KaydedilenlerDerginizi ekleyin

Dergiler / Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi / 2007 / Cilt: 22 Sayı: 3

Al-Si ALAŞIMLARINDA SİLİSYUM MİKTARININ DÖKÜM PARÇA-KALIP ARAYÜZEY ISI TRANSFER KATSAYISI ÜZERİNE ETKİSİ

Neşet Akar
Necati Yalçın
Sayfa
—
Yayın Tarihi
2013-02-15
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Sonuç olarak; arayüzey ısı transfer katsayısı silisyum içeriğinin azalması ile artmıştır, maksimumarayüzey ısı transfer katsayısı değerleri; %7Si’de 8900 W/m2K, %5Si’de 14600 W/m2K ve %3Si’de 19100W/m2K olarak elde edilmiştir.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Bu çalışmanın amacı katılaşma süresince su soğutmalı bakır soğutucu üzerinde tek yönlü dikey olarak katılaşanAl-Si alaşımlarında silisyum içeriğinin arayüzey ısı transferi katsayısına etkisini incelemektir.
📊
Temel Bulgular & Veri:Arayüzey ısıtransfer katsayısı silisyum içeriğine bağlı olarak, Sonlu Farklar Metoduna dayalı FORTRAN programı ilebelirlenmiştir.
💡
Sonuç & Katkı:Sonuç olarak; arayüzey ısı transfer katsayısı silisyum içeriğinin azalması ile artmıştır, maksimumarayüzey ısı transfer katsayısı değerleri; %7Si’de 8900 W/m2K, %5Si’de 14600 W/m2K ve %3Si’de 19100W/m2K olarak elde edilmiştir.
🔬Tür:Makale
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:Döküm-kalıp arayüzeyi · Al-Si alaşımları · ısı transfer katsayısı

Özet

Bu çalışmanın amacı katılaşma süresince su soğutmalı bakır soğutucu üzerinde tek yönlü dikey olarak katılaşanAl-Si alaşımlarında silisyum içeriğinin arayüzey ısı transferi katsayısına etkisini incelemektir. Arayüzey ısıtransfer katsayısı silisyum içeriğine bağlı olarak, Sonlu Farklar Metoduna dayalı FORTRAN programı ilebelirlenmiştir. Sonuç olarak; arayüzey ısı transfer katsayısı silisyum içeriğinin azalması ile artmıştır, maksimumarayüzey ısı transfer katsayısı değerleri; %7Si’de 8900 W/m2K, %5Si’de 14600 W/m2K ve %3Si’de 19100W/m2K olarak elde edilmiştir.

🔖

Bu Makaleye Atıf Yap

Akar, N., Yalçın, N. (2013). Al-Si ALAŞIMLARINDA SİLİSYUM MİKTARININ DÖKÜM PARÇA-KALIP ARAYÜZEY ISI TRANSFER KATSAYISI ÜZERİNE ETKİSİ. Gazi Üniversitesi Mühendislik Mimarlık Fakültesi Dergisi, Cilt: 22 Sayı: 3. https://ajindex.com/articles/1078868

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (227)

