SavedAdd your journal

Journals / Uludağ Üniversitesi Mühendislik Fakültesi Dergisi / 2013 / Cilt: 18 - Sayı: 1

Heat Transfer Enhancement in Turbulent Flows by Blocked Surfaces

Türbülanslı Akışta Isı Transferinin Bloklu Yüzeyler ile Arttırılması

Onur YEMENİCİ
Z. Abidin FIRATOĞLU
Pages
61–67
Publication Date
2013-04-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results showed that the presence of the blocks increased the heat transfer and the enhancement rose with block heights

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, the heat transfer analyses over flat and blocked surfaces were carried out in turbulent flow under the influence of the block height.
📊
Key Findings & Data:The average Stanton numbers for block heights of 15 and 25 mm were higher than those of flat surface by %38 and %84, respectively.
💡
Conclusion & Impact:The results showed that the presence of the blocks increased the heat transfer and the enhancement rose with block heights
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Bloklu yüzey · Türbülanslı akış · Isı transferi artırımı

Abstract

In this study, the heat transfer analyses over flat and blocked surfaces were carried out in turbulent flow under the influence of the block height. A constant-temperature hot wire anemometer was used to the velocity and turbulent intensity measurements, while temperature values were measured by copper-constantan thermocouples. The average Stanton numbers for block heights of 15 and 25 mm were higher than those of flat surface by %38 and %84, respectively. The results showed that the presence of the blocks increased the heat transfer and the enhancement rose with block heights

Özet

Bu çalışmada, düz ve bloklu yüzeyler üzerinde türbülanslı akış için ısı transferi analizi blok yüksekliğine bağlı olarak yapılmıştır. Hız ve türbülans yoğunlukları ölçümlerinde sabit sıcaklıklı bir kızgın tel anemometresi kullanılırken, sıcaklık değerleri termal çiftler ile ölçülmüştür. 15 ve 25 mm blok yüksekliklerine sahip bloklu yüzey ortalama Stanton sayılarının, düz yüzey değerlerinden sırasıyla %38 ve %84 daha fazla olduğu tespit edilmiştir. Bu sonuçlar, blokların varlığının ısı transferini önemli derecede arttırdığını ve ısı transferinin blok yüksekliği ile arttığını göstermektedir

🔖

Cite This Article

YEMENİCİ, O., FIRATOĞLU, Z. A. (2013). Heat Transfer Enhancement in Turbulent Flows by Blocked Surfaces. Uludağ Üniversitesi Mühendislik Fakültesi Dergisi, Cilt: 18 - Sayı: 1, 61–67. https://ajindex.com/articles/708864

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Bilen, K. ve Yapıcı, S. (2001) Heat transfer form a surface fitted with rectangular blocks at different orientation angle, Heat and Mass transfer, 38, 649-655.
  2. Chen, Y.M. ve Wang, K.C. (1998) Experimental study on the forced convective flow in a channel with heated blocks in tandem, Experimental Thermal and Fluid Science, 16, 286- 298. Kays, W.M. ve Crawford, M.E. (1993)
  3. Convective heat and mass transfer, New York: McGraw Hill. Kim, S.H. ve Anand, N.K. (1994) Turbulent heat transfer between a series of parallel plates with surface-mounted discrete heat sources, Journal of Heat Transfer, 116, 577-587.
  4. Kline, S.J. ve McClintock, F.A. (1953) Describing uncertainties in single sample experiments, Mech. Eng., 75, 3-8.
  5. Korichi, A. ve Oufer, L. (2006) Heat transfer enhancement in oscillatory flow in channel with periodically upper and lower walls mounted obstacles, International Journal of Heat and Fluid Flow, 52, 1138-1148.
  6. Lee, C.K., Abdel-Moneim, S.A. (2001) Computational analysis of heat transfer in turbulent flow past a horizontal surface with two-dimensional ribs, International Communication Heat and Mass Transfer, 28, 161-170.
  7. Leung, C.W., Kang H.J. ve Probert, S.D. (1997) Horizontal simulated printed-circuit board assembly in fully-developed laminar-flow convection, Applied Energy, 56, 71-91.
  8. Mohammed, M.M. (2006) Air cooling characteristics of a uniform square modules array for electronic device heat sink, Applied Thermal Engineering, 26, 486–493.
  9. Morris, G.K. ve Garimella, S.V. (1996) Thermal wake downstream of a three-dimensional obstacle, Experimental Thermal and Fluid Science. 12, 65-74.
  10. Naik, S., Probert, S.D. ve Bryden, I.G. (1999) Heat transfer characteristics of shrouded longitudinal ribs in turbulent forced convection, International Journal of Heat and Fluid Flow, 20, 374-384.
  11. Perng, S-W ve Wu, H-W. (2008) Numerical investigation of mixed convective heat transfer for unsteady turbulent flow over heated blocks in a horizontal channel, International Journal of Thermal Sciences, 47, 620-632.
  12. Ryu, D.N., Choi, D.H. ve Patel, V.C. (2007) Analysis of turbulent flow in channels roughened by two-dimensional ribs and three-dimensional blocks, Part II: Heat transfer, International Journal of Heat and Fluid Flow, 28, 1112-1124.
  13. Sara, O.N., Pekdemir T., Yapıcı S. ve Yılmaz M. (2001) Enhancement of heat transfer from a flat surface in a channel flow by attachment of rectangular blocks, International Journal of Energy Research, 25, 563-576.
  14. Tsay, Y.-L. ve Chen