Journals / Turkish Journal of Geosciences / 2022 / Cilt: 3 - Sayı: 1

Investigation of the effects of different flight parameters on the accuracy of DEM generated using UAV systems

Pages
22–29
Publication Date
2022-06-28
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

It is concluded that the Orthomosaics produced using 450 angle and DEMs with 600 angle has higher accuracy than the others.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Unmanned Aerial Vehicles (UAVs), can be controlled automatically or with the help of a remote control system, provide high spatial and temporal resolution images in addition to its advantages in terms of cost and time.
📊
Key Findings & Data:Due to these features, UAV’s have been widely used in studies such as map production, 3D modeling and volume calculation in recent years.
💡
Conclusion & Impact:It is concluded that the Orthomosaics produced using 450 angle and DEMs with 600 angle has higher accuracy than the others.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:photogrammetry · UAV · ortophoto

Abstract

Unmanned Aerial Vehicles (UAVs), can be controlled automatically or with the help of a remote control system, provide high spatial and temporal resolution images in addition to its advantages in terms of cost and time. Due to these features, UAV’s have been widely used in studies such as map production, 3D modeling and volume calculation in recent years. In this study, it is aimed to investigate the effects of different flight parameters on the accuracy of Orthomosaic and DEM produced with UAV Systems. In addition, the rolling shutter effect and the use of pre-calibrated and automatic camera calibration parameters were also tested. For this purpose, a total of seven UAV flights were carried out at different heights, overlap ratios, angles and grids at a mining area located within the borders of Aksaray province. Agisoft MetaShape and Pix4D Mapper, which are widely used commercial software, were used to process the UAV images. In this study, 27 points were established and 3D coordinates of these points were measured using GNSS technique. 15 of these points were used as reference points and the remaining 12 points were used as check points. Accuracy analysis was performed by comparing the produced Orthomosaics and DEMs with the check points in the study area. CloudCompare and ArcGIS software were used in the comparison of the products as a result of the evaluation of the images. It is concluded that the Orthomosaics produced using 450 angle and DEMs with 600 angle has higher accuracy than the others. Point clouds and DEMs’ produced using automatic and pre-calibrated camera calibration parameters show that the pre-calibrated images provide higher accuracy. Also, it is seen that when the rolling shutter effect is modeled, the horizontal and vertical accuracy is increased in all three flights with different flight parameters in this study.

🔖

Cite This Article

BULUT, E., YILMAZTÜRK, F. (2022). Investigation of the effects of different flight parameters on the accuracy of DEM generated using UAV systems. Turkish Journal of Geosciences, Cilt: 3 - Sayı: 1, 22–29. https://ajindex.com/articles/808852

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (8)

  1. Ait-Aider, O., Andreff, N., Lavest, J.M., & Martinet, P. (2006). Simultaneous object pose and velocity computation using a single view from a rolling shutter camera. In European Conference on Computer Vision, Springer, Berlin, Heidelberg. Akay S.S., & Ozcan O. (2017). Volumetric Comparison of Uav-Based Point Clouds Generated from Various Softwares. International Symposium on GIS Applications in Geography and Geosciences, Çanakkale, Turkey. Akay, S. S., Özcan, O., Şanlı, F. B., Bayram, B., & Görüm, T. (2019). İHA görüntülerinden üretilen verilerin doğruluk değerlendirmesi, 10. Türkiye Ulusal Fotogrametri ve Uzaktan Algılama Birliği Teknik Sempozyumu, TUFUAB 2019, 106-110.
  2. Akay, S.S., Ozcan, O., Şanlı, F.B., Bayram, B., & Görüm, T. (2021). Assessing the spatial accuracy of UAV-derived products based on variation of flight altitudes. Turkish Journal of Engineering, 5(1), 35-40.
  3. Atak, H. (2018). Producing orthophoto maps using unmanned air vehicles and accuracy analysis (MSc thesis). Gebze Technical University, Kocaeli, Turkey (in Turkish). Çömert, R., Avdan, U., & Şenkal, E. (2012). İnsansız Hava Araçlarının Kullanım Alanları ve Gelecekteki Beklentileri. IV. Uzaktan Algılama ve Coğrafi Bilgi Sistemleri Sempozyumu, Zonguldak. Coşkun, E. (2020). Mapping production using unmanned aerial vehicles: Case of Altinordu district of Ordu (MSc thesis). Çukurova University, Adana, Turkey (in Turkish). Döner, F., Özdemir, S., & Ceylan, M. (2014). İnsansız Hava Aracı Sistemlerinin Veri Toplama Ve Haritalama Çalışmalarında Kullanımı. Uzaktan Algılama–Cbs Sempozyumu, 14-17.
  4. Eltner, A., Kaiser, A., Abellan, A., & Schindewolf, M. (2017). Time Lapse Structure-From-Motion Photogrammetry for Continuous Geomorphic Monitoring. Earth Surface Processes and Landforms, 42(14), 2240–2253.
  5. Erdoğan, M., & Toz, G. (2009). Sayısal Yükseklik Modeli (Sym) Doğruluk ve Üretim Maliyetleri. Türkiye Ulusal Fotogrametri ve Uzaktan Algılama Birliği Sempozyumu TUFUAB 2009.
  6. Gündoğdu, K.S. (2003). Sayısal Yükseklik Modellerinin Arazi Boy Kesitlerinin Çıkarılmasında Kullanımı, Uludağ Üniversitesi Ziraat Fakültesi Dergisi, 17, 149-157.
  7. Karabörk, H., Makineci, H.B., Orhan, O. & Karakus, P. (2021). Accuracy assessment of DEMs derived from multiple SAR data using the InSAR technique. Arabian Journal for Science and Engineering, 46(6), 5755-5765.
  8. Kılınç-Kazar, G., Karabörk, H., & Makineci, H.B. (2022). Evaluation of Test Field-based Calibration and Self-calibration Models of UAV Integrated Compact Cameras. J