  1. Şahin, H.M., Kocatepe, K., Kayıkcı R. ve Akar,
  2. N., “Determination of Unidirectional Heat
  3. Transfer Coefficient during Unsteady State
  4. Solidification at Metal Chill Interface”, Energy
  5. Conversion and Management, 47, 19–34, 2006.
  6. N., “Ötektik Al-Si Alaşımında Soğutucu Yüzey
  7. Pürüzlülüğünün Arayüzey Isı Transfer
  8. Katsayısına Etkisi”, Gazi Üniversitesi
  9. Mühendislik-Mimarlık Fakültesi Dergisi, Cilt, No 3, 473-481, 2006.
  10. Kim, T.G. ve Lee, Z.H., “Time-varying Heat
  11. Transfer Coefficients Between Tube-Shaped
  12. Casting and Metal Mold”, International Journal
  13. of Heat and Mass Transfer, 40, 3513-3525,
  14. Lee, Z.H., Kim, T.G. ve Choi, Y.S., “The
  15. Movement of the Concave Casting Surface
  16. during Mushy-Type Solidification and Its Effect
  17. on the Heat-Transfer Coefficient”, Metallurgical
  18. and Materials Transactions B, 29, 1051-1056,
  19. Fortin, G, Louchez, P. ve Samuel, F H, “Factors
  20. Controlling Heat Transfer Coefficients at the
  21. Metal-Mold Interface during Solidification of
  22. Aluminum Alloys: An Analytical Study”, AFS
  23. Transactions, 100, 863-871, 1992.
  24. Hao, S.W., Zhang, Z.Q., Chen, J.Y., ve Liu, P.C.,
  25. “Heat Transfer at the Metal-Mold Interface in
  26. Ductile Iron”, AFS Transactions, 95, 601-608,
  27. Sharma, D.G.R. ve Krishnan, M., “Simulation of
  28. Heat Transfer at Casting Metal-Mold Interface“,
  29. AFS Transactions, 99, 429-438, 1991.
  30. Taha, M.A., El-Mahallawy, N.A., El-Mestekawi,
  31. M.T. ve Hassan A.A., “Estimation of Air Gap
  32. and Heat Transfer Coefficient at Different Faces
  33. of Al And Al-Si Castings Solidifying in
  34. Permanent Mould”, Materials Science And
  35. Technology, 17, 1093-1101, 2001.
  36. Santos, C.A., Quaresma, J.M.V. ve Garcia, A.,
  37. “Determination of Transient Interfacial Heat
  38. Transfer Coefficients in Chill Mold Casting”,
  39. Journal of Alloys and Compounds, 319, 174-, 2001.
  40. Santos, C.A., Siqueira, C.A., Garcia, A.,
  41. Quaresma, J.V.M. ve Spim, J.A., “Metal/Mold
  42. Heat Transfer Coefficients during Horizontal and
  43. Vertical Unsteady-State Solidification of Al-Cu
  44. and Sn-Pb Alloys”, 4th International
  45. Conference on Inverse Problems in
  46. Engineering, Rio de Janeiro, Brazil, 2002.
  47. Siqueira, C.A., Cheung, N. ve Garcia, A., “The
  48. Columnar To Equiaxed Transition During
  49. Solidification of Sn–Pb Alloys”, Journal of
  50. Alloys and Compounds, 351, 126–134, 2003.
  51. Peres, M.D., Siqueira, C.A. ve Garcia, A.,
  52. “Macrostructural and Microstructural
  53. Development in Al–Si Alloys Directionally
  54. Solidified under Unsteady-State Conditions”,
  55. Journal of Alloys and Compounds, 381,168–, 2004.
  56. Santos, C.A., Siqueira, C.A.,Garcia, A.,
  57. Quaresma, J.M.V. ve Spim, J.A., “Metal–Mold
  58. Vertical Unsteady-State Solidification of Al–Cu
  59. and Sn–Pb Alloys”, Inverse Problems in
  60. Science and Engineering, 12, 279–296,2004.
  61. Sá, F., Rocha, O.L., Siqueira, C.A. ve Garcia, A.,
  62. “The Effect of Solidification Variables on
  63. Tertiary Dendrite Arm Spacing in Unsteady-State
  64. Directional Solidification of Sn–Pb and Al–Cu
  65. Alloys”, Materials Science and Engineering A,, 131–138,2004.
  66. Spinelli, J.E., Rosa, D.M., Ferreira, I.L. ve
  67. Garcia, A., “Influence of Melt Convection on
  68. Dendritic Spacing of Downward Unsteady-State
  69. Directionally Solidified Al–Cu Alloys”,
  70. Materials Science and Engineering A, 383,
  71. 282, 2004.
  72. Souza, E. N., Cheung, N. ve Garcia, A., “The
  73. Correlation Between Thermal Variables and
  74. Secondary Dendrite Arm Spacing During
  75. Solidification of Horizontal Cylinders of Sn–Pb
