Dergiler / Mühendis ve Makina / 2026 / Cilt: 66 Sayı: 721

HAVACILIK UYGULAMALARINDA EMNİYET KAVRAMALARI İÇİN KOMPOZİT SÜRTÜNME MALZEMELERİNİN GELİŞTİRİLMESİ

DEVELOPMENT OF COMPOSITE FRICTION MATERIALS FOR SAFETY CLUTCHES IN AVIATION APPLICATIONS

Orhan Karabulut(Dönmez Debriyaj San. ve Tic. A.Ş.)0009-0001-0623-660X
Ceren Çelik(Dönmez Debriyaj San. ve Tic. A.Ş.)0009-0005-1835-6114
Caner Eş(Dönmez Debriyaj San. ve Tic. A.Ş.)0000-0002-8982-7789
Sedat Akkurt(IZMIR INSTITUTE OF TECHNOLOGY)0000-0002-2534-5756
Mücahit Sütçü(MANISA CELAL BAYAR UNIVERSITY)
Sayfa
606–625
Yayın Tarihi
2026-01-07
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Ayrıca alüminanın sürtünme katsayısı üzerinde kuvarstan daha önemli bir etkiye sahip olduğu sonucuna varılmıştır.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmada, sürtünme davranışı iyileştirilmiş kompozitler geliştirilmiştir.
📊
Temel Bulgular & Veri:Sürtünme ve aşınma davranışlarını değerlendirmek için bir bilye-disk aşınma test cihazı kullanılmıştır.
💡
Sonuç & Katkı:Ayrıca alüminanın sürtünme katsayısı üzerinde kuvarstan daha önemli bir etkiye sahip olduğu sonucuna varılmıştır.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Emniyet kavrama malzemesi · Kompozit balata üretimi · Sürtünme ve Aşınma

Özet

Bu çalışmada, sürtünme davranışı iyileştirilmiş kompozitler geliştirilmiştir. Sürtünme kavrama numuneleri, tozların karıştırılması, preslenmesi ve kürlenmesi gibi geleneksel yöntemlerle üretilmiştir. Sürtünme ve aşınma davranışlarını değerlendirmek için bir bilye-disk aşınma test cihazı kullanılmıştır. Kompozitlerin yüzey dağılımları, yüzey mikro yapı görüntüleri ile incelenmiştir. Farklı bileşenlerin kavrama performansı üzerindeki etkileri, optimum işlem parametreleri belirlenerek değerlendirilmiştir. Kuvars ve alümina içeren malzemelerin sürtünme katsayısını iyileştirdiği ve kavrama performansını artırdığı görülmüştür. Ayrıca alüminanın sürtünme katsayısı üzerinde kuvarstan daha önemli bir etkiye sahip olduğu sonucuna varılmıştır.

Abstract

In this study, composite with improved friction behavior were developed. Friction clutch samples were produced via conventional methods of mixing, pressing, and curing powders. A ball-on-disc wear tester was used to evaluate their friction and wear behavior. The surface distributions of the composites were examined by surface microstructure images. The effects of different components on clutch performance were evaluated by determining optimum process parameters. It was observed that materials containing quartz and alumina improved the friction coefficient and increased the clutch performance. It was also concluded that alumina has a more significant effect on the friction coefficient than quartz.

🔖

Bu Makaleye Atıf Yap

Karabulut, O., Çelik, C., Eş, C., Akkurt, S., Sütçü, M. (2026). HAVACILIK UYGULAMALARINDA EMNİYET KAVRAMALARI İÇİN KOMPOZİT SÜRTÜNME MALZEMELERİNİN GELİŞTİRİLMESİ. Mühendis ve Makina, Cilt: 66 Sayı: 721, 606–625. https://doi.org/10.46399/muhendismakina.1600524

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (33)

