Journals / International Journal of Innovative Engineering Applications / 2022 / Cilt: 6 - Sayı: 2

Investigation of Press Brake Punches and Dies Produced by Casting Method and From Manganese Steel Material in Terms of Machinability

Döküm Yöntemi ile Manganlı Çelik Malzemeden Üretilen Abkant Pres Zımba ve Dişi Kalıpların İşlenebilirlik Yönünden İncelenmesi

Pages
276–285
Publication Date
2022-12-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

At the end of the study, it was concluded that the punches and dies manufactured from manganese steel produced in foundry and widely found are alternatives compared to available AISI 4140 steel molds in terms of machinability.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Punches and dies employed in sheet metal “V” bending have been obtained generally from stock materials, AISI 4140 and EN C45 (Ck 45), in industrial applications through machining.
📊
Key Findings & Data:In this study, the experimental samples from both AISI 4140 and manganese steel were machined at different cutting parameters (cutting speed, feed rate, cutting depth), hence they were compared by analyzing with regard to chip morphology, cutting tool edge wear and surface roughness.
💡
Conclusion & Impact:At the end of the study, it was concluded that the punches and dies manufactured from manganese steel produced in foundry and widely found are alternatives compared to available AISI 4140 steel molds in terms of machinability.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:“V” bükme · İşlenebilirlik · Zımba ve dişi kalıplar

Abstract

Punches and dies employed in sheet metal “V” bending have been obtained generally from stock materials, AISI 4140 and EN C45 (Ck 45), in industrial applications through machining. The fact that local and different manufacturing methods have been applied in manufacturing these punches and dies has gained great significance in terms of external dependency and economy. The purpose of this study is to manufacture punches and dies used in “V” bending process from manganese steel via cast method and compare the newly obtained molds with presently used molds in terms of machinability and surface roughness. In this study, the experimental samples from both AISI 4140 and manganese steel were machined at different cutting parameters (cutting speed, feed rate, cutting depth), hence they were compared by analyzing with regard to chip morphology, cutting tool edge wear and surface roughness. At the end of the study, it was concluded that the punches and dies manufactured from manganese steel produced in foundry and widely found are alternatives compared to available AISI 4140 steel molds in terms of machinability.

Özet

Sac metal bükmede kullanılan zımba ve dişi kalıplar endüstriyel uygulamalarda genellikle AISI 4140 ve EN C45 (Ck 45) kütük malzemelerden talaşlı imalat yöntemiyle elde edilmektedir. Bu kalıpların imalatında yerel ve farklı imalat yöntemlerinin uygulanması dışa bağımlılık ve ekonomiklik anlamında önem kazanmaktadır. Bu çalışmada amaç, döküm yöntemiyle manganlı çelikten “V” bükmede kullanılan zımba ve dişi kalıplarının imal edilerek elde edilen yeni kalıpların mevcut kalıplarla işlenebilirlik ve yüzey pürüzlülüğü yönüyle karşılaştırılmasıdır. Çalışmada hem AISI 4140 hem de manganlı çelikten deney numuneleri farklı kesme parametrelerinde (kesme hızı, ilerleme, talaş derinliği) işlenerek, talaş morfolojisi, kesici takım uç aşınması ve yüzey pürüzlülüğü yönünden analiz edilerek mukayese edilmiştir. Çalışma sonunda yerelde bulunan dökümhanelerde üretilebilen ve yaygın olarak bulunabilen manganlı çelikten üretilen zımba ve dişi kalıpların mevcut AISI4140 çelikten talaşlı imalat yöntemiyle üretilen kalıplara göre işlenebilirlik yönünden de alternatif olduğu sonucuna varılmıştır.

🔖

Cite This Article

ADIYAMAN, O. (2022). Investigation of Press Brake Punches and Dies Produced by Casting Method and From Manganese Steel Material in Terms of Machinability. International Journal of Innovative Engineering Applications, Cilt: 6 - Sayı: 2, 276–285. https://ajindex.com/articles/860010

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (8)

  1. Basmaci, G., & Sayin, L. (2019). Experimental Investigation of the Springback Amount of Copper Sheet Plates Forming By “V” Bending Method. Uluslararası Teknolojik Bilimler Dergisi, 11(3), 147-154.
  2. Ozek, C. & Akkelek, H. (2021). Investigation of Deep Drawability of Rectangular Shaped Cups in Deep Drawing Dies. International Journal of Innovative Engineering Applications, 5(2), 187-194. DOI: 10.46460/ijiea.1006144 Kam, M. (2016). Experimental analyses of the Dynamic Behaviors of Cryogenically processed Shafts, PhD Thesis, Düzce University, Institute of Sciences, Mechanical Engineering, Düzce, Turkey. Uzkut, M., & Özdemir, İ. (2001). Investigation of the effect of changing heating speeds applied to different steels on mechanical properties. Dokuz Eylül University Engineering Faculty Journal of Science and Engineering, 3(3), 65-74.
  3. Avner, S.H., (1986).
  4. Introduction to Physical Metallurgy, McGraw Hill Book Company, 2.ed., New York, 315-336
  5. Oliveira, F., Hernandez, L., Berrios, J.A., Villalobos, C., Pertuz, A. and Cabrera, E.S.P., 2000, Corrosion-fatigue properties of a 4340 steel coated with Commonoy 88 alloy, applied by HVOF thermal spray, Surface and Coatings Technology, 140(2), 128-135.
  6. Charre, M. D., (2004). Microstructure of steel and cast irons, (Trans. J.H. Davidson), Springer-Verlag Berlin Heidelberg New York, p.417. Buytoz, S., (2004). Investigation of mechanical behaviors of AISI 4340 steel after surface modification processes with nitruration and GTA welding method, PhD Thesis, Fırat Univ. Institute of Sciences, Elazığ, p.190. Kesti, E., (2009). Investigation of the effects of C-4140 steel on the temperament of environment of microstructure and mechanical properties, PhD Thesis, Seljuk University Institute of Sciences, Konya. Tüfenk E., (2012). Investigation of Austenitic Manganese Steels with Different Chemical Compositions after Heat treatment, Master Degree Thesis, Ondokuz Mayıs University Institute of Sciences, Samsun Subramanyam, D.K., (2005). Austenitic Manganese Steels. ASM Handbook, Properties and Selection: Irons, Steels, and High Performance Alloys, ASM Int., the United States of America, Vol. 01, 1274-1302. Nejat S., (1995). High manganese austenitic steels and their sources. Journal of Metal and Source, 66, 36-41.
  7. Duflou, J., R., Vancza, J., Aerens, R. (2005). Computer Aided Process Planning for Sheet Metal Bending: A State of the Art, Computers in Industry, 56, 747–771.
  8. De Vin, L. J. (1994). Computer aided process planning for the bendin