  76. Alloys” Journal of Alloys and Compounds,, 110-117, 2005.
  77. Muojekwu, C.A., Samarasekera, I.V. ve
  78. Brimacombe, J.K., “Heat Transfer and
  79. Microstructure during The Early Stages of Metal
  80. Solidification”, Metallurgical and Materials
  81. Transactions B, 26, 361-382, 1995.
  82. Michel, F., Louchez, P. R. ve Samuel, F. H.,
  83. “Heat Transfer Coefficient during Solidification
  84. of Al-Si Alloys: Effects of Mold Temperature,
  85. Coating Type and Thickness”, AFS
  86. Transactions, 103, 275-283, 1995.
  87. Krishnan, M. ve Sharma, D.G.R., “Determination
  88. of Heat Transfer Coefficient between Casting and
  89. Chill in Unidirectional Heat Flow”, AFS
  90. Transactions, 102, 769-774, 1994.
  91. Krishnan, M. ve Sharma, D.G.R., “The Effect of
  92. Alloy Properties on the Heat Flow across the
  93. Casting-Mold Interface”, Scripta Metallurgica
  94. et Materialia, 28, 447-451, 1993.
  95. Narayan Prabhu, K. ve Ravishankar, B.N.,
  96. “Effect of Modification Melt Treatment on
  97. Casting/Chill Interfacial Heat Transfer and
  98. Electrical Conductivity of Al-/13% Si Alloy”,
  99. Materials Science and Engineering A, 360,
  100. 298, 2003.
  101. Suly, L.J.D., “The Thermal Interface between
  102. Casting and Chill Moulds”, AFS Transactions,, 735-744, 1976.
  103. Prabhu, K.N. ve Griffiths, W.D., “Assessment of
  104. Metal/Mould Interfacial Heat Transfer during
  105. Solidification of Cast Iron” Third International
  106. Conference on Solidification and Gravity,
  107. Miskolc, Hungary, 455-461, 1999.
  108. Lau, F., Lee, W.B., Xiong, S.M. ve Liu, B.C., “A
  109. Study of The Interfacial Heat Transfer between
  110. an Iron Casting and a Metallic Mould”, Journal
  111. of Materials Processing Technology, 79, 25–29,
  112. Broucaret, S., Michrafy, A. ve Dour, G., “Heat
  113. Transfer and Thermo-Mechanical Stresses in a
  114. Gravity Casting Die Influence of Process
  115. Parameters”, Journal of Materials Processing
  116. Thecnology, 110, 211-217, 2001.
  117. Hallam, C.P. ve Griffiths, W.D.,”A Model of the
  118. Interfacial Heat-Transfer Coefficient for the
  119. Aluminum Gravity Die-Casting Process”,
  120. Metallurgical and Materials Transactions B;, 721-733, 2004.
  121. Gozlan, E. ve Bamberger, M., “Heat Flow and
  122. Solidification in A Metal Mould” Zeitschrift für
  123. Metallkunde, 78, 677-682, 1987.
  124. Srinivasan, M.N., “Heat Transfer Coefficients at
  125. the Casting-mould Interface during Solidification
  126. of Flake Graphite Cast Iron in Metallic Moulds”,
  127. Indian Journal of Technology, 20, 123-129,
  128. Hallam, C.P., Griffiths, W.D. ve Butler, N.D.,
  129. “Interfacial Heat Transfer between A Solidifying
  130. Aluminum Alloy and A Coated Die Steel”,
  131. Materials Science Forums, 329-330, 467-472,
  132. Ho, K. ve Pehlke, R D; “Mechanisms of Heat
  133. Transfer at A Metal-Mold Interface”; AFS
  134. Transactions, 92, 587-598, 1984.
  135. Hou, T.X. ve Pehlke, R.D., “Determination of
  136. Mold-Metal Interfacial Heat Transfer and
  137. Simulation of Solidification of An Al-%13 Si
  138. Casting”, AFS Transactions, 96, 129-136, 1998.
  139. Ho, K. ve Pehlke, R.D., “Transient Methods for
  140. Determination of Metal-Mold Interfacial Heat
  141. Transfer”, AFS Transactions, 91, 689-698,
  142. Nishida, Y., Droste, W. ve Engler, S., “The Airgap
  143. Formation Process at the Casting-Mold
  144. interface and the Heat Transfer Mechanism
  145. Through the Air-gap”, Met. Transactions B, 17,
  146. 844, 1986.
  147. Liu, W., Wang G X., ve Matthys, E.F., “Thermal
  148. Analysis and Measurements for A Molten Metal
  149. Drop Impacting on A Substrate, Cooling,