  1. Ain, Q. U., Wani, M. F., Sehgal, R., & Singh, M. K. (2024).Role of Al2O3 reinforcements in polymer-based nanocomposites for enhanced nanomechanical properties: Time-dependent modeling of creep and stress relaxation. Ceramics International, 50. Doi: https://doi.org/10.1016/j.ceramint.2024.06.201.
  2. Akdoğu, K. (2010). Ticari uçaklarda kullanılan fren balata malzemeleri (Master's thesis). Yildiz Technical University Institute of Science, İstanbul.
  3. Anto, T., Rejeesh, C.R. (2023). Synthesis and characterization of recycled HDPE polymer composite reinforced with nano-alumina particles. Materials Today: Proceeding, 72, 3177-3182. Doi: https://doi.org/10.1016/j.matpr.2022.11.190.
  4. Bezzazi, M., Khamlichi, A., Jabbouri, A., Reis, P., & Davim, J.P. (2007). Experimental characterization of frictional behaviour of clutch facings using Pin-on-disk machine." Materials & design 28.7 (2007): 2148-2153. Doi: https://doi.org/10.1016/j.matdes.2006.07.001.
  5. Bijwe, J. (1997). Composites as friction materials: Recent developments in non‐asbestos fiber reinforced friction materials—a review. Polymer Composites, 18 (3), 378-396. Doi: https://doi.org/10.1002/pc.10289.
  6. Borawski, A. (2020). Conventional and unconventional materials used in the production of brake pads– review. Science and Engineering of Composite Materials, 27 (1), 374-396. Doi: https://doi.org/10.1515/secm-2020-0041.
  7. Çolak, N. Y., & Turhan, H. (2016). Toz metalurjisi yöntemi ile üretilen Al-Si/B4C kompozit malzemenin mikroyapı ve mekanik özelliklerinin araştırılması. Fırat University Journal of Engineering Sciences, 28 (2), 259-266.
  8. Den Hartigh, E., Küçükönal, H., & Verheij, B. (2012). The Turkish aviation system and the strategy of Turkish Airlines. In Air Transport and Operations (pp. 231-246). IOS Press.
  9. Ertan, R. & Yavuz, N. (2006). Polimer matriksli fren balata malzemelerinin kompozisyon ve üretim parametreleri açısından değerlendirilmesi. Mühendis ve Makina, 47 (553), 24-30.
  10. Ertan, R. & Yavuz, N. (2011). The effects of graphite, coke and ZnS on the tribological and surface characteristics of automotive brake friction materials. Industrial Lubrication and Tribology, 63 (4), 245-253. Doi: https://doi.org/10.1108/00368791111140468.
  11. Geng, Z., & Li, G. (2022). Optimal clutch control of a one-way clutch assistant transmission for electrical vehicles. International Journal of Automotive Science And Technology, 6(3), 257-264. Doi: https://doi.org/10.30939/ijastech.1119271.
  12. Gümüş, E. (2012). Otomotivde kullanılan kompozit sürtünmeli fren balatalarında yerli uçucu kül katkısının balata özelliklerine etkisinin incelenmesi. Master's Thesis, Yildiz Technical University Institute of Science and Technology, İstanbul.
  13. Heino, V., Valtonen, K., Kivikytö-Reponen, P., Siitonen, P., & Kuokkala, V. T. (2013). Characterization of the effects of embedded quartz layer on wear rates in abrasive wear. Wear, 308(1-2), 174-179. Doi: https://doi.org/10.1016/j.wear.2013.06.019.
  14. Ibrahim, M. M., El-Tayeb, N. S. M., Shazly, M., & El-Sayed Seleman, M. M. (2024). An experimental study on the effect of graphite microparticles on the mechanical and tribological properties of epoxy matrix composites. Functional Composite Materials, 5(1), 2. Doi: https://doi.org/10.1186/s42252-023-00046.
  15. Kabataş, K., & Akgün, A. E. (2021). Yüksek teknoloji içeren sanayi kümelenmeleri: havacilik kümelenmeleri örneği. İşletme Ekonomi ve Yönetim Araştırmaları Dergisi, 4(2), 420-443. Doi: https://doi.org/10.33416/baybem.952476.
  16. Kahvecioglu, S., & Oktal, H. (2014). Turkish UAV capabilities as a new competitor in the market. International Journal of Intelligent Unmanned Systems, 2(3), 183-191. Doi: https://doi.org/10.1108/IJIUS-04-2014-0004.
