Journals / Teknik Dergi / 2022 / Cilt: 33 - Sayı: 6

An Experimental Investigation on the Fill Properties of Industrial By-Products Generated in Turkey

Türkiye’de Çıkan Endüstriyel Yan Ürünlerin Dolgu Özellikleri Üzerine Deneysel Bir İnceleme

Pages
12789–12815
Publication Date
2022-11-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The results of the leachate analysis point toward the need for further analysis of the mixture for the environmental effects.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Steel slag and fly ash are particulate industrial by-products generated in steel plants and power plants, respectively.
📊
Key Findings & Data:In this study, the properties of steel slag, fly ash and a steel slag-fly ash mixture that contain 20% fly ash (by weight) were investigated for their possible use as fill material.
💡
Conclusion & Impact:The results of the leachate analysis point toward the need for further analysis of the mixture for the environmental effects.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:BOF çelik cürufu · uçucu kül · kompaksiyon

Abstract

Steel slag and fly ash are particulate industrial by-products generated in steel plants and power plants, respectively. In this study, the properties of steel slag, fly ash and a steel slag-fly ash mixture that contain 20% fly ash (by weight) were investigated for their possible use as fill material. Fly ash and steel slag were characterized through specific gravity, sieve, hydrometer and Atterberg limits experiments. Compaction behavior of the industrial by-products and their mixture were evaluated through standard Proctor compaction, and their hydraulic conductivity were determined through falling-head permeability experiments. The shear strength parameters of the industrial by-products and their mixtures, prepared at 100% Proctor compaction, were evaluated based on direct shear experiments. pH and electrical resistivity measurements were taken, and leachate analysis were performed on fly ash and steel slag samples to determine the possible environmental risks that can arise from their use. The maximum dry unit weight values recorded for the 80% steel slag - 20% fly ash mixture was higher, on the other hand, the optimum moisture content of the mixture was lower compared to that of steel slag sample. Based on direct shear experiments, the end-of-test friction angles are 40.1o and 28.9o for steel slag and fly ash, respectively. The end-of-test friction angle for the 80% steel slag-20% fly ash mixture is 37.8o. The peak shear strength of the mixture is close to that of steel slag and comparable to the higher end of the range obtained for natural sands that are used as fill material. The pH and electrical resistivity measurements indicate that these by-products may possess corrosive nature. The results of the leachate analysis point toward the need for further analysis of the mixture for the environmental effects.

Özet

Çelik cürufu ve uçucu kül sırasıyla çelik üretim tesislerinde ve termik santrallerde katı partiküller halinde ortaya çıkan endüstriyel yan ürünlerdir. Bu çalışmada dolgu uygulamalarında kullanılabilmeleri için, uçucu kül ve ağırlıkça %20 uçucu kül içeren çelik cürufu-uçucu kül karışımının özellikleri incelenmiştir. Uçucu kül ve çelik cürufu, özgül ağırlık, elek, hidrometre ve Atterberg limitleri deneyleriyle karakterize edilmiştir. Kompaksiyon davranışı standart Proktor deneyleriyle belirlenen yan ürünlerin ve karışımın hidrolik iletkenlik katsayıları düşen seviyeli permeabilite deneyleriyle belirlenmiştir. Yan ürünlerin ve karışımın kayma dayanımı parametreleri %100 Standart Proktor sıkılığında hazırlanan numuneler üzerinde yapılan kesme kutusu deneylerinin sonuçlarına göre değerlendirilmiştir. pH ve elektrik iletkenliği ölçümleri ve sızıntı suyu analizleri yapılarak malzemelerin kullanımıyla oluşabilecek çevresel risklerin belirlenmesi hedeflenmiştir. Kompaksiyon deneylerinde %80 çelik cürufu-%20 uçucu kül karışımı için elde edilen kuru birim hacim ağırlığı çelik cürufuna göre daha yüksek, karışma ait optimum su muhtevası çelik cürufuna göre daha düşüktür. Kesme kutusu deney sonuçlarına göre, deney-sonu sürtünme açısı, çelik cürufu ve uçucu kül için sırasıyla 40.1o ve 28.9o’dir. %80 çelik cürufu-%20 uçucu kül karışımının deney-sonu sürtünme açısı ise 37.8o’dir. Karışımın pik kayma dayanımı çelik cürufu için elde edilene yakın ve dolgu için kullanılan doğal kum malzemeleri için elde edilen değerlerin üst sınırı ile karşılaştırılabilir. pH ve elektrik iletkenliği ölçümleri, kullanılan yan ürünlerin korozif özellikler gösterebileceğine işaret etmektedir. Çelik cürufu ve uçucu kül numuneleri için yapılan sızma suyu analiz sonuçları çevre etkilerinin üretilen karışım için araştırılması gerektiğine işaret etmektedir.

