| Design and Construction of Ankle Foot Orthosis By Means Of Three Dimensional Printers | Levent Aydın, Serdar Küçük | 1–8 |
| On the Yielding of Two-Layer Composite Spherical Pressure Vessels | Tolga Akış | 9–16 |
| Acoustic Emission Analysis Method of Reinforced Concrete Column with the Jacketing Methods | Anıl Özdemir, Emre Ercan | 17–23 |
| A Parametric Study on the Heterogeneous Photo-Fenton-Like Oxidation of Bisphenol-A over an Fe/TiO2 Catalyst under Visible Light | Meral Dükkancı | 25–36 |
| Dynamic Weight Estimation Application with Artificial Neural Networks | Mehmet Yumurtacı, İsmail Yabanova | 37–41 |
| Evaluation of Machinability of AISI 304 and AISI 316 Austenitic Stainless Steels | Nuırsen Altan Özbek, Adem Çiçek, Mahmut Gülesin, Onur Özbek | 43–49 |
| Investigation of Melt Flow Index Properties of Polypropylene Reinforced Aluminum Powder | Abdülmecit Güdaş, Servet Temel, Mehmet Altuğ | 51–59 |
| A Web-Based Educational Tool For Simulation of Reactive Power Compensation With Synchronous Motor | Ramazan Bayındır, Seyfettin Vadi | 61–69 |
| Model Based Predictive Engine Torque Control for Improved Driveability | Murat Ötkür, Orhan Atabay, İsmail Murat Ereke | 71–82 |
| Modelling and Comparative Analysis of Different Type of Batteries Used for Renewable Energy Support | Yağmur Kırçiçek, Ahmet Aktaş, Şule Özdemir | 83–90 |
| Physical and Mechanical Properties of Polypropylene Fiber Reinforced Mortars | İlker Bekir Topçu, Onur Enes Demirel, Tayfun Uygunoğlu | 91–96 |
| Determination of Protection and Relay Coordination Strategy in Electrical Power Systems Based on Renewable Energy Generation Resource Using Petri Net Method | Nihat Pamuk | 97–110 |
| Monitoring and Estimating of Vibration and Cutting Force Based Tool Wear via Fuzzy Logic | Aydin Salımıasl, Mohammad Rafıghı | 111–120 |
| Effect of Fabrication Parameters on Hardness of Al-Cu Functionally Graded Materials Manufactured by Centrifugal Casting | Semih Ağca, Neşet Akar | 121–127 |
| Modeling Of Liquid-Liquid Equilibrium Data and Estimation of New Binary Interaction Parameters for NRTL Model for the Quaternary System Water/ Ethanol/1- Butanol / KCL at 298.15K | Bourayou Euchi N., Meniai A-h., Gouaoura A. | 129–135 |
| Investigation of Safety Culture Level Among Turkish Construction Sector Employees and its Relation with Safety Performance | Serkan Yıldız, Mustafa Yılmaz | 137–149 |
| Trajectory Planning of a 5-DOF Serial Robot Manipulator in Joint-Space | Sabri Uzuner, Nihat Akkuş, Metin Toz | 151–157 |
| Dynamic Behavior Analysis of Rotor Supported by Damped Rolling Element Bearing Housing | Hamit Saruhan, Menderes Kam, Fuat Kara | 159–164 |
| Determination of Contact Parameters of Au/n-Ge Schottky Barrier Diode with Rubrene Interlayer | Murat Yıldırım | 165–173 |
| Permisson Comparison Based Malware Detection System for Android Mobile Applications | Recep Sinan Arslan, İbrahim Alper Doğru, Necaattin Barışçı | 175–189 |
| Influence of Coolant on the Performance of Electro Discharge Hole Drilling | Kürşad Göv | 191–196 |
| Loss Calculation Technique With Randomize Load Curves | Ahmet Önen | 197–203 |
| Comparison of A Distance Controller Design Via Constant Distance And Constant Time Gap (CTG) Methods In An Adaptive Cruise Control (ACC) System | Hasan Şahin | 205–210 |
| Comparison of Energy and Exergy Analysis for Variable Refrigerant Flow System (VRF) with Different Rerigerants | Ali İbrahim Atılgan, Utku Türkmen | 211–222 |
| Investigation of Corrosion Behavior of Powder Metallurgy Materials Produced From DistaloyAB Powders and Electrochemically Coated Chromium With Diamond Nanopartical Additive | E. Zeynep Bilgili, Elmas Salamcı, Abdurrahman Asan | 223–230 |
| The Effect of Heat Treatment on The Surface Roughness and Varnish Adhesion of Wood | Suat Altun, Musa Esmer | 231–239 |
| Examination of Flow Effects in Francis Turbine Models with Different Numbers of Rotor Blades | Selçuk Keçel, H. Güçlü Yavuzcan, Adnan Sözen | 241–249 |