SavedAdd your journal

Journals / Adıyaman Üniversitesi Mühendislik Bilimleri Dergisi / 2023 / Cilt: 10 Sayı: 20

FABRICATION AND PROPERTIES OF FeCrC REINFORCED COPPER ALLOYS BY MECHANICAL ALLOYING

MEKANİK ALAŞIMLAMA İLE FeCrC TAKVİYELİ BAKIR ALAŞIMLARININ ÜRETİMİ VE ÖZELLİKLERİ

Tanju TEKER
Serdar Osman YILMAZ
Pages
135–140
Publication Date
2023-08-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The hardness of Cu increased significantly after grinding with FeCrC.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, properties and fabrication of FeCrC reinforced copper alloys by mechanical alloying were examined using mechanical grinding, optical microscopy, energy dispersive spectroscope, X-ray diffraction, and hardness testing.
📊
Key Findings & Data:High performance Cu was further strengthened by a combination of fine grain and alloying.
💡
Conclusion & Impact:The hardness of Cu increased significantly after grinding with FeCrC.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Mechanical alloying · Cu matrix alloy · morphology

Abstract

In this study, properties and fabrication of FeCrC reinforced copper alloys by mechanical alloying were examined using mechanical grinding, optical microscopy, energy dispersive spectroscope, X-ray diffraction, and hardness testing. MA had a very good ability to mix Cu-FeCrC particles. High FeCrC provided more cold work during milling. Thus, smaller crystallite size and greater internal stress occurred in Cu alloys. High performance Cu was further strengthened by a combination of fine grain and alloying. C23C6, Cr7C3 and α–Cu detected in the structure. The hardness of Cu increased significantly after grinding with FeCrC.

Özet

In this study, properties and fabrication of FeCrC reinforced copper alloys by mechanical alloying were examined using mechanical grinding, optical microscopy, energy dispersive spectroscope, X-ray diffraction, and hardness testing. MA had a very good ability to mix Cu-FeCrC particles. High FeCrC provided more cold work during milling. Thus, smaller crystallite size and greater internal stress occurred in Cu alloys. High performance Cu was further strengthened by a combination of fine grain and alloying. C23C6, Cr7C3 and α–Cu detected in the structure. The hardness of Cu increased significantly after grinding with FeCrC.

🔖

Cite This Article

TEKER, T., YILMAZ, S. O. (2023). FABRICATION AND PROPERTIES OF FeCrC REINFORCED COPPER ALLOYS BY MECHANICAL ALLOYING. Adıyaman Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 10 Sayı: 20, 135–140. https://ajindex.com/articles/961112

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Zhang DL. Processing of advanced materials using high-energy mechanical milling. Progress in Materials Science 2004; 49: 537–560.
  2. Lahiri I, Bhargava S. Compaction and sintering response of mechanically alloyed Cu–Cr powder. Powder Technology 2009; 189: 433–438.
  3. Liu Q, Zhang X, Ge Y, Wang J, Cui JZ. Effect of processing and heat treatment on behavior of Cu-Cr-Zr alloys to railway contact wire. Metallurgical and Materials Transaction A 2006; 37: 3233–3238.
  4. Batra IS, Dey GK, Kulkarni UD, Banerjee S. Microstructure and properties of a C-Cr-Zr alloy. Journal of Nuclear Materials 2001; 299: 91–100.
  5. Zhou HT, Zhong JW, Zhou X, Zhao ZK, Li OB. Microstructure and properties of Cu-1.0Cr0.2Zr-0.03Fe alloy. Materials Science and Engineering A 2008; 498: 225–230.
  6. Fang Q, Kang Z, Gan Y, Long Y. Microstructures and mechanical properties of spark plasma sintered Cu-Cr composites prepared by mechanical milling and alloying. Materials and Design 2015; 88: 8–15.
  7. Shkodich NF, Rogachev AS, Vadchenko SG, Moskovskikh DO, Sachkova NV, Rouvimov S, Mukasyan AS. Bulk Cu-Cr nanocomposites by high-energy ball milling and spark plasma sintering. Journal of Alloys and Compounds 2014; 617: 39–46.
  8. Fang Q, Kang ZX. An investigation on morphology and structure of Cu-Cr alloy powders prepared by mechanical milling and alloying. Powder Technology 2015; 270: 104–111.
  9. Hu LX, Wang ED. Fabrication of high strength conductivity submicron crystalline Cu-5% Cr alloy by mechanical alloying. Transactions Nonferrous Metals Society of China 2000; 10: 209–212.
  10. Zhou J, Zhu D, Tang L, Jiang X, Chen S, Peng X, Hu C. Microstructure and properties of powder metallurgy Cu-1%Cr-0.65%Zr alloy prepared by hot pressing. Vacuum 2016; 131: 156–163.
  11. Wang Y, Tang BH, Li FY. The properties of self-formed diffusion barrier layer in Cu(Cr) alloy. Vacuum 2016; 126: 51–54.
  12. Zhang C, Wang Y, Yang Z, Guo Y, Ding BJ. Microstructure and properties of vacuum induction melted CuCr25 alloys. Journal of Alloys and Compounds 2004; 366: 289–292.
  13. Shen DP, Zhu YJ, Yang X, Tong WP. Investigation on the microstructure and properties of Cu-Cr alloy prepared by in-situ synthesis method. Vacuum 2018; 149: 207–213.
  14. Sauvage X, Jessner P,Vurpillot F, Pippan R. Nanostructure and properties of a Cu–Cr composite processed by severe plastic deformation. Scripta Materialia 58; 12: 1125–1128.
  15. Zhou ZM, Wang YP, Gao J, Kolbe M. Microstructure of rapidly solidified Cu 25wt.% Cr alloys. Materials Science and Engineering A 2005; 398: 318–322.
  16. Seo D, Ogawa