Journals / Türkiye Ormancılık Dergisi / 2023 / Cilt: 24 Sayı: 2

Utilization of beech wood flours obtained after thinning and beech cupula in wood plastic composite (WPC) production

Aralama çalışması sonrasında elde edilen kayın odunlarının ve kupulasının odun plastik kompozit (OPK) üretiminde değerlendirilmesi

Pages
139–149
Publication Date
2023-06-28
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It is thought that better performance will be achieved when beech wood flours are used alone or their cupulas are used together with beech wood flours and less than 25%.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study aims to determine the effects of the evaluation of beech woods obtained from thinning, which are in the firewood class, and also beech cupulas as a filler in the manufacturing of wood plastic composite (WPC) on the technological properties of the composites.
📊
Key Findings & Data:For this purpose, polypropylene (PP) based WPC production was carried out with the usage of 2 different fillers rate (0 or 50%) and three different types of lignocellulosic fillers (50% beech, 25% beech + 25% cupula or 50% cupula).
💡
Conclusion & Impact:It is thought that better performance will be achieved when beech wood flours are used alone or their cupulas are used together with beech wood flours and less than 25%.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:OPK · MAPP · Fagus orientalis

Abstract

This study aims to determine the effects of the evaluation of beech woods obtained from thinning, which are in the firewood class, and also beech cupulas as a filler in the manufacturing of wood plastic composite (WPC) on the technological properties of the composites. For this purpose, polypropylene (PP) based WPC production was carried out with the usage of 2 different fillers rate (0 or 50%) and three different types of lignocellulosic fillers (50% beech, 25% beech + 25% cupula or 50% cupula). In addition, maleic anhydride grafted polypropylene (MAPP) in 2 different ratios (0% and 3%) was used as a compatibilizing agent and the effects of MAPP usage were investigated. The mechanical (tensile strength, elongation at break, flexural strength, modulus of elasticity and impact strength) and physical (density and hardness) properties of the produced WPCs were determined in accordance with the relevant standards. As a result, when the lignocellulosic fillers were compared within themselves, it was seen that the highest mechanical properties were obtained with the usage of beech wood flour. The mechanical strength properties were negatively affected by the addition of cupula flours into the composite materials, and the mechanical properties were negatively affected by the increase in the cupula rates. Generally, the usage of MAPP has improved the mechanical properties of the WPCs. In Composite groups produced by using only beech wood flour together with MAPP, the highest values were obtained in all mechanical properties except elongation at break, and significant increases were observed compared to the control group. As a result of the study, PP-based WPC productions, in which beech wood flours and cupula flours are used as fillers, have been successfully carried out. It is thought that better performance will be achieved when beech wood flours are used alone or their cupulas are used together with beech wood flours and less than 25%.

Özet

Bu çalışma kapsamında aralama çalışması sonucunda yakacak odun sınıfında bulunan kayın odunlarının ve kayın kupulalarının odun plastik kompozit (OPK) üretiminde dolgu maddesi olarak değerlendirilmesinin üretilecek olan kompozitlerin teknolojik özellikleri üzerine etkilerinin belirlenmesi amaçlanmıştır. Bu amaç doğrultusunda 2 farklı dolgu maddesi kullanım oranı (%0 veya %50) ve 3 farklı tipte lignoselülozik dolgu maddesi kullanımı (%50kayın, %25kayın+%25kupula veya %50 kupula) ile polipropilen (PP) bazlı OPK üretimleri gerçekleştirilmiştir. Bunun yanı sıra 2 farklı oranda (%0 ve %3) maleik anhidrit aşılanmış polipropilen (MAPP) uyumlaştırıcı ajan olarak kullanılmış ve MAPP kullanımının etkileri incelenmiştir. Üretilen OPKların mekanik (çekme direnci, kopmada uzama, eğilme direnci, eğilmede elastikiyet modülü ve darbe direnci) ve fiziksel (yoğunluk ve sertlik) özellikleri ilgili standartlara uygun olarak belirlenmiştir. Elde edilen sonuçlar neticesinde lignoselülozik dolgu maddelerini kendi içerisinde karşılaştırıldığında kayın odun unlarının kullanımı ile en yüksek mekanik özelliklerin elde edildiği, kupula unlarının kompozit malzemelerin içerisine eklenmesi ile mekanik direnç özelliklerin negatif etkilendiği ve kupula kullanım oranının artması ile mekanik özelliklerinde negatif yönde etkilenmesinin arttığı görülmüştür. Genel olarak MAPP kullanımı üretilen OPKların mekanik özelliklerini iyileştirmiştir. Sadece kayın odun unlarının MAPP ile birlikte kullanılması ile üretilen Kompozit gruplarında kopmada uzama özelliği hariç tüm mekanik özelliklerde en yüksek değerler elde edilmiş ve kontrol grubuna nazaran belirgin artışlar gözlemlenmiştir. Çalışma neticesinde kayın odun unları ve kupula unlarının dolgu maddesi olarak kullanıldığı PP-bazlı OPK üretimleri başarılı bir şekilde gerçekleştirilmiştir. Kayın odun unların tek başına, kupulalarının ise kayın odun unları ile birlikte ve %25 oranından daha az kullanılması ile daha iyi performans yakalanacağı düşünülmektedir.

