KaydedilenlerDerginizi ekleyin

Dergiler / International Journal of 3D Printing Technologies and Digital Industry / 2026 / Cilt: 7 Sayı: 1

PRODUCTION OF WASTE JUTE DOPED PLA (POLYLACTIC ACID) FILAMENT FOR FFF: EFFECT OF PULVERIZATION

Ayberk Sözen(DOKUZ EYLUL UNIVERSITY, INSTITUTE OF MARITIME SCIENCES AND TECHNOLOGY, DEPARTMENT OF MARINE TECHNOLOGY)0000-0002-9657-5567
Alperen Doğru(EGE UNIVERSITY, AVIATION VOCATIONAL SCHOOL)0000-0003-3730-3761
Murat Demir(DOKUZ EYLUL UNIVERSITY, FACULTY OF ENGINEERING)0000-0001-8670-5412
Havva Nur Özdemir(DOKUZ EYLUL UNIVERSITY, FACULTY OF SCIENCE, DEPARTMENT OF CHEMISTRY)0000-0002-0630-7340
Yasemin Seki(DOKUZ EYLUL UNIVERSITY, FACULTY OF ENGINEERING)0000-0002-9267-922X
Sayfa
124–128
Yayın Tarihi
2023-04-29
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Within the scope of the study, it is aimed to reveal the material size effect for producing natural fiber-reinforced filaments for additive manufacturing.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In recent years, there has been an outbreak of research on natural fiber-reinforced materials to reduce non-recycled material effects and produce environmentally friendly products.
📊
Temel Bulgular & Veri:In parallel with the increasing popularity of additive manufacturing, the development of new natural fiber-reinforced materials in this field has also increased to improve pure material characteristics and reduce raw materials usage.
💡
Sonuç & Katkı:Within the scope of the study, it is aimed to reveal the material size effect for producing natural fiber-reinforced filaments for additive manufacturing.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:PLA · Jute · Additive Manufacturing

Abstract

In recent years, there has been an outbreak of research on natural fiber-reinforced materials to reduce non-recycled material effects and produce environmentally friendly products. In parallel with the increasing popularity of additive manufacturing, the development of new natural fiber-reinforced materials in this field has also increased to improve pure material characteristics and reduce raw materials usage. This study presents the manufacturing process of %5 waste jute-reinforced PLA filaments and the characteristics of 3D printed parts. For the production of jute-reinforced filaments, polylactic acid (PLA) granules were pulverized to increase the material surface for better bonding between materials in the composite matrix structure. The effectiveness of pulverizing PLA granules was exposed by comparing it with the production of the same composite matrix with PLA granules. Both matrices were formed into filaments to produce 3D parts in Fused Filament Fabrication technology. Thermo-gravimetric analysis (TGA) and differential scanning calorimetry (DSC) will be presented in filament form. Besides, the mechanical properties of 3D parts will also be presented. Within the scope of the study, it is aimed to reveal the material size effect for producing natural fiber-reinforced filaments for additive manufacturing.

🔖

Bu Makaleye Atıf Yap

Sözen, A., Doğru, A., Demir, M., Özdemir, H. N., Seki, Y. (2023). PRODUCTION OF WASTE JUTE DOPED PLA (POLYLACTIC ACID) FILAMENT FOR FFF: EFFECT OF PULVERIZATION. International Journal of 3D Printing Technologies and Digital Industry, Cilt: 7 Sayı: 1, 124–128. https://doi.org/10.46519/ij3dptdi.1213659

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (11)

  1. Dip, T. M.; Emu. A. S.; Nafiz, M. N. H.; Kundu, P.; Rakhi, H. R.; Sayam, A.; Akhtarujjman, Md.; Shoaib, M.; Ahmed, M. S.; Ushno, S. T. et al., “3D printing technology for textiles and fashion.” Textile Progress, Vol. 52, Issue 4, Pages 167-260, 2020
  2. Royan, N. R., Leong, J. S., Chan, W. N., Tan, J. R., & Shamsuddin, Z. S. B. “Current state and challenges of natural fibre-reinforced polymer composites as feeder in fdm-based 3D printing.” Polymers, Vol. 13, Issue 14, 2289, 2021.
  3. Deb, D., Jafferson, J.M., “Natural fibers reinforced FDM 3D printing filaments.” Materials Today:Proceedings. Vol. 46, Issue 2, Pages 1308-1318, 2021.
  4. Kariz, M., Sernek, M., Obucina, M., Kuzman, M.K., “Effect of wood content in FDM filament on properties of 3D printed parts.” Materials Today:Communications. Vol. 14, Pages 135-140, 2018.
  5. Petchwatta, N., Channuan, W., Naknaen, P., Narupai, B., “3D Printing Filaments Prepared from Modified Poly(Lactic Acid)/ Teak Wood Flour Composites: An Investigation on the Particle Size Effects and Silane Coupling Agent Compatibilisation.” Journal of Physical Science. Vol.30, Issue 2, Pages 169-188, 2019.
  6. Filgueira, D., Holmen, S., Melboss, J.K., Moldes, D., Echtermeyer, A.T., Chinga-Carrasco, G., “Enzymatic-Assisted Modification of Thermomechanical Pulp Fibers To Improve the Interfacial Adhesion with Poly(lactic acid) for 3D Printing.” ACS Sustainable Chem. Eng., Vol. 5, Issue 10, Pages 9338-9346, 2017.
  7. Le Duigou, A., Barbe, A., Guillou, E., Castro, M., “3D printing of continuous flax fibre reinforced biocomposites for structural applications.” Materials & Design, Vol. 180, 107884. 2019.
  8. Gama, N., Magina, S., Ferreira, A., Barros-Timmons, A., “Chemically modified bamboo fiber/ABS composites for high-quality additive manufacturing.” Polymer Journal. Vol. 53, Pages 1459-1467., 2021.
  9. Long, Y., Zhang, Z., Fu, K., Li, Y., “Efficient plant fibre yarn pre-treatment for 3D printed continuous flax fibre/poly(lactic) acid composites.” Composites Part B:Engineering. Vol. 227, 109389, 2021.
  10. Lacerda, P.S.S., Gama, N., Freire, C.S.R., Silvestre, A.J.D., Barros-Timmons, A., “Grafting Poly(Methyl Methacrylate) (PMMA) from Cork via Atom Transfer Radical Polymerization (ATRP) towards Higher Quality of Three-Dimensional (3D) Printed PMMA/Cork-g-PMMA” Materials. Vol. 12, Issue 9, 1867, 2020.
  11. Dip, T. M.; Emu. A. S.; Nafiz, M. N. H.; Kundu, P.; Rakhi, H. R.; Sayam, A.; Akhtarujjman, Md.; Shoaib, M.; Ahmed, M. S.; Ushno, S. T. et al., “3D printing technology for textiles and fashion.” Textile Progress, Vol. 52, Issue 4, Pages 167-260, 2020