Journals / Politeknik Dergisi / 2022 / Cilt: 25 - Sayı: 3

Investigation of Compatibility Between Design and Additively Manufactured Parts of Functionally Graded Porous Structures

İşlevsel Geçişli Gözenekli Yapıların Tasarımı ve Eklemeli Üretilen Parçalar Arasındaki Uyumluluğun Araştırılması

Pages
1069–1082
Publication Date
2022-10-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

According to the results obtained from micro-CT, an average increase of 150-300 μm was observed on the column thicknesses of all functionally graded porous structures.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, deviations for the porosity level of the Ti-6Al-4V functionally graded porous structures for three different cell structures were investigated.
📊
Key Findings & Data:According to the results obtained from micro-CT, an average increase of 150-300 μm was observed on the column thicknesses of all functionally graded porous structures.
💡
Conclusion & Impact:It has been determined that the porosity of the manufactured parts was deviated between 5.71%-10.54% for cubic, 8.59%-12.39% for octahedroid, and 13%-16.49% for diamond structures compared to the design values.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Eklemeli üretim · gözeneklilik · işlevsel basamaklandırılmış yapı

Abstract

In this study, deviations for the porosity level of the Ti-6Al-4V functionally graded porous structures for three different cell structures were investigated. For this purpose, functionally graded porous structures are designed and produced by selective laser melting (SLM). It is also aimed to investigate the effects of unit cell structure, unit cell size, and column (strut) thickness on the porosity deviation level. The specimens were scanned at micro-computed tomography (micro-CT) to determine the structure dimensions after production. According to the results obtained from micro-CT, an average increase of 150-300 μm was observed on the column thicknesses of all functionally graded porous structures. It has been observed that the horizontal columns of cubic and octagonal structures have sagging due to metal melting during production. It has been determined that the porosity of the manufactured parts was deviated between 5.71%-10.54% for cubic, 8.59%-12.39% for octahedroid, and 13%-16.49% for diamond structures compared to the design values.

Özet

Bu çalışmada, Ti-6Al-4V geçişli gözenekli yapıların üç farklı birim hücre yapısı için gözeneklilik oranlarındaki sapmalar araştırılmıştır. Bu amaçla, işlevsel geçişli hücresel yapılar tasarlanmış ve seçici lazer ergitme yöntemiyle üretilmiştir. Ayrıca birim hücre yapısının, birim hücre boyutunun ve kolon (dikme) kalınlığının gözenek boyutlarındaki sapma seviyesi üzerindeki etkilerinin araştırılması amaçlanmıştır. Numuneler, üretim sonrası yapı boyutunu belirlemek için mikro bilgisayarlı tomografide (mikro-BT) taranmıştır. Mikro-BT'den elde edilen sonuçlara göre, geçişli gözenekli tüm hücre yapılarının kolon kalınlık değerlerinde ortalama 150-300 μm arasında değişen artışlar gözlenmiştir. Kübik ve sekizyüzlü yapıların yatay kolonlarında üretim sırasında ergiyen metal sebebiyle sarkmalar oluştuğu gözlenmiştir. Üretilen parçaların gözenekliliği, tasarım değerleri ile karşılaştırıldığında kübik yapıda %5.71-%10.54, sekizyüzlü yapıda %8.59-12.39 ve elmas yapıda %13-16.49 aralıklarında değişen oranlarda sapmaların oluştuğu tespit edilmiştir.

🔖

Cite This Article

DURSUN, A. M., TÜZEMEN, M. Ç., SALAMCI, E., YILMAZ, O., ÜNAL, R. (2022). Investigation of Compatibility Between Design and Additively Manufactured Parts of Functionally Graded Porous Structures. Politeknik Dergisi, Cilt: 25 - Sayı: 3, 1069–1082. https://ajindex.com/articles/862635

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (12)

  1. Zhang X. Y., Fang G., Leeflang S., Zadpoor A. A., and Zhou J., "Topological design, permeability and mechanical behavior of additively manufactured functionally graded porous metallic biomaterials", Acta Biomaterialia, 84: 437–452, (2019)
  2. Zhang X. Y., Yan X. C., Fang G., and Liu M., "Biomechanical influence of structural variation strategies on functionally graded scaffolds constructed with triply periodic minimal surface", Additive Manufacturing, 32: 101015, (2020)
  3. Zhao D., Huang Y., Ao Y., Han C., Wang Q., Li Y., Liu J., Wei Q., and Zhang Z., "Effect of pore geometry on the fatigue properties and cell affinity of porous titanium scaffolds fabricated by selective laser melting", Journal of the Mechanical Behavior of Biomedical Materials, 88: 478–487, (2018)
  4. Dallago M., Fontanari V., Winiarski B., Zanini F., Carmignato S., and Benedetti M., "Fatigue properties of Ti6Al4V cellular specimens fabricated via SLM: CAD vs real geometry", Procedia Structural Integrity, 7: 116–123, (2017)
  5. Ali H., Ghadbeigi H., and Mumtaz K., "Processing Parameter Effects on Residual Stress and Mechanical Properties of Selective Laser Melted Ti6Al4V", Journal of Materials Engineering and Performance, 27: 4059–4068, (2018)
  6. Aydın İ., and Engin F., "Hydroxyapatite Coating on Ti6Al4V Alloy Surface Through Biomimetic Method Using Glycolic Acid - Sodium Gluconate Buffer System and Examination of Properties of the Coating", Journal of Polytechnic, 20: 993–1001, (2017)
  7. Subaşi M., Safarian A., and Karataş Ç., "An Investigation of Sintering Parameters of Ti-6Al-7Nb Fabricated by Powder Injection Molding", Journal of Polytechnic, 30: 502–512, (2017)
  8. Subasi O., Oral A., and Lazoglu I., "A novel adjustable locking plate (ALP) for segmental bone fracture treatment", Injury, 50: 1612–1619, (2019)
  9. Wu L., and Zhang J., "Phase Field Simulation of Dendritic Solidification of Ti-6Al-4V During Additive Manufacturing Process", Jom, 70: 2392–2399, (2018)
  10. Challis V. J., Xu X., Zhang L. C., Roberts A. P., Grotowski J. F., and Sercombe T. B., "High specific strength and stiffness structures produced using selective laser melting", Materials and Design, 63: 783–788, (2014)
  11. Gibson L. J., and Ashby M. F., Cellular solids: Structure and properties, second edition. Cell Solids Struct Prop Second Ed
  12. Mazur M., Leary M., McMillan M., Sun S., Shidid D., and Brandt M., "Mechanical properties of Ti6Al4V and AlSi12Mg lattice structures manufactured by Select