Journals / European Mechanical Science / 2023 / Cilt: 7 - Sayı: 1

Numerical investigation of different combustion chamber on flow, combustion characteristics and exhaust emissions

Pages
7–15
Publication Date
2023-03-20
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

According to the results obtained from the analyzes, the new combustion chamber system (NCCS) geometry provided a 40.3% reduction in soot emissions while NO emissions increased slightly with the 8-cavity bowl geometry created in the combustion chamber compared to the standard combustion chamber system (SCCS).

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study includes numerical analysis of diesel engine with different bowl geometry. 3D CFD analyzes of the engine with asymmetrical piston geometry were performed in Ansys Forte software.
📊
Key Findings & Data:It has been tested where the maximum torque is obtained as the operating condition at 2000 rpm.
💡
Conclusion & Impact:According to the results obtained from the analyzes, the new combustion chamber system (NCCS) geometry provided a 40.3% reduction in soot emissions while NO emissions increased slightly with the 8-cavity bowl geometry created in the combustion chamber compared to the standard combustion chamber system (SCCS).
🔬Design:Research Article
📍Scope:2000 Verileri
⚙️Variables:Diesel engine · Bowl geometry · Combustion analysis

Abstract

This study includes numerical analysis of diesel engine with different bowl geometry. 3D CFD analyzes of the engine with asymmetrical piston geometry were performed in Ansys Forte software. In the study, a single-cylinder, four-stroke and direct injection diesel engine was used. It has been tested where the maximum torque is obtained as the operating condition at 2000 rpm. According to the results obtained from the analyzes, the new combustion chamber system (NCCS) geometry provided a 40.3% reduction in soot emissions while NO emissions increased slightly with the 8-cavity bowl geometry created in the combustion chamber compared to the standard combustion chamber system (SCCS). Increasing air velocity and turbulent kinetic energy (TKE) values in the combustion chamber affected the evaporation levels of the fuels. As a result, the improved mixture formation caused a decrease in incomplete combustion products (CO, HC and soot). The NCCS geometry according to SCCS type, an increase of approximately 4.2% occurred in the calculated squish rates. It has been observed that the increase in the bowl surface area causes the combustion and thus the temperature to spread over a larger area on the piston.

🔖

Cite This Article

TEMİZER, İ., CİHAN, Ö., ÖNCÜOĞLU, Ö. (2023). Numerical investigation of different combustion chamber on flow, combustion characteristics and exhaust emissions. European Mechanical Science, Cilt: 7 - Sayı: 1, 7–15. https://ajindex.com/articles/885938

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Jaichandar, J., Annamalai, K. (2012). Influences of re-entrant combustion chamber geometry on the performance of Pongamia biodiesel in a DI diesel engine. Energy, 44(1): 633-640. https://doi.org/10.1016/j.energy.2012.05.029
  2. Challen, B., Barnescu, R. (1999). Diesel engine reference book. England: Society of Automotive Engineers; Bath Press.
  3. Montajir, R., Tsunemoto, H., Ishitani, H., Minami, T., (2000). Fuel spray Behavior in a small DI Diesel engine: effect of combustion chamber geometry. SAE Technical Paper, 2000-01-0946: 1-12. https://doi.org/10.4271/2000-01-0946.
  4. Kalay, İ. (2011). Investigation of piston bowl in diesel engines, M.Sc thesis, Istanbul Technical University, Institute of science and technology, Istanbul, Turkey. Varun, Singh, P., Tiwari, S.K., Singh, R., Kumar, N., (2017). Modification in combustion chamber geometry of CI engines for suitability of biodiesel: A review. Renewable and Sustainable Energy Reviews, 79: 1016-1033. https://doi.org/10.1016/j.rser.2017.05.116
  5. Saito, T., Daisho, Y., Uchida, N., Ikeya, N. (1986). Effects of Combustion Chamber Geometry on Diesel Combustion. SAE Technical Paper, 861186: 71-81. https://doi.org/10.4271/861186.
  6. Yaliwal, V.S., Banapurmath, N.R., Gireesh, N.M., Hosmath, R.S., Donateo, T., Tewari, P.G. (2016). Effect of nozzle and combustion chamber geometry on the performance of a diesel engine operated on dual fuel mode using renewable fuels. Renewable Energy, 93: 483-501. https://doi.org/10.1016/j.renene.2016.03.020
  7. Bapu, B.R.R., Saravanakumar, L., Prasad, B.D. (2017). Effects of combustion chamber geometry on combustion characteristics of a DI diesel engine fueled with calophyllum inophyllum methyl ester. Journal of the Energy Institute, 90(1): 82-100, https://doi.org/10.1016/j.joei.2015.10.004
  8. Sener, R., Yangaz, M.U., Gul, M.Z. (2020). Effects of injection strategy and combustion chamber modification on a single-cylinder diesel engine. Fuel, 266: 1-15. https://doi.org/10.1016/j.fuel.2020.117122
  9. Dimitriou, P., Wang, W., Peng, Z. (2015). A piston geometry and n ozzle spray angle investigation in a DI diesel engine by quantifying the air-fuel mixture. International Journal of Spray and Combustion Dynamics, 7(1): 1-24. https://doi.org/10.1260/1756-8277.7.1.1
  10. Sener, R., Ozdemir, M.R., Yangaz, M.U. (2019). Influence of piston bowl geometry on combustion and emission characteristics. Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, 233(5): 576-587. https://doi.org/10.1