Journals / Research on Engineering Structures and Materials / 2022 / Cilt: 8 - Sayı: 1

Effect of elevated temperature on strength and durability properties of concrete using nano-silica and alccofine

Pages
101–115
Publication Date
2022-10-19
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The microstructural analysis using scanning electron microscopy methods also reported that the porosity increased with increase in temperature.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The strength and durability properties of concrete using nano-silica and alccofine after exposed to higher temperatures were investigated in this study.
📊
Key Findings & Data:Concrete with 3% nano-silica and 15% alccofine were prepared and water cured for 28 days.
💡
Conclusion & Impact:The microstructural analysis using scanning electron microscopy methods also reported that the porosity increased with increase in temperature.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

The strength and durability properties of concrete using nano-silica and alccofine after exposed to higher temperatures were investigated in this study. Concrete with 3% nano-silica and 15% alccofine were prepared and water cured for 28 days. In an electric boogie furnace, concrete specimens with and without nano-silica and alccofine were heated to 400°C and 800°C for 4 hours. The specimens then were allowed to cool until they reached room temperature. The compressive strength test was used to determine strength, whereas the water absorption, porosity, and rapid chloride permeability tests were conducted to check durability properties. SEM images were used to examine the microstructure of concrete specimens at elevated temperatures. According to the test results, the strength and durability properties of concrete using nanosilica and alccofine deteriorated at high temperatures. At room temperature, concretes containing alccofine and nano silica performed better than control mixes. A severe loss in strength and a significant increase in charge pass, water absorption and porosity were observed at 800°C for concrete using alccofine and nano silica. The microstructural analysis using scanning electron microscopy methods also reported that the porosity increased with increase in temperature.

🔖

Cite This Article

K., A., P., S. R. (2022). Effect of elevated temperature on strength and durability properties of concrete using nano-silica and alccofine. Research on Engineering Structures and Materials, Cilt: 8 - Sayı: 1, 101–115. https://ajindex.com/articles/588815

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Nadeem A, Memon SA, Lo TY. The performance of Fly ash and Metakaolin concrete at elevated temperatures. Constr. Build. Mater, 2014; 62: 67–76.
  2. Memon SA, Shah SFA, Khushnood RA, Baloch WL. Durability of sustainable concrete subjected to elevated temperature–A review. Construction and Building Materials, 2019; 199: 435-455.
  3. Mohamedbhai GTG. Effect of Exposure Time and Rate of Heating and Cooling on Residual Strength of Heated Concrete. Magazine of Concrete Research, 1986; 38(136):151–158.
  4. Horszczaruk E, Sikora P, Cendrowski K, Mijowska E. The effect of elevated temperature on the properties of cement mortars containing nanosilica and heavyweight aggregates. Construction and Building Materials, 2017; 137: 420–431.
  5. Demirel B, Kelestemur O. Effect of elevated temperature on the mechanical properties of concrete produced with finely ground pumice and silica fume. Fire Safety Journal, 2010;45:385–391.
  6. Poon CS, Azhar S, Anson M, Wong YL. Strength and durability recovery of fire-damaged concrete after post-fire-curing, Cem. Concr. Res., 2001;31:1307–1318.
  7. Poon CS, Azhar S, Anson M, Wong YL. Performance of metakaolin concrete at elevated temperatures, Cem. Concr. Compos., 2003;25:83–89. https://doi.org/10.1016/S0958- 9465(01)00061-0 [8] Dündar B, Çınar E, Çalışkan AN. An investigation of high temperature effect on pumice aggregate light mortars with brick flour. Res. Eng. Struct. Mat, 2020; 6(3): 241-255.
  8. Fu YF, Wong YL, Tang CA, Poon CS. Thermal induced stress and associated cracking in cement-based composite at elevated temperatures - Part II: Thermal cracking around multiple inclusions, Cem. Concr. Compos., 2004;26(2):99-111.
  9. Poon CS, Azhar S, Anson M, Wong YL. Comparison of the strength and durability performance of normal-and high-strength pozzolanic concretes at elevated temperatures. Cement and concrete research, 2001;31(9):1291-1300.
  10. Khodja N, Hadjab H. Effects of Elevated Temperatures on Mechanical’s concrete specimen behaviour. In MATEC Web of Conferences, 2018;165: 22010. https://doi.org/10.1051/m