Dergiler / Celal Bayar Üniversitesi Fen Bilimleri Dergisi / 2026 / Cilt: 22 Sayı: 1

Numerical and Experimental Investigation of Flow, Heat Transfer, and Structural Behavior of EPDM- and PA12-Based Automotive Cooling Hoses

Doğancan Temirel(Manisa Celal Bayar University)0009-0005-4306-1641
Seda Arabacı(Manisa Celal Bayar Üniversitesi)0000-0001-8903-5952
Sayfa
189–203
Yayın Tarihi
2026-03-30
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

The findings highlight the critical role of material selection in achieving safe, durable, and efficient automotive cooling line designs.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:In this study, the flow, heat transfer, structural integrity, and dynamic behavior of EPDM- and PA12-based automotive cooling hoses were comparatively investigated using a combined numerical and experimental approach.
📊
Temel Bulgular & Veri:The results demonstrate that PA12 hoses exhibit significantly lower deformation, higher natural frequencies, and superior pressure resistance compared to EPDM hoses.
💡
Sonuç & Katkı:The findings highlight the critical role of material selection in achieving safe, durable, and efficient automotive cooling line designs.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Automotive cooling systems · EPDM · PA12

Abstract

In this study, the flow, heat transfer, structural integrity, and dynamic behavior of EPDM- and PA12-based automotive cooling hoses were comparatively investigated using a combined numerical and experimental approach. Three-dimensional CFD analyses were performed to evaluate internal velocity fields, temperature distributions, and pressure losses under identical operating conditions. Structural and modal analyses based on the finite element method were conducted to assess deformation levels, stress distributions, and natural frequencies. The numerical results were validated through experimental burst pressure tests. The results demonstrate that PA12 hoses exhibit significantly lower deformation, higher natural frequencies, and superior pressure resistance compared to EPDM hoses. Experimentally, EPDM hoses failed at approximately 16.2 bar, whereas PA12 hoses withstood pressures exceeding 59 bar, corresponding to about a +264% improvement in burst pressure capacity. For a representative geometry, the maximum deformation was reduced from approximately 8.2 mm (EPDM) to 4.83 mm (PA12) under identical loading conditions. While EPDM provides higher flexibility and vibration damping, PA12 demonstrates enhanced dimensional stability and structural robustness under high temperature and pressure conditions. The findings highlight the critical role of material selection in achieving safe, durable, and efficient automotive cooling line designs.

🔖

Bu Makaleye Atıf Yap

Temirel, D., Arabacı, S. (2026). Numerical and Experimental Investigation of Flow, Heat Transfer, and Structural Behavior of EPDM- and PA12-Based Automotive Cooling Hoses. Celal Bayar Üniversitesi Fen Bilimleri Dergisi, Cilt: 22 Sayı: 1, 189–203. https://doi.org/10.18466/cbayarfbe.1866103

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (28)

