SavedAdd your journal

Journals / Düzce Üniversitesi Bilim ve Teknoloji Dergisi / 2022 / Cilt: 10 - Sayı: 3

Effects of TiN/CrN, CrAlN, and TiN Coatings on the Performance of AISI M2 Tool Steel

TiN/CrN, CrAlN ve TiN Kaplamaların AISI M2 Takım Çeliğinin Performansına Etkileri

Cemile KAYIŞ
Ege Anıl DİLER
Hatice SANDALLI
Fuat Can AĞARER
Pages
1344–1358
Publication Date
2022-07-31
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The wear performance of the CrAlN coating was higher at normal loads and sliding speeds while the tool life of the TiN/CrN-coated punch was better under impact loading conditions.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The aim of this study is to investigate the effects of various ceramic-based coatings on the performance of AISI M2 high-speed steel punch used in the nut piercing process.
📊
Key Findings & Data:AISI M2 punches were coated with TiN, TiN/CrN, and CrAlN utilizing a physical vapour deposition method.
💡
Conclusion & Impact:The wear performance of the CrAlN coating was higher at normal loads and sliding speeds while the tool life of the TiN/CrN-coated punch was better under impact loading conditions.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:AISI M2 takım çeliği · Delme zımbası · TiN/CrN

Abstract

The aim of this study is to investigate the effects of various ceramic-based coatings on the performance of AISI M2 high-speed steel punch used in the nut piercing process. AISI M2 punches were coated with TiN, TiN/CrN, and CrAlN utilizing a physical vapour deposition method. The total stroke number of the punches was used to evaluate the tool life of TiN, CrAlN, and TiN/CrN coated AISI M2 punches. AISI M2 punch coated with TiN/CrN was able to work up to greater stroke numbers than punches coated with TiN and CrAlN. Hardness and wear tests were performed to study the wear resistance of TiN/CrN and CrAlN coatings under relatively normal load conditions compared to actual working conditions (impact loading conditions) in the piercing process. The hardness and wear resistance of the CrAlN coating were greater than those of the TiN/CrN coating. The wear performance of the CrAlN coating was higher at normal loads and sliding speeds while the tool life of the TiN/CrN-coated punch was better under impact loading conditions.

Özet

Bu çalışmanın amacı, seramik esaslı çeşitli kaplama malzemelerinin, somun delme işlemlerinde kullanılan AISI M2 yüksek hız çeliğinden üretilmiş delme zımbalarının performanslarına etkilerinin araştırılmasıdır. AISI M2 zımbalar, fiziksel buhar biriktirme tekniği kullanılarak TiN, TiN/CrN ve CrAlN ile kaplanmıştır. Takım ömrünü belirlemek için TiN, TiN/CrN ve CrAlN ile kaplanmış AISI M2 zımbaların toplam strok sayıları dikkate alınmıştır. TiN/CrN kaplı AISI M2 zımba, TiN ve CrAlN kaplı zımbalara göre daha yüksek strok sayılarına kadar çalışabilmiştir. TiN/CrN ve CrAlN kaplamaların, delme işlemindeki gerçek çalışma koşullarına (darbeli yükleme koşulları) kıyasla normal yükleme koşulları altında aşınma direncini incelemek için sertlik ve aşınma testleri yapılmıştır. CrAlN kaplamanın sertlik ve aşınma direnci TiN/CrN kaplamadan daha yüksek olmuştur. Normal yükleme koşulları ve kayma hızlarında, CrAlN kaplamanın aşınma performansı daha yüksek iken darbeli yükleme koşullarında, TiN/CrN kaplama, takım ömrünün daha yüksek olmasını sağlamıştır.

🔖

Cite This Article

KAYIŞ, C., DİLER, E. A., SANDALLI, H., AĞARER, F. C. (2022). Effects of TiN/CrN, CrAlN, and TiN Coatings on the Performance of AISI M2 Tool Steel. Düzce Üniversitesi Bilim ve Teknoloji Dergisi, Cilt: 10 - Sayı: 3, 1344–1358. https://ajindex.com/articles/660865

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (12)

  1. H. Gong, X. Ding, J. Liu, and H. Feng, “Review of research on loosening of threaded fasteners,” Friction, in press, 2021,
  2. H. Gong, J. Liu and H. Feng, “Review on anti-loosening methods for threaded fasteners,” Chinese Journal of Aeronautics, in press, 2021,
  3. A. G. F. Araújo, M. Naeem, L. N. M. Araújo, T. H. C. Costa, K. H. Khan, J. C. Díaz-Guillén, J. Iqbal, M. S. Liborio and R. R. M. Sousa, “Design, manufacturing and plasma nitriding of AISI-M2 steel forming tool and its performance analysis,” Journal of Materials Research and Technology, vol. 9, no. 6, pp. 14517-14527, 2020
  4. V. Raja and T. Sornakumar, “Punch life improvement in cold forging of nut,” International Journal of Engineering Research & Technology (IJERT), vol. 3, no. 11, pp. 838-842, 2014
  5. L. H. P. Abreu, M. C. L. Pimentel, W. F. A. Borges, T. H. C. Costa, M. Naeem, J. Iqbal and R. R. M. Sousa, “Plasma nitriding of AISI M2 steel: performance evaluation in forming tools,” Surface Engineering, vol. 36, no. 5, pp. 508-515, 2020
  6. S. W. Choi, Y. S. Kim, Y. J. Yum and S. Y. Yang, “A study on strengthening mechanical properties of a punch mold for cutting by using an HWS powder material and a DED semi-AM method of metal 3D printing,” Journal of Manufacturing and Materials Processing, vol. 4, no. 4, pp. 1-16, 2020
  7. D. Kumar, H. S. Payal, and N. Beri, “Surface treatment of M2 tool steel: A review,” Asian Journal of Convergence in Technology, vol. 3, no. 3, pp. 1-10, 2017
  8. T. Weinhold, A. Dalke, A. Schramm and H. Biermann, “Sliding wear behavior of duplex coatings with different plasma nitride layers and a Cr‐Al‐Ti‐B‐N coating,” Engineering Reports, in press, 2021,
  9. F. Silva, R. Martinho, C. Martins, H. Lopes and R. Gouveia, “Machining GX2CrNiMoN26-7-4 DSS alloy: Wear analysis of TiAlN and TiCN/Al2O3/TiN coated carbide tools behavior in rough end milling operations,” Coatings, vol. 9, no. 6, pp. 1-21, 2019
  10. C. C. Wei, “Analyses of material properties of nitrided AISI M2 steel treated by plasma immersion ion implantation (PIII) process,” Advanced Science Letters, vol. 12, no. 1, pp. 148-154, 2012
  11. M. Skakov, B. Rakhadilov, and M. Sheffler, “Influence of electrolyte plasma treatment on structure, phase composition and microhardness of steel Р6М5,” Key Engineering Materials, vol. 531-532, no. 627–631, 2012
  12. M. Dubar, A. Dubois and L. Duba