Journals / Politeknik Dergisi / 2022 / Cilt: 25 - Sayı: 3

The Effect of Fiber Type and Ratio on the Physical and Mechanical Properties of Marble Powder Added Fiber Concrete

Mermer Tozu Katkılı Lifli Betonun Fiziksel ve Mekanik Özeliklerine Lif Tipi ve Oranının Etkisi

Pages
1143–1155
Publication Date
2022-10-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The highest mechanical and physical properties were given by 1.00% steel fiber and 0.35% macro synthetic fiber concretes.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, it is aimed to determine the effect of steel and macro synthetic fibers used in different ratios and types on the physical and mechanical properties of concrete.
📊
Key Findings & Data:For this purpose; Macro synthetic fiber was used at 0.25%, 0.30% and 0.35% by volum4, steel fiber at 0.50%, 0.75% and 1.00% by volume.
💡
Conclusion & Impact:The highest mechanical and physical properties were given by 1.00% steel fiber and 0.35% macro synthetic fiber concretes.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Lifli beton · eğilme dayanımı · aşınma dayanımı

Abstract

In this study, it is aimed to determine the effect of steel and macro synthetic fibers used in different ratios and types on the physical and mechanical properties of concrete. For this purpose; Macro synthetic fiber was used at 0.25%, 0.30% and 0.35% by volum4, steel fiber at 0.50%, 0.75% and 1.00% by volume. Chemical additives and marble powder were used in fixed proportions. In the study, the water / cement ratio was taken as 0.54 constant according to the fiber concrete TS 802 mixture. In this research, beams of 10 × 10 × 40 cm and 15 cm cube samples were produced for fresh and hardened concrete properties. The effect of fiber type and ratio was investigated by performing physical and mechanical tests on the produced samples. As a result of the study, as the fiber ratio of fiber mixes in fresh concrete increased, workability and unit volume weights decreased. As a result, as the fiber ratio in fresh concrete increases, the fiber ratio has negatively affected the workability and the unit volume weights decreased. In hardened concrete; In hardened concrete; As the fiber ratio increased, the initial crack stress and bending stress increased. The highest mechanical and physical properties were given by 1.00% steel fiber and 0.35% macro synthetic fiber concretes.

Özet

Yapılan bu çalışmada farklı oran ve tiplerde kullanılan çelik ve makro sentetik liflerin betonun fiziksel ve mekanik özelliklerine etkisinin belirlenmesi amaçlanmıştır. Bu amaçla; Makro sentetik lif hacimce %0.25, %0.30 ve %0.35 oranında, çelik lif hacimce % 0.50, % 0.75 ve % 1.00 oranında kullanılmıştır. Çalışmada lifli betonların karışım hesabı TS 802’ esas alınarak yapılmış ve su/çimento oranı 0.54 sabit alınmıştır. Bu araştırmada taze ve sertleşmiş beton özellikleri için 10 × 10 × 40 cm boyutlarında kiriş ve 15 cm’lik küp numuneler üretilmiştir. Üretilen numuneleri üzerinde fiziksel ve mekanik deneyler yapılarak lif tipi ve oranını etkisi araştırılmıştır. Çalışma sonucunda taze betonda lifli karışımlar da lif oranı artıkça, işlenebilirlik ve birim hacim ağırlıklarını da azalmıştır. Sonuç olarak taze betonda lifli karışımlar da lif oranı artıkça, işlenebilirliği olumsuz olarak etkilerken birim hacim ağırlıklarını da düşürmüştür. Sertleşmiş betonda ise; Lif oranı arttıkça ilk çatlak gerilmesi ve eğilme gerilmesi arttırmıştır. En yüksek mekanik ve fiziksel özellikleri %1.00 çelik lifli, %0.35 makro sentetik lifli betonlar vermiştir.

🔖

Cite This Article

ŞİMŞEK, O., DEMİR, Ş. (2022). The Effect of Fiber Type and Ratio on the Physical and Mechanical Properties of Marble Powder Added Fiber Concrete. Politeknik Dergisi, Cilt: 25 - Sayı: 3, 1143–1155. https://ajindex.com/articles/862642

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Rossi,P., “Steel fiber reinforced concrete an example of french research’’, Materials Janural, 91, 3, (1994)
  2. Barr,B.I.G., Evans, G.,J., ‘’Fracture characteristics of fibre reinforced lightweight concrete’’, Rilem Technical Committee 49 TFR 17, 401-407, (1986)
  3. Hasan, M.J., Afroz, M., And Mahmud, H.M.I., “An experimental investigation on mechanical behavior of macro synthetic fiber reinforced concrete”, International Journal of Civil Environmental Engineering, 11, 121-12, (2011)
  4. Falkner, H.,Huang, Z., Teutsch, M., “Comparative study of plain and steel fibre reinforced concrete graund slabs’’, Concrete International, 45-51, (1995)
  5. Follıard, K., Sutfın, D., Turner, R., Whıtney, D.P., “Fiber in continuously reinforced concrete pavements”, Final Report Submitted to the Texas Department of Transportation, Report No.0-4392-2, (2006)
  6. Yılmaz, Ü.S., “Eksenel yük etkisindeki çelik tel fiber takviyeli etriyeli betonarme kolonların davranışı”, Yüksek Lisans Tezi, Selçuk Üniversitesi Fen Bilimleri Enstitüsü, (2001)
  7. Rıchardson, A.E., Coventry, K. Landless, S., “Synthetic and steel fibers in concrete with regard to equal toughness”, Structural Survey, 28, 355-369, (2010)
  8. Yehıa, S., Douba, A., Abdullahı, O., Farrag, S., “Mechanical and durability evaluation of fiber-reinforced self-compacting concrete”, Construction and Building Materials, 121, 120-133, (2016)
  9. Korkut, F., Türkmenoğlu, Z.F. Taymuş, R.B., Güler, S., “Çelik ve sentetik liflerin kendiliğinden yerleşen betonların taze ve mekanik özellikleri üzerine etkisi” ÖHÜ Müh. Bilim. Dergisi 6(2), 560-570, (2017). [10]Şimşek O., Toklu K. ve Ünal M.T, “Çelik liflerin geometrik şeklinin ve oranının beton özelliklerine etkisinin araştırılması ”, Politeknik Dergisi, (24), 409-415, (2021). [11]Şimşek O., “Lifli betonlarda optimum silis dumanı ikame oranının belirlenmesi”, Politeknik Dergisi, 23(3), 729-735, (2020)
  10. Yıldırm, S.T.,Ekinci, C.E., “Çelik, cam ve polipropilen lifli betonlarda donma-çözülme etkilerinin araştırılması’’, Fırat Üniversitesi Fen ve Mühendislik Bilimleri Dergisi 18(3), 359-366, (2006)
  11. Shah, S.P., Rangan, B.V., “Fiber reinforced concrete properties”, Journal Proceedings, 68(2), 126-137,(1971)
  12. Barr, B.I.G., Liu, K., “Fracture of GRC materials”, International Journal of Cement Composites and Lightweight Concrete, 4(3), 163-171, (1982)
  13. Gökçe M. “Determining the physical properties of polymer in different admixtures used for self-compacting cemen