  1. . Czerwinski, F. 2021. Current trends in automotive lightweighting strategies and materials. Materials; 14(21): 6631.
  2. . Kiani, A., Khazaee, S., Badrossamay, M., Foroozmehr, E., Karevan, M. 2020. An investigation into thermal history and its correlation with mechanical properties of PA12 parts produced by selective laser sintering process. Journal of Materials Engineering and Performance; 29(2): 832–840.
  3. . Meyer, T. 2018. Injection moulding of PA12: influence of processing history on the thermal and mechanical behaviour. Doctoral dissertation, Loughborough University.
  4. . Shilav, R., Khosid, S. 2020. Development of ablative thermal response modeling of EPDM-based thermal protection systems. International Journal of Energetic Materials and Chemical Propulsion; 19(4).
  5. . Kwak, S.B., Choi, N.S. 2007. Degradation and failure mechanisms of EPDM rubbers for automotive radiator hoses. Key Engineering Materials; 353: 2864–2868.
  6. . Coran, A.Y., Patel, R. 1980. Rubber-thermoplastic compositions. Part I. EPDM-polypropylene thermoplastic vulcanizates. Rubber Chemistry and Technology; 53(1): 141–150.
  7. . Kwak, S.B., Choi, N.S. 2011. Thermo-oxidative degradation of a carbon black compounded EPDM rubber hose. International Journal of Automotive Technology; 12(3): 401–408.
  8. . Germain, Y. 1998. Burst pressure prediction of polyamide pipes. Polymer Engineering & Science; 38(4): 657–661.
  9. . Bulejko, P., Bartuli, E., Kůdelová, T., Vančura, J. 2022. Temperature-dependent burst failure of polymeric hollow fibers used in heat exchangers. Engineering Failure Analysis; 131: 105895.
  10. . Manu, I.D., Petrescu, M.G., Zisopol, D.G., Naim, R.I., Ilinca, C.N. 2024. The mechanical behavior of high-density polyethylene under short-time hydraulic pressure test. Engineering, Technology & Applied Science Research; 14(3): 14062–14068.
  11. . Xie, Z., Jia, D., Huang, X., Zhang, K., Yan, S., Chen, J., Zhong, W. 2025. Influence of temperature on hyperelastic mechanical behavior of accelerated aged EPDM rubber. Polymers; 17(12): 1626.
  12. . Foltuț, D., Vălean, E., Șoșoi, G.I., Pascal, D.T., Pospisil, J., Buzdugan, M. 2024. Comprehensive study of EPDM rubber properties: Temperature-dependent stiffness, tensile behavior and FEA calibration. IOP Conference Series: Materials Science and Engineering; 1319(1): 012025.
  13. . Xie, Z., Zhang, S., Gong, X., Zhang, K., Huang, X., Guo, W., Zhong, W. 2025. Temperature-dependent hyperelastic behavior of EPDM rubber based on digital image correlation. Materials Research Express; 12(11): 115301.
  14. . Yao, X., Wang, Z., Ma, L., Miao, Z., Su, M., Han, X., Yang, J. 2022. Temperature dependence of rubber hyper-elasticity based on different constitutive models and their prediction ability. Polymers; 14(17): 3521.
  15. . Lev, Y., Faye, A., Volokh, K.Y. 2018. Experimental study of the effect of temperature on strength and extensibility of rubberlike materials. Experimental Mechanics; 58(5): 847–858.
  16. . Bahrami, M., Lavayen-Farfan, D., Martínez, M.A., Abenojar, J. 2022. Experimental and numerical studies of polyamide 11 and 12 surfaces modified by atmospheric pressure plasma treatment. Surfaces and Interfaces; 32: 102154.
  17. . Bahrami, M., Abenojar, J., Martínez, M.A. 2021. Comparative characterization of hot-pressed polyamide 11 and 12: Mechanical, thermal and durability properties. Polymers; 13(20): 3553.
  18. . Sutanto, H., Rumende, K. 2022. Life cycle assessment of plastic components in the production of automotive filter. Polish Journal of Environmental Studies; 31(3): 2851.
  19. . Srinivasan, C., Yang, X., Schlautman, J., Wang, D., Gangaraj, S. 2020. Conjugate heat transfer CFD analysis of an oil cooled automotive electrical motor. SAE International Journal of Advances and Current Practices in Mobility; 2(2020-01-0168): 1741–1753.
  20. . Samir, D., Mohamed, W., Moustafa, A., El-Sabbagh, S. 2021. Investigation of the structure, magnetic, rheological and mechanical properties of EPDM rubber/Cu-Al-Zn alloy composites. Egyptian Journal of Chemistry; 64(12): 7377–7391.
  21. . Arshad, N., Qasim, G., Beagan, A.M. 2022. Investigations on the morphological, mechanical, ablative, physical, thermal, and electrical properties of EPDM-based composites for the exploration of enhanced thermal insulation potential. Polymers; 14(5): 863.
  22. . Sabzekar, M., Chenar, M.P., Zohuri, G., Mortazavi, S.M. 2017. Investigation of mechanical, thermal, and morphological properties of EPDM compounds containing reclaimed rubber. Rubber Chemistry and Technology; 90(4): 765–776.
  23. . Razak, N.F.D., Sani, M.S.M., Azmi, W.H., Zhang, B. 2017. Noise and vibration analysis for automotive radiator cooling fan. IOP Conference Series: Materials Science and Engineering; 257(1): 012083.
  24. . Gent, A.N. 2005. Rubber elasticity: Basic concepts and behavior. In: Science and Technology of Rubber; pp. 1–27. Academic Press.
  25. . Kumar, A., Gupta, R.K. 2018. Fundamentals of Polymer Engineering. CRC Press.
  26. . Lietze, D. 1997. Requirements on the strength of rubber hose assemblies for high pressure acetylene. Journal of Hazardous Materials; 54(3): 227–240.
  27. . Acar, M.A., Gönenli, C., Selek, M.B. 2024. Finite element analysis of the pressure vessels with various materials and thicknesses. International Journal of Scientific Research and Management; 12(09): 1452–1459.
  28. . Harper, C.A., Petrie, E.M. 2003. Plastics Materials and Processes: A Concise Encyclopedia. John Wiley & Sons.