Journals / Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi / 2017 / Cilt: 19 - Sayı: 56

CORRELATION BETWEEN EQUOTIP HARDNESS INDEX, MECHANICAL PROPERTIES AND DRILLABILITY OF ROCKS

KAYAÇLARIN EQUOTİP SERTLİK İNDEKSİ İLE MEKANİK ÖZELLİKLERİ VE DELİNEBİLİRLİĞİ ARASINDAKİ İLİŞKİLER

Pages
519–531
Publication Date
2017-05-01
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

Simple regression statistics revealed that Equotip hardness index test could be reliably used to predict the drillability of rocks that have a compressive strength higher than 19 MPa and a drilling rate index lower than 70

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Selection of a jumbo drill and appropriate bit type are important factors affecting machine performance and unit costs when excavating a mine roadway or tunnel.
📊
Key Findings & Data:The selection process can be optimized if the drillability, hardness and other mechanical properties of rocks are accurately measured.
💡
Conclusion & Impact:Simple regression statistics revealed that Equotip hardness index test could be reliably used to predict the drillability of rocks that have a compressive strength higher than 19 MPa and a drilling rate index lower than 70
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Equotip Sertlik İndeksi · Delme Oranı İndeksi · Delinebilirlik

Abstract

Selection of a jumbo drill and appropriate bit type are important factors affecting machine performance and unit costs when excavating a mine roadway or tunnel. The selection process can be optimized if the drillability, hardness and other mechanical properties of rocks are accurately measured. In this article, block samples collected at various locations around the world were initially prepared according to ISRM standards. Next, the Equotip hardness, Shore hardness, and mechanical properties were determined. In addition, the drilling rate index of the samples was measured and each sample was categorized based on its drillability. The relationship between Equotip hardness index, Shore index, drilling rate index, and other mechanical properties were analyzed. Simple regression statistics revealed that Equotip hardness index test could be reliably used to predict the drillability of rocks that have a compressive strength higher than 19 MPa and a drilling rate index lower than 70

Özet

Yeraltı maden galerileri veya tünel kazısı sırasında uygun delici makine ve uç seçimi, makine performansını ve birim maliyetleri etkileyen önemli faktörlerdir. Bu seçim kayacın delinebilirlik, sertlik ve diğer mekanik özelliklerinin doğru olarak ölçülmesiyle yapılabilir. Bu makalede, öncelikle yurt içi ve yurt dışından alınan blok numuneler ISRM standartlarına göre uygun boyutlarda hazırlanmıştır. Daha sonra, laboratuvarda Equotip ve Shore sertliği ile mekanik özellikleri belirlenmiştir. Ayrıca, her bir numunenin delinebilirliğini sınıflandırmak üzere delme oranı indeksi ölçülmüştür. Bu bağlamda Equotip sertlik indeksi ile Shore indeksi, mekanik özellikleri ve delme oranı indeksi arasındaki ilişkiler incelenmiştir. Basit regresyon analizlerinden dayanımı 19 MPa’ın üzerinde ve delme oranı indeksi 70’in altında olan kayaçlarda Equotip sertlik indeksinin delinebilirliğin tahmininde güvenilir olarak kullanılabileceği belirlenmiştir

🔖

Cite This Article

SU, O., MOMAYEZ, M. (2017). CORRELATION BETWEEN EQUOTIP HARDNESS INDEX, MECHANICAL PROPERTIES AND DRILLABILITY OF ROCKS. Dokuz Eylül Üniversitesi Mühendislik Fakültesi Fen ve Mühendislik Dergisi, Cilt: 19 - Sayı: 56, 519–531. https://ajindex.com/articles/659227

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (3)

  1. Altindag, R., Guney, A. 2005. Effect of the Specimen Size on the Determination of Consistent Shore Hardness Journal of Rock Mechanics and Mining Sciences, Cilt. 42, No. 1, s.153-160. 2004.08.002 International DOI:10.1016/j.ijrmms. [2] ISRM. 1978. Suggested Methods for Determining Abrasiveness of rocks, International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts, Cilt. 15, No. 3, s. 89-97. DOI: 10.1016/0148-9062(78)90002 -5 and [3] Su, O. 2003. Kömürün Dayanım ile Özellikleri Arasındaki İlişkilerin Araştırılması. Y. Lisans Tezi, Zonguldak Karaelmas Üniversitesi, Fen Bilimleri Enstitüsü, 100s, Zonguldak. Holmgeirsdottir, T., Thomas, PR. 1998. Use of the D-762 Shore Hardness Scleroscope for Testing Small Rock Volumes, International Journal of Rock Mechanics and Mining Sciences, Cilt. 35, s. 85–92. DOI:10.1016/S0148-9062(97)0031 7-3 ASTM E448-82. 2012. Standard Practice for Scleroscope Hardness Testing of Metallic Materials, 5 s. Altindag, R., Guney, A. 2006. ISRM Suggested Method for Determining the Shore Hardness Value for Rock, International Journal of Rock Mechanics and Mining Sciences, Cilt. 43, s. 19-22. DOI: 10.1016/j.ijrmms. 2005.04.004 ASTM D5873-05. 2012. Standard Test Method for Determination of Rock Hammer Method, 4 s. Rebound [8] Szlavin, J. 1974. Relationships between Some Physical Properties of Rock Determined by Laboratory Tests, International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts, Cilt. 12, No. 2, s.57-66. DOI: 10.1016/0148- 9062(74)92649-7
  2. Rabia, H., Brook, N. 1979.
  3. Shore Hardness of Rock, International Mining Sciences & Geomechanics Abstracts, Cilt. 16, s.335-336. DOI:10.1016/0148-9062(79)90245 -6 [10] Arthur, C.D. 1996. The Determination of Rock Material Properties Performance of Machine Excavation in Tunnels, Quarterly Journal of Engineering Geology, Cilt. 29, s. 67- 81.DOI:10.1144/GSL.QJEGH.1996.0 29.P1.05 the [11] Koncagül, E.C., Santi, P.M. 1999. Predicting Compressive Strength of the Breathitt Durability, Shore Hardness and Rock International Journal of Rock Mechanics and Mining Sciences, Cilt. 36, No. 2, s.139-153.DOI:10.1016/ S01489062(98)00174-0 Slake Structural Properties, [12] Altindag, R. 2002. Effects of Specimen Volume and Temperature on Hardness, Rock Mechanics and Rock Engineering, Cilt. 35, No. 2, s.109- 113. DOI: 10.1007/ s006030200014 [13] Yaşar, E., Erdoğan, Y. 2004. Estimation Physicomechanical Properties Using Hardness Methods, Engineering Geology, Cilt. 71, No.