🔖

Cite This Article

YİLDİRİM, İ. Z. (2022). An Experimental Investigation on the Fill Properties of Industrial By-Products Generated in Turkey. Teknik Dergi, Cilt: 33 - Sayı: 6, 12789–12815. https://ajindex.com/articles/703156

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Association of State and Territorial Solid Waste Management Officials (ASTSWMO). 2006
  2. Beneficial Use Survey. Survey Report, ASTSWMO -Beneficial Use Task Force, Washington, D.C., 2007.
  3. Segerstorm, W., Dove, J., Recycled materials in geo-construction: A Review of Potential Benefits and Hazards. Scientific Report, CPGR No 61, Virginia Tech Center for Geotechnical Practice and Research, Virginia Polytechnic Institute and State University, VA, 2010. Environmental Protection Agency (EPA). Methodology for Evaluating Beneficial Uses of Non-Hazardous Industrial Secondary Materials. Technical Report, No. 530-R-16-011, Office of Resource Conservation and Recovery-Office of Land and Emergency Management, Washington, D.C., 2016.
  4. Ahmedzade, P., Sengoz, B., Evaluation of steel slag coarse aggregate in hot mix asphalt concrete. J. Hazard. Mater., 165,1-3, 300-305, 2009.
  5. Shen, D., Wu, C., Du, J., Laboratory investigation of basic oxygen furnace slag for substitution of aggregate in porous asphalt mixture. Constr Build Mater, 23,1, 453-461, 2009.
  6. Wu, S., Xue, Y., Ye, Q., Chen, Y., Utilization of steel slag aggregates for stone mastic asphalt (SMA) mixtures. Build Environ, 42, 7, 2580-2585, 2009.
  7. Ameri, M., Hesami, S., Goli, H., Laboratory evaluation of warm mix asphalt mixtures containing electric arc furnace (EAF) steel slag. Constr Build Mater, 49, 611-617, 2013.
  8. Montgomery, D.G., Wang, G., Instant-chilled steel slag aggregate in concrete-strength related properties. Cem Concr Res, 21, 6, 1083–1091, 1991.
  9. Maslehuddin, M, Sharif, M.A., Shameem, M., Ibrahim, M., Barry, M.S., Comparison of properties of steel slag and crushed limestone aggregates. Constr Build Mater, 17, 2,105-112, 2003.
  10. Manso, J.M., Polanco, J.A., Losanez, M., Gonzales, J.J., Durability of concrete made with EAF slag as aggregate. Cem Concr Compos, 28,6, 528-534, 2006.
  11. Abu-Eishah, S.I., El. Dieb, A.S., Bedir, M.S., Performance of concrete mixtures made with electric arc furnace (EAF) steel slag aggregate produced in the Arabian Gulf region”. Constr Build Mater, 34, 249-256, 2012.
  12. Rondi, L., Bregoli, G., Sorlini, S., Cominoli, L., Collivignarelli, C., Plizzari, G., Concrete with EAF steel slag aggregate: A comprehensive technical and environmental characterization. Compos B Eng, 90, 195-202, 2016.
  13. Conjeaud, M., George, C. M., Sorrentino, F. P., A new steel slag for cement manufacture: mineralogy and hydraulicity. Cem Concr Res, 11, 1, 85–102, 1981.
  14. Tufekci, M., Demirbas, A., Genc, H., Evaluation of steel fur