  150. Solidification and Heat Transfer Coefficient”,
  151. International Journal of Heat and Mass
  152. Transfer, 38, 1387-1395,1995.
  153. Trovant, M. ve Argyropoulos, S.A., “The
  154. Implementation of A Mathematical Model To Characterize Mold Metal Interface Effects in
  155. Metal Casting”, Canadian Metallurgical
  156. Quarterly, 37, 185-196, 1998.
  157. Parker, J.K. ve Piwonka, T.S., “Gap Formation in
  158. Resin-Bonded Molds”, AFS Transactions, 108,
  159. 245, 2000.
  160. Hwang, J.C., Chuang, H.T., Jong, S.H. ve
  161. Hwang, W.S., “Measurement of Heat Transfer
  162. Coefficient at Metal-Mold Interface during
  163. Casting”, AFS Transactions, 102, 877-883,
  164. Coates, BL., Heat Transfer of the Casting
  165. Metal/Mold Interface during Solidification,
  166. PhD Thesis, Graduate Department of Materials
  167. Science and Engineering, University of Toronto,
  168. Toronto, Canada, 129-192, 2004.
  169. Hartley, J.G. ve Patterson, J.A.L., “The Influence
  170. of Temperature, Moisture Content and Binder
  171. Content on the Conductivity of Dried Bentonite-
  172. Bonded Zirkon and Silica Sands”, AFS
  173. Transactions, 91, 183-190, 1983.
  174. Kannaiah, P., Narayana, K.L. ve Roshan, H. Md.,
  175. “Thermal Properties of Molding Sands, Casting-
  176. Over Probe Embedded Specimen Method”, AFS
  177. Transactions, 95, 591-600, 1987.
  178. Hartley, J.G., Babcock, D. ve Berry, J.T., “The
  179. Thermal Conductivity of Bentonite-Bonded
  180. Molding Sands”, AFS Transactions, 89, 469-, 1981.
  181. Bandyopadhyay, B.P., Joshi, M.D. ve
  182. Chakraborty, P.N., “A Transient Method of
  183. Simultaneous Measurement of Thermal
  184. Properties of Moulding Sand Using Plane Heat
  185. Source”, British Foundryman, 77, 318-321,
  186. Seshadri, M.R. ve Ramachandran, A., “Mold
  187. Materials Thermal Properties”, AFS
  188. Transactions, 69, 616-624, 1961.
  189. of the Interfacial Heat Transfer Coefficient h in
  190. Unidirectional Heat Flow by Beck’s Non Linear
  191. Estimation Procedure”, Int. Comm. Heat Mass
  192. Transfer, 23, 203-214, 1996.
  193. Özışık, M.N., Finite Difference Methods in
  194. Heat Transfer, Mechanical and Aerospace
  195. Engineering Department, North Carolina State
  196. University, ABD, 1994.
  197. Incropera, F.P. ve Dewitt, D.P., Fundamentals of
  198. Heat and Mass Transfer, John Wiley & Sons,
  199. Purdue University, School of Mechanical
  200. Engineering, ABD, 1996.
  201. Kayıkcı, R. ve Griffiths, W.D., “The Influence of
  202. Surface Roughness on Interfacial Heat Transfer
  203. during Casting Solidification”, Foundryman, 92,
  204. 273, 1999.
  205. Kayıkcı, R., Metal-Mold Contact and Heat
  206. Transfer during Casting Solidification, PhD
  207. Thesis, Manchester Materials Science Centre,
  208. University of Manchester and UMIST,
  209. Manchester, 77-181, 1999.
  210. Wang, G.-X. ve Matthys, E.F., “Experimental
  211. Determination of the Interfacial Heat Transfer
  212. during Cooling and Solidification of Molten
  213. Metal Droplets Impacting on A Metallic
  214. Substrate: Effect of Roughness and Superheat”,
  215. Transfer, 45, 4967–4981, 2002.
  216. Gafur, M. A., Nasrul Haque, M. ve Narayan
  217. Prabhu, K., “Effect of Chill Thickness and
  218. Superheat on Casting/Chill Interfacial Heat
  219. Transfer during Solidification of Commercially
  220. Pure Aluminum”, Journal of Materials
  221. Processing Technology, 133, 257-265, 2003.
  222. Akar, N, Katılaşma Sırasında Döküm-Kalıp
  223. Ara Yüzeyinde Isı Transfer Katsayısının
  224. İncelenmesi, Doktora Tezi, Gazi Üniversitesi,
  225. Fen Bilimleri Enstitüsü, 2006., 131–138,2004.
  226. Ho, K. ve Pehlke, R D; “Mechanisms of Heat
  227. Transfer, 38, 1387-1395,1995.