different strain rates: A case study of automobile front bumpers. Journal of Manufacturing Processes, 84, 1449–1462. [CrossRef]
  21. Patanwala, H., Hong, D., Vora, S., Bognet, B., & Ma, A. (2017). The microstructure and mechanical properties of 3D printed carbon nanotube-polylactic acid composites. Polymer Composites, 39(Suppl 2), E1060E1071. [CrossRef]
  22. Mahmoudi, M., Burlison, S., Moreno, S., & Minary-Jolandan, M. (2021). Additive-free and support-free 3D printing of thermosetting polymers with isotropic mechanical properties. ACS Applied Materials & Interfaces, 13, 5529–5538. [CrossRef]
  23. ASTM International. (2014). ASTM D638-14 Standard test methods for tensile properties of plastic. America Society for Testing and Material. ASTM International.
  24. Yilmaz, C., Ali, H. Q., & Yildiz, M. (2022). Application of classical lamination theory to fused deposition method 3-D printed plastics and full field surface strain mapping. Afyon Kocatepe Üniversitesi Fen ve Mühendislik Bilimleri Dergisi, 22, 342–352. [CrossRef]
  25. eSUN. (Aug 21, 2024). PLA+, https://www.esun3d.com/pla-pro-product/
  26. Bolat, Ç., & Ergene, B. (2022). An investigation on dimensional accuracy of 3D printed PLA, PET-G and ABS samples with different layer heights. Çukurova Üniversitesi Mühendislik Fakültesi Dergisi, 37, 449–458. [CrossRef]
  27. Rohbeck, N., Ramachandramoorthy, R., Casari, D., Schürch, P., Edwards, T. E. J., Schilinsky, L.,. & Michler, J. (2020). Effect of high strain rates and temperature on the micromechanical properties of 3D-printed polymer structures made by two-photon lithography. Materials & Design, 195, Article 108977. [CrossRef]