Journals / Konya Mühendislik Bilimleri Dergisi / 2013 / Cilt: 1 - Sayı: 3

A New 3D Scanner for Digitizing Discontinuity Surface Roughness

SÜREKSİZLİK YÜZEY PÜRÜZLÜLÜĞÜNÜ SAYISALLAŞTIRMAK İÇİN YENİ BİR ÜÇ BOYUTLU TARAMA CİHAZI

Pages
45–58
Publication Date
2013-09-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

With this data the roughness can be analyzed.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, a new 3-dimensional scanner is developed to digitize the roughness of the discontinuity surfaces of rock mass.
📊
Key Findings & Data:By using this device, a 3D topography of the surface can be obtained.
💡
Conclusion & Impact:With this data the roughness can be analyzed.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Kaya kütlesi · Süreksizlik · Pürüzlülük

Abstract

In this study, a new 3-dimensional scanner is developed to digitize the roughness of the discontinuity surfaces of rock mass. The device uses a camera and a laser which projects a line on the surface with right angle. The camera is placed diagonally to the surface so the profile of the surface can be recorded and can be digitized by direct linear transformation algorithm. The system consists of three main parts: hardware, electronic card and software. In the mechanical setup, the laser and the camera are scrolled along a rail by a worm gear which is driven by a step motor. Electronic card controls the laser and the step motor according to the commands from the software. Camera calibration, scanning, image analysis, detection of the laser stripe and direct linear transformation calculations are made by using the developed software. By using this device, a 3D topography of the surface can be obtained. With this data the roughness can be analyzed.

Özet

Bu çalışmada kaya kütlesinde bulunan süreksizliklere ait pürüzlülüklerin sayısallaştırılması için yeni bir üç boyutlu tarayıcı cihaz geliştirilmiştir. Cihazın çalışma prensibi, taranacak yüzeye dikey olarak çizgi lazer yansıtılması ve farklı bir açıdan görüntü alınarak, direk lineer transformasyon yöntemiyle profilin elde edilmesi esasına dayanmaktadır. Sistem üç ana parçadan, mekanik, elektronik ve yazılımdan oluşmaktadır. Mekanik kısım, üzerinde çizgi lazer ve kamera bulunan bir taşıyıcı ve bu taşıyıcının üzerinde hareket edebildiği kızak sisteminden oluşmaktadır. Kızak üzerinde taşıyıcının hareketini sağlayan sonsuz mil ve buna hareketi veren bir adım motor vardır. Elektronik kart, yazılımdan gelen komutlara göre, adım motoru ve lazeri idare etmektedir. Yazılım aracılığıyla kamera kalibrasyonu, tarama, görüntü iyileştirme, lazer çizgisinin tespiti ve direkt lineer transformasyon ile üç boyutlu yüzeyin elde edilmesi işlemleri gerçekleştirilmektedir. Bu cihaz kullanılarak, temassız olarak, istenilen yüzeyin üç boyutlu topoğrafyası elde edilerek, analiz için gerekli veriler elde edilmektedir.

🔖

Cite This Article

ÖNSEL, İ., ÖZTÜRK, C. (2013). A New 3D Scanner for Digitizing Discontinuity Surface Roughness. Konya Mühendislik Bilimleri Dergisi, Cilt: 1 - Sayı: 3, 45–58. https://ajindex.com/articles/786931

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Barton, N., Choubey, V., 1977, “The Shear Strength Of Rock Joints In Theory And Practice”, Rock mechanics, Cilt 10, Sayı 1-2, sayfa 1-54.
  2. Chae, B. G., Ichikawa, Y., Jeong, G. C., Seo, Y. S. and Kim, B. C., 2004, “Roughness Measurement of Rock Discontinuities Using a Confocal Laser Scanning Microscope and the Fourier Spectral Analysis”, Engineering Geology, 72, 3-4, 181-199.
  3. Chen, R. H., Lee, C. W. and Chen, C. S., 2001, “Evaluation of Transport of Radioactive Contaminant in Fractured Rock”, Environmental Geology, 41, 3-4, 440-450.
  4. Develi, K., Babadagli, T. and Comlekci, C., 2001, “A New Computer-Controlled Surface-Scanning Device for Measurement of Fracture Surface Roughness”, Computers & Geosciences, 27, 3, 265-277.
  5. Fardin, N., Feng, Q. and Stephansson, O., 2004, “Application of a New in Situ 3d Laser Scanner to Study the Scale Effect on the Rock Joint Surface Roughness”, International Journal of Rock Mechanics and Mining Sciences, 41, 2, 329-335.
  6. Fecker, E., Rengers, N., “Measurements of large scale roughness of rock planes by means of profilograph and geological compass”, Proceedings Symposium Rock Fracture, Nancy, 1-18, 1971.
  7. Feng, Q., Fardin, N., Jing, L. and Stephansson, O., 2003, “A New Method for in-Situ Non-Contact Roughness Measurement of Large Rock Fracture Surfaces”, Rock Mechanics and Rock Engineering, 36, 1, 3-25.
  8. Goodman, R. E., 1993, Engineering Geology: Rock in Engineering Construction, J. Wiley, New York; Chichester. Grasselli, G., 2006, “Manuel Rocha Medal Recipient - Shear Strength of Rock Joints Based on Quantified Surface Description”, Rock Mechanics and Rock Engineering, 39, 4, 295-314.
  9. Grasselli, G. and Egger, P., 2003, “Constitutive Law for the Shear Strength of Rock Joints Based on ThreeDimensional Surface Parameters”, International Journal of Rock Mechanics and Mining Sciences, 40, 1, 25-40.
  10. Grasselli, G., Wirth, J. and Egger, P., 2002, “Quantitative Three-Dimensional Description of a Rough Surface and Parameter Evolution with Shearing”, International Journal of Rock Mechanics and Mining Sciences, 39, 6, 789800. Hamdi, E. and du Mouza, J., 2005, “A Methodology for Rock Mass Characterisation and Classification to Improve Blast Results”, International Journal of Rock Mechanics and Mining Sciences, 42, 2, 177-194.
  11. Johansson, F., 2009, Shear Strength of Unfilled and Rough Rock Joints in Sliding Stability Analyses of Concrete Dams, Doktora Tezi, Royal Institute of Technology, Stockholm. Kwon, Y.H., Camera Calibration, http://www.kwo