SavedAdd your journal

Journals / International Journal of Automotive Science and Technology / 2022 / Cilt: 6 - Sayı: 2

Evaluation of the effect of the novolac resin ratio on the high temperature performance of the brake pads

Gülşah AKINCIOĞLU
Pages
196–201
Publication Date
2022-06-30
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

With the increase in the novolac res-in ratio, the hardness, density, and thermal conductivity of the brake pads have in-creased.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The resin is a widely used binder in the brake pads.
📊
Key Findings & Data:Determining the optimum, resin ratio is important for the brake pad to show the best wear and braking performance.
💡
Conclusion & Impact:With the increase in the novolac res-in ratio, the hardness, density, and thermal conductivity of the brake pads have in-creased.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Brake Pad · Novolac Resin · High Temperature

Abstract

The resin is a widely used binder in the brake pads. Determining the optimum, resin ratio is important for the brake pad to show the best wear and braking performance. In this article, the impression of the novolac resin ratio (15% and 30%) on the perfor-mance of the brake pads at high temperatures was studied. Friction experiments of the brake pads were performed according to ASTM G99–95a test standard in Pin-on disc test device at 350 °C. The average friction coefficients obtained in the friction tests of 15% and 30% novolac resin samples at 500 rpm rotation speed, 350 C temperature, and 10 N load were 0.151 and 0.308, respectively. With the increase in the novolac res-in ratio, the hardness, density, and thermal conductivity of the brake pads have in-creased.

🔖

Cite This Article

AKINCIOĞLU, G. (2022). Evaluation of the effect of the novolac resin ratio on the high temperature performance of the brake pads. International Journal of Automotive Science and Technology, Cilt: 6 - Sayı: 2, 196–201. https://ajindex.com/articles/717098

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (13)

  1. Y.C. Kim, M.H. Cho, S.J. Kim, H. Jang, The effect of phenolic resin, potassium titanate, and CNSL on the tribological properties of brake friction materials, Wear, 264 (2008) 204-210
  2. G. Akıncıoğlu, S. Akıncıoğlu, H. Öktem, İ. Uygur, Wear response of non-asbestos brake pad composites reinforced with walnut shell dust, Journal of the Australian Ceramic Society, 56 (2020) 1061-1072
  3. H. Öktem, S. Akıncıoğlu, İ. Uygur, G. Akıncıoğlu, A novel study of hybrid brake pad composites: new formulation, tribological behaviour and characterisation of microstructure, Plastics, Rubber and Composites, (2021) 1-13
  4. S. Koch, E. Köppen, N. Gräbner, U. von Wagner, On the influence of multiple equilibrium positions on brake noise, Facta Universitatis, Series: Mechanical Engineering, (2021)
  5. G. Akıncıoğlu, İ. Uygur, H. Öktem, S. Akıncıoğlu, Bor oksit tozunun fren balatalarının tribolojik özelliklerine etkisi, Sakarya University Journal of Science, 22 (2018) 755-760
  6. P. Gurunath, J. Bijwe, Friction and wear studies on brake-pad materials based on newly developed resin, Wear, 263 (2007) 1212-1219
  7. G. Akıncıoğlu, S. Akıncıoğlu, H. Öktem, İ. Uygur, Evaluation of the physical properties of hazelnut shell dust-added brake pad samples treated with cryogenic process, Politeknik Dergisi, 22 (2019) 591-596
  8. R. Ertan, N. Yavuz, An experimental study on the effects of manufacturing parameters on the tribological properties of brake lining materials, Wear, 268 (2010) 1524-1532
  9. C. Menapace, M. Leonardi, M. Secchi, A. Bonfanti, S. Gialanella, G. Straffelini, Thermal behavior of a phenolic resin for brake pad manufacturing, Journal of Thermal Analysis and Calorimetry, 137 (2019) 759-766
  10. H.Q. Wang, X.Y. Wu, T.S. Li, X.J. Liu, P.H. Cong, Effect of the matrix resin structure on the mechanical properties and braking performance of organic brake pads, Journal of applied polymer science, 126 (2012) 1746-1753
  11. S.J. Kim, H. Jang, Friction and wear of friction materials containing two different phenolic resins reinforced with aramid pulp, Tribology international, 33 (2000) 477-484
  12. M. Lagel, L. Hai, A. Pizzi, M. Basso, L. Delmotte, S. Abdalla, A. Zahed, F. Al-Marzouki, Automotive brake pads made with a bioresin matrix, Industrial Crops and Products, 85 (2016) 372-381
  13. Y. Wu, M. Zeng, Q. Xu, S. Hou, H. Jin, L.J.T.I. Fan, Effects of glass-to-rubber transition of thermosetting resin matrix on the friction and wear properties of friction materials,