KaydedilenlerDerginizi ekleyin

Dergiler / Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi / 2026 / Cilt: 17 Sayı: 2

Effect of deposition parameters on structural and mechanical properties of Novel h-BN doped TiCrNbN coatings

Yaşar Sert(KARADENİZ TEKNİK ÜNİVERSİTESİ)0000-0001-7742-0335
Tevfik Küçükömeroğlu(KARADENİZ TEKNİK ÜNİVERSİTESİ)0000-0002-4392-9966
Sayfa
488–504
Yayın Tarihi
2024-08-31
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The superiority of the contribution of working pressure on the adhesion strength was prominent compared to other parameters.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this paper, the novel h-BN doped TiCrNbN thin films was deposited on the DIN 1.2714 steel using closed field unbalanced magnetron sputtering (CFUBMS) technique with variable working pressure, bias voltage, and LaB6 target voltage.
📊
Temel Bulgular & Veri:The deposition parameters were leveled based on L9 (33) orthogonal Taguchi design method.
💡
Sonuç & Katkı:The superiority of the contribution of working pressure on the adhesion strength was prominent compared to other parameters.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:CFUBMS · Taguchi · ANOVA

Abstract

In this paper, the novel h-BN doped TiCrNbN thin films was deposited on the DIN 1.2714 steel using closed field unbalanced magnetron sputtering (CFUBMS) technique with variable working pressure, bias voltage, and LaB6 target voltage. The main goal is to determine the contribution of degrees of these parameters on structural and mechanical properties using Analysis of Variance (ANOVA). The deposition parameters were leveled based on L9 (33) orthogonal Taguchi design method. Microstructural and thickness of coatings were investigated using SEM. The coatings had granular and flawless surface properties. The thickness of the coatings was determined in the range of 874 nm and 1.69 μm. The deposition parameter that has the highest contribution to coating thickness is working pressure. Hardness and adhesion strength of coatings were determined employing nanohardness and scratch tester, respectively. The highest hardness among the coatings was 24.67 GPa, obtained with the 3x10-3 Torr working pressure, 100 V bias voltage and 600 V LaB6 target voltage parameters. The deposition parameter that has the highest contribution to hardness is working pressure. The coating conditions with the highest hardness exhibited the highest adhesion strength. The superiority of the contribution of working pressure on the adhesion strength was prominent compared to other parameters.

🔖

Bu Makaleye Atıf Yap

Sert, Y., Küçükömeroğlu, T. (2024). Effect of deposition parameters on structural and mechanical properties of Novel h-BN doped TiCrNbN coatings. Erzincan Üniversitesi Fen Bilimleri Enstitüsü Dergisi, Cilt: 17 Sayı: 2, 488–504. https://doi.org/10.18185/erzifbed.1481274

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (13)

  1. Haiko, O., Valtonen, K., Kaijalainen, A., Uusikallio, S., Hannula, J., Liimatainen, T., Kömi., (2019) Effect of Tempering on the Impact-Abrasive and Abrasive Wear Resistance of Ultra-High Strength Steels, Wear, 440-441, 203098.
  2. Cheng, W. L., Zhou, Z. F., Shum, P. W., Li, K. Y., (2013) Effect of Ni Addition on The Structure and Properties of Cr-Ni-N Coatings Deposited by Closed-Field Unbalanced Magnetron Sputtering Ion Plating, Surface and Coatings Technology, 229 84-89.
  3. Fotovvati, B., Namdari, N., Dehghanghadikolaei, A. (2019) On Coating Techniques for Surface Protection: A Review, J. Manuf. Mater. Process, 3 (1) 28-50.
  4. Sukuroglu, E. Baran, Ö. Totik Y. Efeoglu, I. (2018) Investigation of high temperature wear resistance of TiCrAlCN/TiAlN multilayer coatings over M2 steel, Journal of Adehison and Technology, 32 1428-1436.
  5. Schiller, S., Goedicke, K., Reschke, J., Kirchhoff, V., Schneider, S., Milde, F. (1993) Pulsed Magnetron Sputter Technology, Surface and Coatings Technology, 61 (1-3) 331-337.
  6. Rossnagel, S.M., Cuomo, J. J. (1989) Film Modification by Low Energy Ion Bombardment During Deposition, Thin Solid Films, 17 (1) 143-156.
  7. Yu, D., Wang, C., Cheng, X., Zhang, F. (2008) Optimization of Hybrid PVD Process of TiAlN Coatings by Taguchi Method, Applied Surface Sciences, 255 (5-1) 1865-1869.
  8. Gulten, G. Yaylali, B. Efeoglu, I. Totik, Y. Kelly, P. Kulczyk-Malecka, J. (2024) Effect of Nb and V doped elements on the mechanical and tribological properties of CrYN coatings, Surface and Coatings Technology, 477 130297.
  9. Chen, L. Holec, D. Du, Y. Mayrhofer, P.H. (2011) Influence of Zr on Structure, Mechanical and Thermal Properties of Ti-Al-N, Thin Solid Films, 59 5503-5510.
  10. Thornton, J. A. (1986) The microstructure of sputter-deposited coatings, J Vac Sci Tech A: Vac Surf Films, 4 3059-3065.
  11. Wang, X. Wang, L. S. Qi, Z. B. Yue, G. H. Chen, Y. Z. Wang, Z. C. Peng, D. L. (2010) Investigation on the structure and properties of AlxCr1−xN coatings deposited by reactive magnetron co-sputtering, Journal of Alloy and Compounds, 502 243-249.
  12. Skordaris, G. Bouzakis, K. D. Charalampous, P. Kotsanis, T. Bouzakis, E. Bejjani, R. (2018) Bias voltage effect on the mechanical properties, adhesion and milling performance of PVD films on cemented carbide inserts, Wear, 404-405 50-61.
  13. Gangopadhyay, S. Acharya, R. Chattopadhyay, A. K. Paul, S. (2010) Effect of substrate bias voltage on structural and mechanical properties of pulsed DC magnetron sputtered TiN–MoSx composite coatings, Vacuum, 84 843-850.