KaydedilenlerDerginizi ekleyin

Dergiler / Sigma Mühendislik ve Fen Bilimleri Dergisi / 2026 / Volume: 36 Issue: 3

OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING

Kürşad Oğuz Oskay(Cumhuriyet University, Dep. of Metallurgical and Materials Eng)0000-0003-4026-867X
Bilal Demirel(Erciyes University, Dep. of Metarials Science and Eng)
Sayfa
—
Yayın Tarihi
2018-09-01
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:NiCrAl composite coatings were obtained by electro-deposition under direct current (DC) conditions from a Watt’s bath containing suspended Cr, Al particles.
📊
Temel Bulgular & Veri:Mathematical models were developed to simulate the electroplated composite coating.
💡
Sonuç & Katkı:Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Electrodeposition · NiCrAl composite coating · RSM

Abstract

NiCrAl composite coatings were obtained by electro-deposition under direct current (DC) conditions from a Watt’s bath containing suspended Cr, Al particles. Mathematical models were developed to simulate the electroplated composite coating. The models allow composition of the coatings to be predicted. The predicted values obtained were close to the experimental values, indicating the suitability of the models. The prediction made using Response Surface Method (RSM) was also supported by SEM photos. Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.

🔖

Bu Makaleye Atıf Yap

Oskay, K. O., Demirel, B. (2018). OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. Sigma Mühendislik ve Fen Bilimleri Dergisi, Volume: 36 Issue: 3. https://ajindex.com/articles/1345075

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (17)

  1. Aruna S. T., Roy S., Sharma A., Savitha G., and Grips V. K. W. (2014) Cost-effective wear and oxidation resistant electrodeposited Ni – pumice coating, Surf. Coat. Technol., vol. 251, pp. 201–209.
  2. Masoudi M., Hashim M., Kamari H. M., and Salit M. S. (2012) Fabrication and characterization of Ni–SiC–Cr nanocomposite coatings, Appl. Nanosci., vol. 3, no. 4, pp. 357–362.
  3. Liu H. and Chen W. (2005) Electrodeposited Ni-Al composite coatings with high Al content by sediment co-deposition, Surf. Coatings Technol., vol. 191, no. 2–3, pp. 341–350.
  4. Borkar T. and Harimkar S. P. (2011) Effect of electrodeposition conditions and reinforcement content on microstructure and tribological properties of nickel composite coatings, Surf. Coatings Technol., vol. 205, no. 17–18, pp. 4124–4134.
  5. Vaezi M. R., Sadrnezhaad S. K., and Nikzad L. (2008) Electrodeposition of Ni–SiC nano-composite coatings and evaluation of wear and corrosion resistance and electroplating characteristics, Colloids Surfaces A Physicochem. Eng. Asp., vol. 315, no. 1–3, pp. 176–182.
  6. Srivastava M., Siju, Balaraju J. N., and Ravisankar B. (2015) Development and High Temperature Property Evaluation of Ni-Co-Cr-Al Composite Electroforms, J. Mater. Eng. Perform., vol. 24, no. 5, pp. 1937–1944.
  7. Ul-Hamid A., Dafalla H., Al-Yousef F., and Mohammed A. I. (2014) Microstructural study of NiCrAlY electrodeposits, Prot. Met. Phys. Chem. Surfaces, vol. 50, no. 5, pp. 679–687.
  8. Bahamirian M. (2013) An Investigation on Effect of Bond Coat Replacement on Hot Corrosion Properties of Thermal Barrier Coatings, Iran. J. Mater. Sci. Eng., vol. 10, no. 3, pp. 12–21.
  9. Bates B. L., Zhang L. Z., and Zhang,Y. (2015) Electrodeposition of Ni matrix composite coatings with embedded CrAlY particles, Surf. Eng., vol. 31, no. 3, pp. 202–208.
  10. Haynes J. A., Ferber M. K., and Porter W. D. (2000) Thermal Cycling Behavior of Plasma-Sprayed Thermal Barrier Coatings with Various MCrAIX Bond Coats, J. Therm. Spray Technol., vol. 9, no. March, pp. 38–48.
  11. Zhu C., Li P., and Wu X. Y. (2015) A study of the diffusion and pre-oxidation treatment on the formation of Al2O3 ceramic scale on NiCrAlY bond-coat during initial oxidation process, Ceram. Int., vol. 42, pp. 7708–7716,.
  12. Ajdelsztajn L., Tang F., Kim G. E., Provenzano V., and Schoenung J. M. (2005) Synthesis and Oxidation Behavior of Nanocrystalline MCrAlY Bond Coatings, J. Therm. Spray Technol., vol. 14, no. 1, pp. 23–30.
  13. Şahin Y. and Öksüz K. E. (2016) Tribological behavior of Al2O3/Al composite coating on γ-TiAl at elevated temperature, Mater. Test., vol. 58, no. 5, pp. 453–461.
  14. Aslan N. (2008) Multi-objective optimization of some process parameters of a multi-gravity separator for chromite concentration, Sep. Purif. Technol., vol. 64, no. 2, pp. 237–241.
  15. Zhao L.-C. et al. (2012) Response surface modeling and optimization of accelerated solvent extraction of four lignans from fructus schisandrae. Molecules, vol. 17, no. 4, pp. 3618–29.
  16. Lee H. K., Lee H.-Y., and Jeon J.-M. (2007) Codeposition of micro- and nano-sized SiC particles in the nickel matrix composite coatings obtained by electroplating, Surf. Coatings Technol. vol. 201, no. 8, pp. 4711–4717.
  17. Kim S. K. and Yoo H. J. (1998) Formation of bilayer Ni–SiC composite coatings by electrodeposition. Surf. Coatings Technol., vol. 108, pp. 564–569.