🔖

Cite This Article

ŞAHİN, M., BAŞBOĞA, İ. H. (2023). Utilization of beech wood flours obtained after thinning and beech cupula in wood plastic composite (WPC) production. Türkiye Ormancılık Dergisi, Cilt: 24 Sayı: 2, 139–149. https://ajindex.com/articles/964536

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (5)

  1. Acar, H., 2014. MDF tozu ve pirinç sapı atıklarının termoplastik kompozitlerin üretiminde değerlendirilmesi. Yüksek Lisans Tezi, Kahramanmaraş Sütçü İmam Üniversitesi,
  2. Fen Bilimleri Enstitüsü, Kahramanmaraş. Adusumalli, R.B., Weber, H.K., Roeder, T., Sixta, H. and Gindl, W., 2010. Evaluation of experimental parameters in the microbond test with regard to lyocell fibers. J Reinf Plast Compos, 29:2356–2367. https://doi.org/10.1177/0731684409349929 ASTM D1238-10. 2013. Standard test method for melt flow rates of thermoplastics by extrusion plastometer. West Conshohocken, PA, USA. ASTM D1505-18. 2018. Standard test method for density of plastics by the density-gradient technique. West Conshohocken, PA, USA. ASTM D2240. 2017. Standard test method for rubber property-durometer hardness. West Conshohocken, PA, USA. ASTM D256. 2010. Standard test for determining the izod pendulum impact resistance of plastics. West Conshohocken, PA, USA. ASTM D3417-99. 2004. Standard test method for enthalpies of fusion and crystallization of polymers by differential scanning calorimetry (DSC). West Conshohocken, PA, USA. ASTM D638. 2010. Standard test for tensile properties of plastics. West Conshohocken, PA, USA. ASTM D648-18. 2018. Standard test method for deflection temperature of plastics under flexural load in the edgewise position. West Conshohocken, PA, USA. ASTM D6662. 2001. Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards. West Conshohocken, PA, USA. ASTM D785-08. 2015. Standard test method for rockwell hardness of plastics and electrical insulating materials. West Conshohocken, PA, USA. ASTM D790. 2010. Standard test methods for flexural properties of unreinforced and reinforced plastics and electrical insulating materials. West Conshohocken, PA, USA. ASTM D792. 2008. Standard test methods for density and specific gravity (relative density) of plastics by displacement. West Conshohocken, PA, USA. Avcı, E., 2012. Ahşap plastik kompozitlerin kullanım performansları üzerine araştırmalar. Doktora tezi, İstanbul Üniversitesi,
  3. Fen Bilimleri Enstitüsü, İstanbul.
  4. Balatinecz, J.J., Woodhams, R.T., 1993. Wood-plastic composites, doing more with less. Journal of Forestry, 91(11): 22-26.
  5. Başboğa, İ.H., Atar, İ., Karakuş, K., Mengeloğlu, F., 2020. Determination of some technological properties of injection molded pulverized‑hdpe based composites reinforced with micronized waste tire powder and red pine wood wastes. Journal of Polymers and the Environment, 28