Journals / European Mechanical Science / 2022 / Cilt: 6 - Sayı: 4

Investigation of weld defects and mechanical properties of dissimilar friction stir spot welded dual phase (DP600) steel and aluminum alloy (AA 7075-T6) plates

Pages
233–240
Publication Date
2022-12-20
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

In addition, when scanning electron microscope images were examined, it was determined that the cracks observed in the samples and the porosity both increased with increasing tool rotational speed.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:DP600 steel and AA7075-T6 aluminium alloy plates were joined using the friction stir spot welding process.
📊
Key Findings & Data:The highest lap shear tensile load was obtained from the samples joined at a rotational speed of 1040 rpm (6.5 kN).
💡
Conclusion & Impact:In addition, when scanning electron microscope images were examined, it was determined that the cracks observed in the samples and the porosity both increased with increasing tool rotational speed.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Dissimilar welding · İntermetallic compounds · mechanical properties

Abstract

DP600 steel and AA7075-T6 aluminium alloy plates were joined using the friction stir spot welding process. The effects of different tool rotational speeds on the mechanical properties, intermetallic compound formation and interface microstructure of welded joints were investigated. The highest lap shear tensile load was obtained from the samples joined at a rotational speed of 1040 rpm (6.5 kN). It was determined that the tensile load of the welded joint decreased with increasing tool rotational speed. XRD analysis performed on broken surfaces, the intermetallic phase was determined to be Al13Fe4. As a result of Vickers microhardness tests, the samples joined at 1320 rpm and 1500 rpm, in the structure of which intermetallic compounds were determined by XRD analysis, displayed higher hardness values. In addition, when scanning electron microscope images were examined, it was determined that the cracks observed in the samples and the porosity both increased with increasing tool rotational speed.

🔖

Cite This Article

ÇAKAN, A., UĞURLU, M. (2022). Investigation of weld defects and mechanical properties of dissimilar friction stir spot welded dual phase (DP600) steel and aluminum alloy (AA 7075-T6) plates. European Mechanical Science, Cilt: 6 - Sayı: 4, 233–240. https://ajindex.com/articles/859315

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Ogura, T., Saito, Y., Nishida, T., Nishida, H., Yoshida, T., Omichi, N., Fujimoto, M., Hirose, A., (2012). Partitioning evaluation of mechanical properties and the interfacial microstructure in a friction stir welded aluminum alloy/stainless steel lap joint, Scripta Materialia. 66(8): 531–534.
  2. Ogura, T., Nishida, T., Tanaka, Y., Nishida, H., Yoshikawa, S., Fujimoto, M., Hirose, A., (2013). Microscale evaluation of mechanical properties of friction stir welded A6061 aluminium alloy / 304 stainless steel dissimilar lap joint, Science and Technology of Welding and Joining. 18(2): 108–113.
  3. Doruk, E., Pakdil, M., Çam, G., Durgun, İ., Kumru, U. C., (2016). Resistance spot welding applications in automotive industry. Engineer and Machinery, 57(673): 48-53
  4. Zhang, W., Sun, D., Han, L., Gao, W., Qiu, X., (2011). Characterization of intermetallic compounds in dissimilar material resistance spot welded joint of high strength steel and aluminum alloy. The Iron and Steel Institute of Japan. 51(11): 1870–1877.
  5. Cakan, A., Atmaca, H., Ugurlu, M., (2018). Analysis and joining of Al – Cu plates using friction stir welding technique. European Mechanical Science. 2(1): 1–8.
  6. Cakan, A., Ugurlu, M., Kaygusuz, E., (2019). Effect of weld parameters on the microstructure and mechanical properties of dissimilar friction stir joints between pure copper and the aluminum alloy AA7075-T6. Materials Testing. 61(2): 142–148.
  7. Ugurlu, M., Cakan, A., (2019). The effect of tool rotation speed on mechanical properties of friction stir spot welded ( FSSW ) AA7075-T6 aluminium alloy. European Mechanical Science. 3: 97–101.
  8. Çam, G., Javaheri, V., Heidarzadeh, A. (2022). Advances in FSW and FSSW of dissimilar Al-alloy plates. Journal of Adhesion Science and Technology, 1-33.
  9. Çam, G., (2011). Friction stir welded structural materials: beyond Al-alloys. International Materials Reviews, 56(1): 1-48. https://doi: 10.1179/095066010X12777205875750 10
  10. Çam, G., İpekoğlu, G., (2017). Recent developments in joining of aluminum alloys. The International Journal of Advanced Manufacturing Technology, 91(5): 1851-1866. https://doi.org/10.1007/s00170-016-9861-0. 11 [11]