  17. Kara, F. (2023). Triboloji nedir? uygulama alanları nerelerdir. Retrieved from: https://malzemebilimi.net/triboloji-nedir-uygulama-alanlari-nerelerdir.html, Last access date: 29.07.2024.
  18. Kenaroğlu, Y. (2013). İnsansız hava aracı: ne kadar güvenilir?. Mühendis ve Makina, (636).
  19. Kim, S. J., Kim, K. S., & Jang, H. (2003). Optimization of manufacturing parameters for a brake lining using Taguchi method. Journal of Materials Processing Technology, 136(1-3), 202-208. Doi: https://doi.org/10.1016/S0924-0136(03)00159-6.
  20. Li, Z., Qi, X., Liu, C., Fan, B., & Yang, X. (2023). Particle size effect of PTFE on friction and wear properties of glass fiber reinforced epoxy resin composites. Wear, 532, 205104.
  21. Lin, Z., Tao,P., Zhang, K., Zhao,X., Gao, B., Shan, Z., Chen, Z. & Zhang, Z. (2024). Regulating the severe running- in wear of polymer composites by a dual-pin- on-disk (DPOD) multicomponent approach. Wear, 554-555. Doi: https://doi.org/10.1016/j.wear.2024.205483.
  22. Nassar, A., Younis, M., Ismail, M. & Nassar, E. (2022). Improved wear-resistant performance of epoxy resin composites using ceramic particles. Polymers, 14(2), 333. Doi: https://doi.org/10.3390/polym14020333.
  23. Prabhakar, K., Debnath, S., Ganesan, R., & Palanikumar, K. (2018). A review of mechanical and tribological behaviour of polymer composite materials—a review. In IOP Conference Series: Materials Science and Engineering 344, 012015. Doi: https://doi.org/10.1088/1757-899X/344/1/01201.
  24. Ramesh, M. R., Ravindra, K. A., Ashok, B., & Kannan, C. (2021) Optimizing thermal performance of a dry rigid clutch by varying groove pattern and friction material. Materials Today: Proceedings 46: 7459-7467. Doi: https://doi.org/10.1016/j.matpr.2021.01.130.
  25. Rathaur, A. S., Patel, V. K., & Katiyar, J. K. (2019). Tribo-mechanical properties of graphite/talc modified polymer composite bearing balls. Materials Research Express, 7 (1). Doi: https:// doi.org/10.1088/2053-1591/ab58db.
  26. Rajak, D. K., Wagh, P. H., & Linul, E. (2021). Manufacturing technologies of carbon/glass fiber-reinforced polymer composites and their properties—a review. Polymers 13(21), 3721. Doi: https://doi.org/10.3390/polym13213721.
  27. Sugözü, İ., & Yavuz, İ. (2009). Fren balatası üretiminde toz karıştırma süresinin frenleme karakteristiğine etkisinin araştırılması. 5. Uluslararası İleri Teknolojiler Sempozyumu (IATS’09), Karabük.
  28. Temiz, V. (2014). Makina elemanları 1 triboloji genel bilgiler. Retrieved from: https://web.itu.edu.tr/temizv/Sunular/Triboloji.pdf, Last access date: 22.07.2024.
  29. Toros, M. (2011). Fren balatalarında nano malzemelerin kullanımının frenleme performansına etkilerinin deneysel araştırılması. (Master's Thesi). Selcuk University Institute of Science, Konya.
  30. Yanar, H., Ayar, H. H., Demirtas, M., & Purcek, G. (2020). Effect of resin content on tribological behavior of brake pad composite material. Industrial Lubrication and Tribology, 72(2), 195-202. Doi: https://doi.org/10.1108/ILT-05-2018-0171.
  31. Yılmaz, F. (2020). Türkiye’de sivil havacılık sektörünün tarihsel gelişimi ve 2003-2018 yılları arasında sektörün değerlendirilmesi. Avrasya Sosyal ve Ekonomi Araştırmaları, 7 (1), 113-129.
  32. Zurowski, W., Zepchło, J., Krzyzak, A., Gevorkyan, E., Rucki, M., Siek, E., & Białkowska, A. (2021). Wear resistance of the glass-fiber reinforced polymer composite with the addition of quartz filler. Materials, 14 (14), 3825. Doi: https:// doi.org/10.3390/ma14143825.
  33. Geng, Z., & Li, G. (2022). Optimal clutch control of a one-way clutch assistant transmission for electrical vehicles. International Journal of Automotive Science And Technology, 6(3), 257-264. Doi: https://doi.org/10.30939/ijastech.1119271.