Journals / Politeknik Dergisi / 2022 / Cilt: 25 - Sayı: 3

Numerical Investigation of Radius Dependent Solidity Effect on H-Type Vertical Axis Wind Turbines

Yarıçapa Bağlı Katılık Oranının bir H-Tip Dikey Eksenli Rüzgâr Türbinine Etkisinin Sayısal Olarak İncelenmesi

Pages
1007–1019
Publication Date
2022-10-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Results show that the higher efficiency can be obtained both in low Type Speed Ratio (TSR) values with the increase of solidity and in high TSR values with the decrease in solidity.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, radius-dependent solidity effect to the aerodynamic characteristic of a three bladed H-rotor Darrieus wind turbine consisting of NACA 0021 profile blades was investigated numerically in Ansys Fluent 14.1 software.
📊
Key Findings & Data:Results show that the higher efficiency can be obtained both in low Type Speed Ratio (TSR) values with the increase of solidity and in high TSR values with the decrease in solidity.
💡
Conclusion & Impact:Power coefficient (Cp) has been enhanced as 4.25% with 0.75 m (M1) and Cp has been reduced as 0.57% with 1.25 m (M3) rotor radius according to 1 m rotor radius (M2), respectively.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Sayısal Analiz · darrieus rüzgar türbini · H-rotor

Abstract

In this study, radius-dependent solidity effect to the aerodynamic characteristic of a three bladed H-rotor Darrieus wind turbine consisting of NACA 0021 profile blades was investigated numerically in Ansys Fluent 14.1 software. After achieving independence from the mesh, the numerical method was validated with the experimental data and then numerical analyses were performed for different solidity values. Results show that the higher efficiency can be obtained both in low Type Speed Ratio (TSR) values with the increase of solidity and in high TSR values with the decrease in solidity. Power coefficient (Cp) has been enhanced as 4.25% with 0.75 m (M1) and Cp has been reduced as 0.57% with 1.25 m (M3) rotor radius according to 1 m rotor radius (M2), respectively.

Özet

Bu çalışmada yarıçapa bağlı olarak değiştirilen katılık oranının, NACA 0021 kanat profiline sahip 3 kanatlı H-tip dikey eksenli rüzgar türbini aerodinamik performansına olan etkisi sayısal olarak Ansys – Fluent 14.1 yazılımında incelenmiştir. Meshten bağımsızlığa ulaşıldıktan sonra kullanılan sayısal methodlar deneysel çalışmadan elde edilen sonuçlar ile doğrulanmış ve farklı katılık oranlarında sayısal analizler tekrarlanmıştır. Sonuçlar incelendiğinde, katılık oranının artması ile birlikte düşük kanat uç hız oranlarında (TSR), katılık oranının azalması ile birlikte ise yüksek TSR değerlerinde daha yüksek aerodinamik verim elde edileceği görülmüştür. Gözlemlenen en büyük güç katsayıları, 1 m yarıçapa sahip olan turbine göre (Cp) 0.75 m yarıçapa sahip olan (M1) türbinde %4.25 artmış, 1.25 m yarıçapa sahip olan (M3) türbinde ise % 0.57 azalmıştır.

🔖

Cite This Article

KAYA, A. F., TANÜRÜN, H. E., ACIR, A. (2022). Numerical Investigation of Radius Dependent Solidity Effect on H-Type Vertical Axis Wind Turbines. Politeknik Dergisi, Cilt: 25 - Sayı: 3, 1007–1019. https://ajindex.com/articles/862630

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Naccache G. and Paraschivoiu M., “Parametric study of the dual vertical axis wind turbine using CFD”, J Wind Eng Ind Aerodyn, 172:244–55, (2018)
  2. Kragten A., “The Darrieus Rotor, A Vertical Axis Wind Turbine (VAWT) with Only A Few Advantages and Many Disadvantages”, Sint-Oedenrode, (2004)
  3. Wong KH., Chong WT., Poh SC., Shiah YC., Sukiman NL. and Wang CT., “3D CFD simulation and parametric study of a flat plate deflector for vertical axis wind turbine”, Renew Energy, 129:32–55, (2018)
  4. Li Q., Maeda T., Kamada Y., Murata J., Furukawa K. and Yamamoto M., “Effect of number of blades on aerodynamic forces on a straight-bladed Vertical Axis Wind Turbine”, Energy, 90:784–95, (2015)
  5. Rezaeiha A., Montazeri H. and Blocken B., “Towards optimal aerodynamic design of vertical axis wind turbines: Impact of solidity and number of blades”, Energy, 165:1129–48, (2018)
  6. Abu-el-yazied TG., Ali AM., Al-ajmi MS. and Hassan IM., “Effect of Number of Blades and Blade Chord Length on the Performance of Darrieus Wind Turbine”, Am J Mech Eng, 2:16–25, (Autom 2015)
  7. Sunyoto A., Wenehenubun F., Sutanto H., “The effect of number of blades on the performance of H-Darrieus type wind turbine”, International Conference on QiR, 192–6, (2013)
  8. Castelli MR., Betta S. De., Benini E., “Effect of Blade Number on a Straight-Bladed Vertical-Axis Darreius Wind Turbine”, World Acad Sci Eng Technol, 6:256–62, (2012)
  9. Yang Y., Guo Z., Song Q., Zhang Y., Li Q., “Effect of blade pitch angle on the aerodynamic characteristics of a straight-bladed vertical axis wind turbine based on experiments and simulations”, Energies, 11, (2018)
  10. Zhang LX., Liang Y. Bin., Liu. XH., Guo J., “Effect of blade pitch angle on aerodynamic performance of straight-bladed vertical axis wind turbine”, J Cent South Univ, 21:1417–27, (2014)
  11. Fiedler AJ. and Tullis S., “Blade offset and pitch effects on a high solidity vertical axis wind turbine”, Wind Eng, 33:237–46, (2009)
  12. Bogateanu R., Dumitrache A., Dumitrescu H., Stoica CI., “Reynolds number efects on the aerodynamic performance of small VAWTs”, UPB Sci Bull Ser D Mech Eng, 76:25–36, (2014)
  13. Gosselin R., Dumas G. and Boudreau M., “Parametric study of H-Darrieus vertical-axis turbines using CFD simulations”, J Renew Sustain Energy, 8, (2016)
  14. Bachant P. and Wosnik M., “Effects of reynolds number on the energy conversion and near-wake dynamics of a high solidity vertical-axis cross-flow turbine”, Energies, 9:1–18,