KaydedilenlerDerginizi ekleyin

Dergiler / Ejovoc (Electronic Journal of Vocational Colleges) / 2026 / Cilt: 5 Sayı: 4

AN EXPERIMENTAL AND THEORITICAL STUDY ON THE PRESSURE DROP OF FLUID AT EXTRUSION PROCESS

İbrahim Savaş Dalmış
Ümit Güler
Alper Karakoca
Sait Özmen Eruslu
Sayfa
70–77
Yayın Tarihi
2015-12-28
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The results of power law model is found in good agreement with experimental results for outlet sections of process.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:This paper investigated the pressure drop during the extrusion processes.
📊
Temel Bulgular & Veri:The objectives of this investigation were to increase efficiency of plastic extrusion which plastic equipment produced.
💡
Sonuç & Katkı:The results of power law model is found in good agreement with experimental results for outlet sections of process.
🔬Tür:Modelleme & Sayısal Simülasyon
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Alan Parametreleri

Özet

This paper investigated the pressure drop during the extrusion processes. The objectives of this investigation were to increase efficiency of plastic extrusion which plastic equipment produced. In the experimental processes, two rectangular dies were used. HD 7255 thermoplastic was used as the fluid material of extrusion. A difference occurred between inlet and outlet. This difference was 2.34 MPa in terms of the pressure drop and was 0.001216 (kg s -1 ) in terms of the flow rate. The results of power law model is found in good agreement with experimental results for outlet sections of process.

🔖

Bu Makaleye Atıf Yap

Dalmış, İ. S., Güler, Ü., Karakoca, A., Eruslu, S. Ö. (2015). AN EXPERIMENTAL AND THEORITICAL STUDY ON THE PRESSURE DROP OF FLUID AT EXTRUSION PROCESS. Ejovoc (Electronic Journal of Vocational Colleges), Cilt: 5 Sayı: 4, 70–77. https://doi.org/10.17339/ejovoc.96995

Kaynakça (23)

  1. Baldi, F.; Franceschini, A.; Briatico-Vangosa, F.; Locati, D. and Riccò, T. 2010. Oscillating flow in
  2. capıllary dies for a HDPE melt: effects of extrusion parameters. Int J Mater Form vol. 3 Suppl:543– 546
  3. Burghelea, T.I.; Griess, H.J. and Münstedt, H. 2010. Comparative investigations of surface
  4. instabilities (“sharkskin”) of a linear and a long-chain branched polyethylene. Journal of Non-
  5. Newtonian Fluid Mechanics, vol. 165, Issues 19–20, pp. 1093–1104
  6. Carneiro, O. S., Nobrega, J. M., Pinho, F. T., Computer aided rheological design of extrusion dies for
  7. profiles, Journal of materials processing technology, 114, pp. 75–86, 2001.
  8. Carneiro, O. S., Nobrega, J. M., Recent developments in automatic die design for profile extrusion,
  9. Plastics Rubber and Composites, 33, pp. 400-408, 2004.
  10. Dubbeldam, J.L.A. and Molenaar, J. 2003. Dynamics of the spurt instability in polymer extrusion. J.
  11. Non-Newtonian Fluid Mech. 112: 217–235
  12. D.M. and Tang, H.S. 2007. Inverse problem solution of squeeze flow for parameters of generalized
  13. Newtonian fluid and wall slip. Journal of Non-Newtonian Fluid Mechanics, 143: 133–140
  14. Ferrás, L.L. Nóbrega, J.M. and Pinho F.T. 2012. Analytical solutions for Newtonian and inelastic non-
  15. Newtonian flows with wall slip. Journal of Non-Newtonian Fluid Mechanics, 175–176: 76–88
  16. Kostic, M. M., Reifschneider, L. G., Design of Extrusion Dies, Encyclopedia of Chemical Processing,
  17. pp. 633-649, 2006.
  18. Mitsoulis, E.; Georgiou, G.C. and Kountouriotis, Z. 2012. A study of various factors affecting Kalyon,
  19. Newtonian extrudate swell. Computers & Fluids, 57: 195–207
  20. Rahimia, S.; Durbanb, D. and Khosid, S. 2010. Wall friction effects and viscosity reduction of gel
  21. propellants in conical extrusion. Journal of Non-Newtonian Fluid Mechanics, 165: 782–792
  22. Xu, X.; Ouyang, J.; Yang, B. and Liu, Z. 2013. SPH simulations of three-dimensional non-Newtonian
  23. free surface flows. Comput. Methods Appl. Mech. Engrg. 256: 101–116