Journals / Scientific Mining Journal / 2022 / Cilt: 61 Sayı: 3

Use of marble dust containing filler mixture in composite slab production: Relationship between roasting conditions and physical properties of the slab

Mermer tozunun kompozit plaka üretiminde kullanımı: Mermer tozu içeren dolgu karışımının kavurma koşulları ile plaka fiziksel özellikleri arasındaki ilişki

Pages
135–141
Publication Date
2022-09-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Larnite and quartz were determined to be effective on improved physical properties than wollastonite and calcio olivine.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Marble dust generated during slab cutting as reject causes significant environmental problems due to increased reactive surface area.
📊
Key Findings & Data:Physical properties were determined to retrogress as the roasting temperature increased to 1100°C possibly due to rate of free lime in roasted filler, and then improved again reaching peak point at 1200°C.
💡
Conclusion & Impact:Larnite and quartz were determined to be effective on improved physical properties than wollastonite and calcio olivine.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Kompozit plaka · Mikronize kuvars · Mermer tozu

Abstract

Marble dust generated during slab cutting as reject causes significant environmental problems due to increased reactive surface area. It has closer size distribution with micronized quartz filler used in composite slab. Owing to its high hardness, micronized quartz production is an energy intensive process. This study was conducted to investigate the applicability of marble dust in composite slab production together with micronized quartz as filler. The filler mixture was roasted to mitigate drawback arising from low hardness of marble dust. XRD characterization revealed that phases in roasted filler were wollastonite, larnite, calcio olivine, quicklime and free quartz depending on the roasting temperature and time. Physical tests were applied to clarify the effect of sinter phases on slab properties. Physical properties were determined to retrogress as the roasting temperature increased to 1100°C possibly due to rate of free lime in roasted filler, and then improved again reaching peak point at 1200°C. They ameliorated by increasing roasting time at 1200°C. Larnite and quartz were determined to be effective on improved physical properties than wollastonite and calcio olivine.

Özet

Plaka kesim sürecinde artık olarak açığa çıkan mermer tozu, artan reaktif yüzey alanından dolayı önemli çevresel sorunlara neden olmaktadır. Mermer tozu, kompozit plakada dolgu olarak kullanılan mikronize kuvars ile yakın boyut dağılımına sahiptir. Yüksek sertliği nedeniyle mikronize kuvars üretimi enerji yoğun bir işlemdir. Bu çalışma, mermer tozunun kompozit plaka üretiminde mikronize kuvars ile birlikte dolgu malzemesi olarak uygulanabilirliğini araştırmak amacıyla yapılmıştır. Mermer tozunun düşük sertliğinden kaynaklanan dezavantajı azaltmak için dolgu karışımlarına kavurma işlemi uygulanmıştır. XRD ile yapılan karakterizasyon; kavurma sıcaklığına ve süresine bağlı olarak kavrulmuş dolgudaki fazların, serbest kuvars, volastonit, larnit, kalsiyo olivin ve sönmemiş kireç olduğunu ortaya koymuştur. Sinter fazlarının plaka özelliklerine etkisini aydınlatmak için fiziksel testler uygulanmıştır. Kavurma sıcaklığı 1100°C'ye çıkarıldığında, muhtemelen kavrulmuş dolguda bulunan serbest kireç oranına bağlı olarak fiziksel özellikler kötüleşmiş, 1200°C'ye çıkarıldığında ise tekrar iyileşerek en yüksek değere ulaşmıştır. 1200°C'de kavurma süresi artırılınca fiziksel özellikler iyileşmiştir. Larnit ve kuvarsın, iyileştirilmiş fiziksel özellikler üzerinde, volastonit ve kalsiyo olivine göre daha etkili olduğu belirlenmiştir.

🔖

Cite This Article

BAŞ, S., GÜLER, T., AKTÜRK, S. (2022). Use of marble dust containing filler mixture in composite slab production: Relationship between roasting conditions and physical properties of the slab. Scientific Mining Journal, Cilt: 61 Sayı: 3, 135–141. https://ajindex.com/articles/953740

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (7)

  1. Abenojar, J., Velasco, F., Bautista, A., Campos, M, Bas, J.A., Torralba, J.M. 2003. Atmosphere influence in sintering process of stainless steels matrix composites reinforced with hard particles. Composite Science and Technology. 63(1), 69-79. DOI: 10.1016/S0266-3538(02)00179-3
  2. Akaogi, M., Yano, M., Tejima, Y., Uijima, M., Kojitani, H. 2004. High-pressure transitions of diopside and wollastonite: Phase equilibria and thermochemistry of CaMgSi2O6, CaSiO3 and CaSi2O5–CaTiSiO5 system. Physics of the Earth and Planetary Interiors. 143-144, 145-156. DOI: 10.1016/j.pepi.2003.08.008 Albalak, R. 2012. Engineered Stone and Methods of Manufacturing Same. U.S. Patent No. 2012/0196087 A1. Arıcı, E., Ölmez, D., Özkan, M., Topçu, N., Çapraz, F., Deniz, G., Altınyay, A. 2019. The improvement of mechanical strength and surface properties on quartz surfaces. Afyon Kocatepe University Journal of Science and Engineering. 19, 326-332. de Bakker, J. 2014. Energy use of fine grinding in mineral processing. Metallurgical and Materials Transactions E. 1, 8–19. DOI: 10.1007/s40553-013-0001-6
  3. Booncharoen, W., Jaroenworaluck, A., Stevens, R. 2011. A synthesis route to nanoparticle dicalcium silicate for biomaterials research. Journal of Biomedical Materials Research Part B. 99B, 230–238.
  4. Borsellino, C., Calabrese, L., Bella, G.D. 2009. Effects of powder concentration and type of resin on the performance of marble composite structures. Construction and Building Materials. 23(5), 1915-1921. DOI: 10.1016/j.conbuildmat.2008.09.005 Callister, W.D., Rethwisch, D.G. 2018. Materials Science and Engineering: An Introduction. Wiley. ISBN: 978-1-119-40549-8
  5. Cardenas, A., Pineda, Y., Santos, A.S., Vera, E. 2016. Effect of glow discharge sintering in the properties of a composite material fabricated by powder metallurgy. Journal of Physics: Conference Series. 687, 1-4. DOI:10.1088/1742-6596/687/1/012025
  6. Erdem, R.T., Öztürk, A.U. 2012. Effect of marble powder additive on freezing-thawing properties of cement mortar. BEU Journal of Science. 1(2), 85-91.
  7. Gazi, A., Skevis, G., Founti, M.A. 2012. Energy efficiency and environmental assessment of a typical marble quarry and processing plant. Journal of Cleaner Production. 32, 10-21. DOI: 10.1016/j.jclepro.2012.03.007 Gobechiya, E.R., Yamnova, N.A., Zadov, A.E., Gazeev, V.M. 2008. Calcio-olivine γ-Ca2SiO4: I. Rietveld refinement of the crystal structure. Crystallography Report. 53(3), 404-408. DOI: 10.1134/S1063774508030073 Göktaş, M., Erdemoğlu, M. 20