Dergiler / Technological Applied Sciences / 2019 / Cilt: 14 Sayı: 2

PRODUCTION OF AA5754/B4C COMPOSITE MATERIALS BY THE SEMI-SOLID STIRRING METHOD

Sayfa
57–67
Yayın Tarihi
2019-04-20
DOI
—
🏛️Bu makalenin bibliyografik verileri ve tam metin bağlantısı DergiPark üzerinden sağlanmıştır.
DergiPark Kaydı ↗
✨

Yapay Zeka Hızlı Bakış & Çıkarımlar

AI Insight
⚡ TL;DR(1 Cümlede Hızlı Çıkarım)

Additionally, microstructure examinations were made by SEM, EDS and XRD, and the sucsesfull producibility of the B4C reinforced aluminium composites with the method that was used was seen.

📌 3 Maddede Bu Makale

🎯
Amaç & Hipotez:Aluminum composites were produced by reinforcing an AA5754 aluminum alloy with B4C particles.
📊
Temel Bulgular & Veri:The semi-solid stirring and low-pressure solidification methods were used to produce AA5754/B4C composites, and the mechanical characteristics of the samples that were obtained were determined by three-point bending and compression tests.
💡
Sonuç & Katkı:Additionally, microstructure examinations were made by SEM, EDS and XRD, and the sucsesfull producibility of the B4C reinforced aluminium composites with the method that was used was seen.
🔬Tür:Araştırma Makalesi
📍Kapsam:Genişletilmiş Akademik Örneklem
⚙️Değişkenler:B4C · Aluminum · Metal Matrix Composite

Özet

Aluminum composites were produced by reinforcing an AA5754 aluminum alloy with B4C particles. The semi-solid stirring and low-pressure solidification methods were used to produce AA5754/B4C composites, and the mechanical characteristics of the samples that were obtained were determined by three-point bending and compression tests. Additionally, microstructure examinations were made by SEM, EDS and XRD, and the sucsesfull producibility of the B4C reinforced aluminium composites with the method that was used was seen.

Abstract

Aluminum composites were produced by reinforcing an AA5754 aluminum alloy with B4C particles. The semi-solid stirring and low-pressure solidification methods were used to produce AA5754/B4C composites, and the mechanical characteristics of the samples that were obtained were determined by three-point bending and compression tests. Additionally, microstructure examinations were made by SEM, EDS and XRD, and the sucsesfull producibility of the B4C reinforced aluminium composites with the method that was used was seen.

🔖

Bu Makaleye Atıf Yap

YAKUT, R., TAŞKIN, N. Ü. (2019). PRODUCTION OF AA5754/B4C COMPOSITE MATERIALS BY THE SEMI-SOLID STIRRING METHOD. Technological Applied Sciences, Cilt: 14 Sayı: 2, 57–67. https://ajindex.com/articles/1007663

📄 Tam Metin PDF Okuyucu

📄

PDF görüntüleyici hazırlanıyor...

Kaynakça (12)

  1. Toptan, F., (2011). Production of High Wear Resistant B4c Particle Reınforced Aluminum Matrix Composites. PhD Thesis. İstanbul: Yıldız Technical University Institute of Science and Technology
  2. Pul, M., Calin, R., and Citak, R., (2011). An Investigation of Surface Quality of Turning in Al Matrix MgO Reinforced Composite Materials. Journal of the Faculty of Engineering and Architecture of Gazi University: Vol::26, No:1, pp:81-88,
  3. Aksöz, S., Özdemir, A. T., Bostan, B., (2012). Alloyed AA2014 Aluminum Powders Synthesized with Carbon and Determined Properties. Journal of the Faculty of Engineering and Architecture of Gazi University, Vol: 27, No: 1, pp: 109-115
  4. Arslan, D., Gürü, M., (2013. Production of Boron Carbıde by Mechanochemical Method and Investigation of Usability on the Aluminum Based Composite Material. Journal of the Faculty of Engineering and Architecture of Gazi University, Vol: 28, No: 4, pp: 875-883
  5. Tosun, N., Kuru, C., and Altıntaş, E., (2010). Investigation of Surface Roughness in Milling with Air and Conventional Cooling Method. Journal of the Faculty of Engineering and Architecture of Gazi University, Vol: 25, No: 1, pp: 141-146
  6. Tuncer, N., Taşdelen, B., and Arslan, G., (2011). Effect of Passivation and Precipitation Hardening on Processing and Mechanical Properties of B4C/Al Composites, Ceramics International, Vol: 37, No: 7, pp: 2861-2867
  7. Ekici, E., (2012). The Manufacture of Aluminium Matrix Composites with B4C Reinforcing Element and Addition of Graphite and the Analysis of Mechanical Features and Their Machinability on Milling. PhD Thesis. Ankara: Gazi University Institute of Science and Technology
  8. Groover, M.P., (2010). Fundamentals of Modern Manufacturing, Materials, Processes and Systems 4th Edition. U.S.A
  9. Yalçın, E.D., (2010). Investigation of Joinability AA 7075 and AA5754 Aluminum Alloys by Friction Stir Welding Method. Master Thesis. Karadeniz Technical University Institute of Science and Technology
  10. Singla, M., Dwivedi, D. D., Singh, L., and Chawla, V., (2009). Development of Aluminium Based Silicon Carbide Particulate Metal Matrix Composite. Journal of Minerals & Materials Characterization & Engineering, Vol:8, No:6, pp:455-467
  11. Atik, E., Ünlü, B.S., Sen, O., and Çavdar, U., (2006). Investigation of Wear Strength and Mechanical Properies of Particle Reinforced AlSi12CuNiMg Composites. C.B.U. Journal of Science, Vol:2 No:2 pp:75-87
  12. Kılıç, C., (2008). Sıkıştırma Döküm Yön