Journals / Current Research in Dental Sciences / 2020 / Cilt: 30 Sayı: 1

FARKLI NANOPARTİKÜLLERLE GÜÇLENDİRİLEN MİKRODALGA ENERJİSİ İLE POLİMERİZE OLAN AKRİLİK REZİNİN MEKANİK VE FİZİKSEL ÖZELLİKLERİNİN DEĞERLENDİRİLMESİ

Pages
101–106
Publication Date
2020-01-15
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Keywords: Polymethylmethacrylate, Nanoparticle, Surface roughness, Surface hardness.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Amaç: PMMA, protetik diş hekimliğinde protez kaide materyali olarak yaygın kullanılmasına rağmen düşük mekanik ve fiziksel özellikler gibi dezavantajlara sahiptir.
📊
Key Findings & Data:Bu çalışmanın amacı, mikrodalga enerjisi ile polimerize olan akrilik rezin içerisine ağırlıkça % 1, 3 ve 5 oranlarında Al2O3, SiO2 ve TiO2 nanopartikülleri ilavesinin yüzey sertliği ve yüzey pürüzlülüğü gibi mekanik ve fiziksel özellikleri üzerine etkisini değerlendirmektir.
💡
Conclusion & Impact:Keywords: Polymethylmethacrylate, Nanoparticle, Surface roughness, Surface hardness.
🔬Design:Experimental Field Trial
📍Scope:Comprehensive Sample
⚙️Variables:Polimetilmetakrilat · Nanopartikül · Yüzey pürüzlülüğü

Özet

Amaç: PMMA, protetik diş hekimliğinde protez kaide materyali olarak yaygın kullanılmasına rağmen düşük mekanik ve fiziksel özellikler gibi dezavantajlara sahiptir. Bu çalışmanın amacı, mikrodalga enerjisi ile polimerize olan akrilik rezin içerisine ağırlıkça % 1, 3 ve 5 oranlarında Al2O3, SiO2 ve TiO2 nanopartikülleri ilavesinin yüzey sertliği ve yüzey pürüzlülüğü gibi mekanik ve fiziksel özellikleri üzerine etkisini değerlendirmektir. Gereç ve Yöntem: Çalışmamızda üretici firmanın önerileri dikkate alınarak, on farklı grup için toplam yetmiş akrilik rezin örnek (65×10×3 mm) hazırlanmıştır (n=7). Polisaj ve cilalama işlemleri yapıldıktan sonra yüzey pürüzlülük değerleri (Ra) profilometre cihazı ile, yüzey sertliği değerleri ise Rockwell R testi ile ölçülmüştür. Elde edilen verilerin homojenitesi Kolmogorov-Smirnov testi ile değerlendirildikten sonra iki yönlü varyans analizi ve Tukey HSD testleri kullanılmıştır (α=0.05). Bulgular: Yüzey pürüzlülüğü değerleri açısından, %1 oranında nanopartikül ilave edilen grubun pürüzlülük değerleri kontrol grubuna oldukça yakın bulunurken (0.28-0.29), %3 ve %5 oranında ilave yapılan grupların pürüzlülük değerleri mikroorganizma tutulumu için kritik değerden (0.2 µm) çok yüksek (0.46-0.84) bulunmuştur. Yüzey sertliği değerleri açısından ise nanopartikül ilavesi sonucunda yüzey sertlik değerleri artarken en yüksek değerler %5 oranında ilave edilen gruplarda bulunmuştur (p < 0.05). Sonuç: Bu çalışmanın sınırları dahilinde, PMMA’a nanopartikül ilavesi ile mekanik özellikleri geliştirilebilir, ancak nanopartikül ilave yüzdesi arttıkça (%3 ve %5) PMMA’nın yüzey pürüzlülük değerlerinin artması ideal doldurucu oranının %1 olduğunu göstermektedir. Anahtar kelimeler: Polimetilmetakrilat, Nanopartikül, Yüzey pürüzlülüğü, Yüzey sertliği. Evaluation of mechanical and physical properties of micro-waved acrylic resin reinforced with different nanoparticles Abstract Purpose: PMMA has disadvantages such as low mechanical and physical properties although it is widely used as prosthetic base material in prosthetic dentistry. The aim of this study is to evaluate the effects of adding Al2O3, SiO2 and TiO2 nanoparticles in ratios of 1, 3 and 5 wt% to micro-waved acrylic resins on the mechanical and physical properties such as surface hardness and surface roughness. Material and Method: A total of seventy acrylic resin specimens (65×10×3 mm) were prepared in different ten groups according to manufacturer’s instructions (n=7). After polishing surface roughness values ​​were measured by profilometer, and surface hardness values ​​were measured by Rockwell R test. Homogeneity of the obtained data was assessed by Kolmogorov-Smirnov test followed by Two-way ANOVA and Tukey HSD test (α=0.05). Results: In terms of surface roughness values, the roughness of the groups added with 1% nanoparticle were very close to control group (0.28-0.29), whereas roughness values ​​of 3% and 5% addition groups were found to be very high (0.46-0.84) from the critical value (0.2 μm) for microorganism involvement. In terms of surface hardness values, surface hardness values were increased as a result of nanoparticle addition, whereas the highest values were foud in 5% addition groups (p < 0.05). Conclusion: Within the limitations of this study, the mechanical properties can be improved with the addition of nanoparticles to PMMA, but the increase in the surface roughness values of PMMA with increasing nanoparticle addition ratio (3% and 5%) suggests that the ideal filler ratio is 1%. Keywords: Polymethylmethacrylate, Nanoparticle, Surface roughness, Surface hardness.

