SavedAdd your journal

Journals / Karadeniz Fen Bilimleri Dergisi / 2019 / Cilt: 9 - Sayı: 2

Investigation of the Surface Properties TaN Based Thin Film Coatings on the CoCrMo Alloy

CoCrMo Alaşımı Üzerine TaN Esaslı İnce Film Kaplamaların Yüzey Özelliklerinin İncelenilmesi

Erkan BAHÇE
Ali Kemal ASLAN
Neşe ÇAKIR
Mehmet Sami GÜLER
Pages
223–237
Publication Date
2019-12-15
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Results showed that as a result of coating process tribological properties of the alloy were improved significantly.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:CoCrMo alloy is widely used as orthopedic implant material thanks to its properties like high impact and fatigue strength.
📊
Key Findings & Data:Results showed that as a result of coating process tribological properties of the alloy were improved significantly.
💡
Conclusion & Impact:It is observed that with increasing number of layer, wear strength, hardness and surface quality of the samples improved.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Biyomalzeme · CoCrMo alaşımı · Kaplama

Abstract

CoCrMo alloy is widely used as orthopedic implant material thanks to its properties like high impact and fatigue strength. This alloy has high corrosion strength but low wear strength. When it is used as an artificial joint implant material it subjects to both wear and corrosion because of the aggressive body fluid in terms of corrosion. Therefore, the surface coating process is applied to CoCrMo alloys to improve the corrosion and wear strength together. In this study, in order to improve the tribological properties of CoCrMo alloy, its surface was multilayer coated via close field unbalanced magnetron sputtering process. Coating architecture was of Cr/CrN/CrCN/TaN and the number of the layers were two, four and eight. Pin-on-disk wear test, hardness and surface roughness measurements were performed to characterize the tribological properties of the coatings. Results showed that as a result of coating process tribological properties of the alloy were improved significantly. It is observed that with increasing number of layer, wear strength, hardness and surface quality of the samples improved.

Özet

CoCrMo alaşımı, yüksek darbe ve yorulma dayanımı gibi özellikleri sayesinde ortopedik implant malzemesi olarak yaygın kullanılmaktadır. Bu alaşım yüksek korozyon dayanımı göstermesine rağmen düşük aşınma dayanımına sahiptir. Yapay eklem implant malzemesi olarak kullanıldığında, korozif vücut sıvısı nedeniyle düşük sürtünme özelliği ve düşük korozyon direnci göstermekte olup kısa sürelerde aşınmalara maruz kalmaktadırlar. Bu nedenle, CoCrMo alaşım yüzeyine korozyonu ve aşınma direncini geliştirmek için yüzey kaplama işlemi yapılmaktadır. Bu çalışmada CoCrMo alaşımının yüzeyinin tribolojik özelliklerini geliştirmek için kapalı alanda dengesiz magnetron püskürtme işlemi ile çok katmanlı kaplanmıştır. Kaplama mimarisi Cr/CrN/CrCN/TaN dizilimine sahip olup tabaka sayısı iki, dört ve sekizdir. Kaplamaların tribolojik özelliklerini karakterize etmek için disk üzerinde pin aşınma testi, sertlik ve yüzey pürüzlülüğü ölçümleri yapılmıştır. Sonuçlar, alaşımın tribolojik özelliklerinin önemli ölçüde arttığını göstermiştir. Tabaka sayısının artması ile örneklerin aşınma dayanımı, sertliği ve yüzey kalitesinin arttığı gözlenmiştir.

🔖

Cite This Article

BAHÇE, E., ASLAN, A. K., ÇAKIR, N., GÜLER, M. S. (2019). Investigation of the Surface Properties TaN Based Thin Film Coatings on the CoCrMo Alloy. Karadeniz Fen Bilimleri Dergisi, Cilt: 9 - Sayı: 2, 223–237. https://ajindex.com/articles/682655

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (12)

  1. Geetha,M., Singh, A.K., Asokamani R., Gogia, A.K., (2009). Ti based biomaterials, the ultimate choice for orthopaedic implants – A review, Progress in Materials Science,Vol. 54, 397–425.
  2. Chen, Q., Chen, P., Pang, X., Hu, Y., Zhang,Y., (2015). Adrenomedullin Up-regulates the Expression of Vascular Endothelial Growth Factor in Epithelial Ovarian Carcinoma Cells via JNK/AP-1 Pathway Int J Gynecol Cancer,Vol. 25, 1-6.
  3. Agarwal, R., García, A. J.,(2015). Biomaterial strategies for engineering implants for enhanced 2 osseointegration and bone repai, Advanced Drug Delivery Reviews, Vol. 94, 53-62.
  4. Güven, Ş.Y.(2014). Biyouyumluluk ve biyomalzemelerin seçimi”, Suleyman Demirel University Journal of Engineering Sciences and Design, Suleyman Demirel University Journal of Engineering Sciences and Design, Vol. 2(3), 303-311,
  5. Martinez-Nogues, V., Nesbitt, J.M., Wood, R.J.K., Cook, R.B,(2016). Nano-scale wear characterization of CoCrMo biomedical alloys, Tribology International, Vol. 93, 563-572.
  6. Affatato, S., & Grillini, L. (2013). Topography in bio-tribocorrosion. Bio-Tribocorrosion in Biomaterials and Medical Implants, 1–22a, UK: Woodhead Publishing Limited.Gottman I., Gutmanas E.Y., Hunter G. 2011. “Wear-Resistant Ceramic Films and Coatings”, Comprehensive Biomaterials, 1, Pages 127-155.
  7. Wang, Q., Zhang, L., Dong, J., (2010). Effects of Plasma Nitriding on Microstructure and Tribological Properties of CoCrMo Alloy Implant Material, Journal of Bionic Engineering, Vol. 7, 337-344.
  8. McEntire, B. J., Bal, B.S., Rahaman, M.N., Chevalier, J., Pezzotti,G.,(2015). Ceramics and ceramic coatings in orthopaedics, Journal of the European Ceramic Society,35, 4327-4369.
  9. Glewicz, A., Warcholinski, B., (2014). Tribological Properties of CrCN/CrN multilayer coatings, Tribology International,80,34-40.
  10. Holmberg, K., Matthews, A.,(2009).
  11. COATINGS TRIBOLOGY Properties, Mechanisms, Techniques and Applications in Surface Engineering (2. Baskı). UK: Elsevier. Wen,C., (2015). Surface Coating and Modification of Metallic Biomaterials (1. Baskı). UK: Woodhead Publishing. Griesser, H.J., (2016). Thin Film Coatings for Biomaterials and Biomedical Applications. (1.Baskı). UK: Woodhead Publishing. Zhang, T.F., Liu, B., Wu, B.J., Liu J., Sun, H., Leng, Y.X., Huang, X.,(2014). The stability of DLC film on nitrided CoCrMo alloy in phosphate buffer solution, Applied Surface Science, 308, 100–105.
  12. Di T., Mingjiang, D., Wenbin, F., L Songsheng, l., Chunbei, W., Mingchun, Z.,(2015). Performance of C