Journals / International Journal of Engineering Technologies / 2019 / Cilt: 5 - Sayı: 1

Optimization of Process Parameters of the Plate Heat Exchanger

Pages
24–30
Publication Date
2019-03-29
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results show that air flow rate is the most significant factor among the three factors that influences the thermal effectiveness.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The aim of this study is to determine the importance of the operation factors affecting the recovery performance in air-to-air heat recovery application where heat exchanger is used.
📊
Key Findings & Data:Thermal effectiveness has been determined as performance characteristic.
💡
Conclusion & Impact:The results show that air flow rate is the most significant factor among the three factors that influences the thermal effectiveness.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Air to air heat recovery · Plate heat exchanger · Effectiveness

Abstract

The aim of this study is to determine the importance of the operation factors affecting the recovery performance in air-to-air heat recovery application where heat exchanger is used. The Taguchi experimental design method has been applied to show the effects of the factors and obtain the optimum process parameter combination. Thermal effectiveness has been determined as performance characteristic. Experiments have been carried out at varying air flow rate, fresh and exhaust air inlet temperatures. Taguchi's L9(33) standard orthogonal array has been chosen as an experimental plan. The significance level of the control factors has been obtained by using analysis of variance (ANOVA). F test has been performed to determine whether the study is statistically significant. The results show that air flow rate is the most significant factor among the three factors that influences the thermal effectiveness. The results prove that Taguchi method is an easily applicable optimization tool for heat recovery systems.

🔖

Cite This Article

KOCABAŞ, C., SAVAŞ, A. F. (2019). Optimization of Process Parameters of the Plate Heat Exchanger. International Journal of Engineering Technologies, Cilt: 5 - Sayı: 1, 24–30. https://ajindex.com/articles/766919

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Coşkun S., Motorcu A. R., Yamankaradeniz N., Pulat E, “Evaluation of control parameters’ effects on system performance with Taguchi method in waste heat recovery application using mechanical heat pump”, Refrigeration, vol. 35, pp. 795-809, 2012. Yun J. and Lee K, “Influence of design parameters on the heat transfer and flow friction characteristics of the heat exchanger with slit fins”, International Journal of Heat and Mass Transfer, vol. 43, pp. 2529-2539, 2000.
  2. Şahin B, Yakut K., Kotcioglu I., Çelik C., “Optimum design parameters of a heat exchanger”, Applied Energy, vol. 82, pp. 90–106, 2005.
  3. Yakut K., Alemdaroglu N., Şahin B., Çelik C., “Optimum design-parameters of a heat exchanger having hexagonal fins”, Applied Energy, vol. 83, pp. 82–98, 2006.
  4. Qi Z., Chen J., Chen Z., “Parametric study on the performance of a heat exchanger with corrugated louvered fins”, Applied Thermal Engineering, vol. 27, pp. 539–544, 2007. Şahin B. and Demir A., “Performance analysis of a heat exchanger having perforated square fins”, Applied Thermal Engineering, vol. 28, pp. 621-632, 2008. Turgut E.,Çakmak G., Yıldız C., “Optimization of the concentric heat exchanger with injector turbulators by Taguchi method”, Energy Conversion and Management, 53, 268–275, 2012.
  5. Hsieh C.T., Jang, J.Y., “Parametric study and optimization of louver finned-tube heat exchangers by Taguchi method”, Applied Thermal Engineering, vol. 42, pp. 101-110, 2012.
  6. Kotcioglu I, Cansiz A., Khalaji M. N., “Experimental investigation for optimization of design parameters in a rectangular duct with plate-fins heat exchanger by Taguchi Method”, Applied Thermal Engineering, vol. 50, pp. 604-613, 2013.
  7. Junqi D., Yi Z., Gengtian L., Weiwu X., “Experimental study of wavy fin aluminium plate fin heat exchanger”, Experimental Heat Transfer, vol. 26, pp. 384–396, 2013.
  8. Jamshidi N., Farhadi M., GanjiD.D., Sedighi K., “Experimental analysis of heat transfer enhancement in shell and helical tube heat exchangers”, Applied Thermal Engineering, vol. 51, pp. 644-652, 2013.
  9. Tingting Du, Wenjing Du, Kai Che, Lin Cheng, “Parametric optimization of overlapped helical baffled heat exchangers by Taguchi method”, Applied Thermal Engineering, vol. 85, pp. 334-339, 2015.
  10. Bilen K., Yapıcı S., Çelik C., ”A Taguchi approach for investigation of heat transfer from a surface equipped with rectangular blocks”, Energy Conversion and Management, vol. 42, pp. 951-961, 2001. Kocabaş C., “Experimental analysis of waste heat recovery performanc