Journals / Sakarya University Journal of Science / 2019 / Cilt: 23 Sayı: 6

Damage resistance investigation of Armox 500T and Aluminum 7075-T6 plates subjected to drop-weight and ballistic impact loads

Pages
1080–1095
Publication Date
2019-12-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

M4, M7, M9, and M10 models were found to be more resistant to the ballistic impact loads than other models.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The main objective of this paper is to investigate damage resistance of Armox 500T and Aluminum 7075-T6 plates subjected to drop-weight and ballistic impact loads.
📊
Key Findings & Data:In this study, firstly drop weight and ballistic impact resistance of the Armox-500T and Al7075-T6 materials was examined.
💡
Conclusion & Impact:M4, M7, M9, and M10 models were found to be more resistant to the ballistic impact loads than other models.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Damage resistance · Drop-weight · Ballistic impact

Abstract

The main objective of this paper is to investigate damage resistance of Armox 500T and Aluminum 7075-T6 plates subjected to drop-weight and ballistic impact loads. Investigating the behavior of structures under the low or the high velocity impact loads is an important research topic. The study of materials and their combinations provides fundamental understanding of many engineering structures. In this study, firstly drop weight and ballistic impact resistance of the Armox-500T and Al7075-T6 materials was examined. Ballistic impact analyses were carried out using 7.62 API projectiles with an initial velocity of 800 m/s. During the drop-weight analyses, the drop of 5.5 kg weight from the 800 mm distance was modeled. The situations at which target plates of different thickness can be fully penetrated or not to be fully penetrated by the projectile, the final (residual) velocities in the fully penetrated plates and the amount of energy absorbed by the target plates were investigated. 6.72 API projectiles with an initial velocity of 800 m/s could not fully penetrated the 10 mm Armox-500T target and 26 mm Al7075-T6 target. When drop-weight results are concerned, the maximum impact loads of the Armox-500T target is higher than the Al7075-T6, and the deformation amount is less. In addition, 10 different hybrid models, which consist of various combination of Armox 500T and Al7075-T6 materials in different thicknesses and orientations, have been defined. These models were compared with each other and models that are more resistant to ballistic impact loads were determined. M4, M7, M9, and M10 models were found to be more resistant to the ballistic impact loads than other models.

🔖

Cite This Article

YETER, E. (2019). Damage resistance investigation of Armox 500T and Aluminum 7075-T6 plates subjected to drop-weight and ballistic impact loads. Sakarya University Journal of Science, Cilt: 23 Sayı: 6, 1080–1095. https://ajindex.com/articles/941969

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (8)

  1. [R. Villavicencio and C. G. Soares, "Impact response of rectangular and square stiffened plates supported on two opposite edges," Thin-Walled Structures, vol. 68, pp. 164-182, 2013. B. Liu and C. G. Soares, "Plastic response and failure of rectangular cross-section tubes subjected to transverse quasi-static and low-velocity impact loads," International Journal of Mechanical Sciences, vol. 90, pp. 213-227, 2015. M. De Moura and A. Marques, "Prediction of low velocity impact damage in carbon–epoxy laminates," Composites Part A: Applied Science and Manufacturing, vol. 33, no. 3, pp. 361-368, 2002.
  2. T. Boonkong, Y. Shen, Z. Guan, and W. Cantwell, "The low velocity impact response of curvilinear-core sandwich structures," International Journal of Impact Engineering, vol. 93, pp. 28-38, 2016. Y. Liu and B. Liaw, "Drop-weight impact tests and finite element modeling of cast acrylic/aluminum plates," Polymer Testing, vol. 28, no. 8, pp. 808-823, 2009.
  3. Y. Shi, T. Swait, and C. Soutis, "Modelling damage evolution in composite laminates subjected to low velocity impact," Composite Structures, vol. 94, no. 9, pp. 2902-2913, 2012.
  4. E. Sevkat, B. Liaw, F. Delale, and B. B. Raju, "Drop-weight impact of plain-woven hybrid glass–graphite/toughened epoxy composites," Composites Part A: Applied Science and Manufacturing, vol. 40, no. 8, pp. 1090-1110, 2009.
  5. C. Menna, D. Asprone, G. Caprino, V. Lopresto, and A. Prota, "Numerical simulation of impact tests on GFRP composite laminates," International Journal of Impact Engineering, vol. 38, no. 8-9, pp. 677-685, 2011.
  6. R. Santiago, W. Cantwell, and M. Alves, "Impact on thermoplastic fibre-metal laminates: experimental observations," Composite structures, vol. 159, pp. 800-817, 2017.
  7. E. M. Soliman, M. P. Sheyka, and M. R. Taha, "Low-velocity impact of thin woven carbon fabric composites incorporating multi-walled carbon nanotubes," International Journal of Impact Engineering, vol. 47, pp. 39-47, 2012. D. Feng and F. Aymerich, "Damage prediction in composite sandwich panels subjected to low-velocity impact," Composites Part A: Applied Science and Manufacturing, vol. 52, pp. 12-22, 2013.
  8. P. Rawat, K. Singh, and N. K. Singh, "Numerical investigation of damage area due to different shape of impactors at low velocity impact of GFRP laminate," Materials Today: Proceedings, vol. 4, no. 8, pp. 8731-8738, 2017. F. Sarasini et al., "Effect of basalt fiber hybridization on the impact behavior under low impact velocity of glass/basalt woven fab