🔖

Cite This Article

KARCI, M., DEMİR, N., YAZMAN, Ş. (2020). FARKLI NANOPARTİKÜLLERLE GÜÇLENDİRİLEN MİKRODALGA ENERJİSİ İLE POLİMERİZE OLAN AKRİLİK REZİNİN MEKANİK VE FİZİKSEL ÖZELLİKLERİNİN DEĞERLENDİRİLMESİ. Current Research in Dental Sciences, Cilt: 30 Sayı: 1, 101–106. https://ajindex.com/articles/900986

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (16)

  1. Alla R, Raghavendra K, Vyas R, Konakanchi A. Conventional and contemporary polymers for the fabrication of denture prosthesis: part I–overview, composition and properties. Int J Appl Dent Sci 2015;1:82-9
  2. Anusavice KJ. Dental Polymers. In: Phillips' Science of Dental Materials. 11th ed. St. Louis, Missouri: Saunders Elsevier; 2003. p. 75-98
  3. Memon MS, Yunus N, Razak AA. Some mechanical properties of a highly cross-linked, microwave-polymerized, injection-molded denture base polymer. Int J Prosthodont 2001;14(3):214-8
  4. Kakaboura A, Fragouli M, Rahiotis C, Silikas N. Evaluation of surface characteristics of dental composites using profilometry, scanning electron, atomic force microscopy and gloss-meter. J Mater Sci Mater Med 2007;18(1):155-63
  5. Joniot S, Salomon JP, Dejou J, Gregoire G. Use of two surface analyzers to evaluate the surface roughness of four esthetic restorative materials after polishing. Oper Dent 2006;31(1):39-46
  6. O'Brien WJ. Dental Materials and Their Selection. 3th ed. Canada: Quintessence Publishing Company; 2002. p. 145-67
  7. Sakaguchi RL, Powers JM. Craig's restorative dental materials. 13th ed. Mosby: Elsevier Health Sciences; 2012. p. 112-34
  8. O'Brien WJ. Dental Materials and Their Selection. 2nd ed. Chicago: Quintessence Publishing Company; 1997. p. 79-95, 259-72
  9. Craig RG, Powers JM, Wataha JC. Dental Polymers. In: Dental Materials, Properties and Manipulatio. 12th ed. St. Louis: Mosby; 2000. p. 145-76
  10. Vallittu PK. A review of methods used to reinforce polymethyl methacrylate resin. J Prosthodont 1995;4(3):183-7
  11. Tacir I, Kama J, Zortuk M, Eskimez S. Flexural properties of glass fibre reinforced acrylic resin polymers. Aust Dent J 2006;51(1):52-6
  12. Salman TA, Khalaf HA. The influence of adding of modified ZrO2-TiO2 nanoparticles on certain physical and mechanical properties of heat polymerized acrylic resin. J Bagh Coll Dent 2015;3:33-9
  13. Alhareb A, Akil H, Ahmad Z. Influence of Al2O3/Y-TSZ mixture as filler loading on the radiopacity of PMMA denture base composites. Procedia Chem 2016; 19:646-50
  14. Allaker R. The use of nanoparticles to control oral biofilm formation. J Dent Res 2010;89(11):1175-86
  15. Hajipour MJ, Fromm KM, Ashkarran AA, Jimenez de Aberasturi D, de Larramendi IR, Rojo T, et al. Antibacterial properties of nanoparticles. Trends Biotechnol 2012;30(10):499-511
  16. Lainović T, Blažić L, Potran M. Nanotechnology in dentistry: current state and future perspectives. Stomatol Glas