SavedAdd your journal

Journals / Sigma Journal of Engineering and Natural Sciences / 2018 / Cilt: 36 Sayı: 3

OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING

Kürşad Oğuz OSKAY
Bilal DEMİREL
Pages
795–802
Publication Date
2018-09-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:NiCrAl composite coatings were obtained by electro-deposition under direct current (DC) conditions from a Watt’s bath containing suspended Cr, Al particles.
📊
Key Findings & Data:Mathematical models were developed to simulate the electroplated composite coating.
💡
Conclusion & Impact:Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Electrodeposition · NiCrAl composite coating · RSM

Abstract

NiCrAl composite coatings were obtained by electro-deposition under direct current (DC) conditions from a Watt’s bath containing suspended Cr, Al particles. Mathematical models were developed to simulate the electroplated composite coating. The models allow composition of the coatings to be predicted. The predicted values obtained were close to the experimental values, indicating the suitability of the models. The prediction made using Response Surface Method (RSM) was also supported by SEM photos. Three-dimensional surface plots were helpful for predicting results by performing only limited set of experiments.

🔖

Cite This Article

OSKAY, K. O., DEMİREL, B. (2018). OPTIMIZING THE COMPOSITION OF ELECTROPLATED NiCrAl COMPOSITE COATING. Sigma Journal of Engineering and Natural Sciences, Cilt: 36 Sayı: 3, 795–802. https://ajindex.com/articles/897733

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Aruna S. T., Roy S., Sharma A., Savitha G., and Grips V. K. W. (2014) Cost-effective wear and oxidation resistant electrodeposited Ni – pumice coating, Surf. Coat. Technol., vol. 251, pp. 201–209
  2. Masoudi M., Hashim M., Kamari H. M., and Salit M. S. (2012) Fabrication and characterization of Ni–SiC–Cr nanocomposite coatings, Appl. Nanosci., vol. 3, no. 4, pp. 357–362
  3. Liu H. and Chen W. (2005) Electrodeposited Ni-Al composite coatings with high Al content by sediment co-deposition, Surf. Coatings Technol., vol. 191, no. 2–3, pp. 341–350
  4. Borkar T. and Harimkar S. P. (2011) Effect of electrodeposition conditions and reinforcement content on microstructure and tribological properties of nickel composite coatings, Surf. Coatings Technol., vol. 205, no. 17–18, pp. 4124–4134
  5. Vaezi M. R., Sadrnezhaad S. K., and Nikzad L. (2008) Electrodeposition of Ni–SiC nano-composite coatings and evaluation of wear and corrosion resistance and electroplating characteristics, Colloids Surfaces A Physicochem. Eng. Asp., vol. 315, no. 1–3, pp. 176–182
  6. Srivastava M., Siju, Balaraju J. N., and Ravisankar B. (2015) Development and High Temperature Property Evaluation of Ni-Co-Cr-Al Composite Electroforms, J. Mater. Eng. Perform., vol. 24, no. 5, pp. 1937–1944
  7. Ul-Hamid A., Dafalla H., Al-Yousef F., and Mohammed A. I. (2014) Microstructural study of NiCrAlY electrodeposits, Prot. Met. Phys. Chem. Surfaces, vol. 50, no. 5, pp. 679–687
  8. Bahamirian M. (2013) An Investigation on Effect of Bond Coat Replacement on Hot Corrosion Properties of Thermal Barrier Coatings, Iran. J. Mater. Sci. Eng., vol. 10, no. 3, pp. 12–21
  9. Bates B. L., Zhang L. Z., and Zhang,Y. (2015) Electrodeposition of Ni matrix composite coatings with embedded CrAlY particles, Surf. Eng., vol. 31, no. 3, pp. 202–208
  10. Haynes J. A., Ferber M. K., and Porter W. D. (2000) Thermal Cycling Behavior of Plasma-Sprayed Thermal Barrier Coatings with Various MCrAIX Bond Coats, J. Therm. Spray Technol., vol. 9, no. March, pp. 38–48
  11. Zhu C., Li P., and Wu X. Y. (2015) A study of the diffusion and pre-oxidation treatment on the formation of Al2O3 ceramic scale on NiCrAlY bond-coat during initial oxidation process, Ceram. Int., vol. 42, pp. 7708–7716,
  12. Ajdelsztajn L., Tang F., Kim G. E., Provenzano V., and Schoenung J. M. (2005) Synthesis and Oxidation Behavior of Nanocrystalline MCrAlY Bond Coatings, J. Therm. Spray Technol., vol. 14, no. 1, pp. 23–30
  13. Şahin Y. and Öksüz K. E.