Journals / Politeknik Dergisi / 2018 / Cilt: 21 - Sayı: 2

The Physical Properties Of Aluminium-7xxx Series Alloys Produced By Powder Metallurgy Method

Toz Metalurjisi Yöntemiyle Üretilen Aluminyum-7xxx Serisi Alaşımlarının Fiziksel Özellikleri

Pages
341–350
Publication Date
2022-10-18
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The maximum Figure of merit value was determined as 18.71×10-2; on the Alumix-431-5 alloy at 96.904K

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Alumix-431 materialswere prepared by cold and warm compaction method applying 350-400 MPa pressures at RT (room temperature) 50 and 80°C temperatures.
📊
Key Findings & Data:The density measurements of materials were performed; the thermoelectric properties of materials were investigated at 5-300K under the He atmosphere, and the relationship between the measurements and sample properties was examined.
💡
Conclusion & Impact:The maximum Figure of merit value was determined as 18.71×10-2; on the Alumix-431-5 alloy at 96.904K
🔬Design:Research Article
📍Scope:1 samples
⚙️Variables:Domain Parameters

Abstract

Alumix-431 materialswere prepared by cold and warm compaction method applying 350-400 MPa pressures at RT (room temperature) 50 and 80°C temperatures. The density measurements of materials were performed; the thermoelectric properties of materials were investigated at 5-300K under the He atmosphere, and the relationship between the measurements and sample properties was examined. The measurements of thermoelectric properties showed that maximum resistivity [Alumix -431-1] and thermal conductivity [Alumix -431-6] values were obtained 0.161Ωm and 24.31W/Km, respectively at 285-295K temperature ranges and minimum electrical resistivity and thermal conductivity values were obtained on Alumix-431-6 and Alumix-431-1 samples, respectively. It was observed that Seebeck coefficient values varied mostly from negative sign to positive sign indicated dominate from carriers. The maximum Figure of merit value was determined as 18.71×10-2; on the Alumix-431-5 alloy at 96.904K

Özet

Alumix-431 malzemeleri; oda sıcaklığında (RT) ve 50,80°C sıcaklıklarında 350-400MPa basınç uygulayarak soğuk ve sıcak presleme yöntemiyle hazırlanmıştır. Malzemelerin yoğunluk ölçümleri yapılmıştır ve termoelektrik ölçümleri He atmosferi altında 5-300K sıcalık aralığında gerçekleştirilmiştir. Termoelektrik ölçümlerinde sonuçlar maksimum elektriksel öz direnç ve maksimum termal öz iletkenlik sırasıyla 285-295K sıcaklık aralığında Alumix-431-1 malzemesinde 0.161Ωm ve Alumix-431-6 malzemesinde 24.31W/Km olarak kaydedilmiştir. Minimum elektriksel öz direnç ve termal öz iletkenlik sırasıyla Alumix-431-6 ve Alumix-431- 1 malzemelerinde elde edilmiştir. Seebeck katsayısı taşıyıcıların yoğunluğuna bağlı olarak pozitif değerden negative değere değişim göstermiştir. Maksimum performans katsayısı Alumix-431-1 alaşımında 96.904K sıcaklığında 1.871×10 -2 olarak saptanmıştır.

🔖

Cite This Article

ACAR, A. N., EKŞİ, A. K., EKİCİBİL, A. (2022). The Physical Properties Of Aluminium-7xxx Series Alloys Produced By Powder Metallurgy Method. Politeknik Dergisi, Cilt: 21 - Sayı: 2, 341–350. https://ajindex.com/articles/588501

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (11)

  1. Rahman M.M., Nor S.S.M. and Rahman H.Y., Technical Report, ‘’Investigation on the effect of lubrication and forming parameters to the green compact generated from iron powder through warm forming route‘’, Materials and Design, 32: 447-452,(2011) Melúch L., ‘’Warm compaction of aluminum alloy alumix 123‘’, Thesis of Doctoral of Philosophy, University of Birmingham, page 237,(2009)
  2. Jafar-Salehi E., Ghasempoor A. and Eslamian M.,‘’Experimental study and predictive modelling of cold compaction green density in powder metallurgy of stainless steel components‘’, Powder Metallurgy, 56: 3, 208-215,(2013)
  3. Cao G., Zhang Q. and Brinker C.J., ‘’Annual review of nano research ’’ Volume 3, World Scientific Publishing, Singapore, page 568, (2010)
  4. Rahman M.M., Ariffin A.K., Nor S.S.M. and Rahman H.Y.,‘’Powder material parameters establishment through warm forming route‘’, Materials and Design 32: 264-271, (2011)
  5. Bhuiyan M.H., Kim T.-S. Koo J.M. and Hong S.-J., ‘’Microstructural behavior of the heat treated n-type 95% Bi 2 Te 3 –5% Bi 2 Se 3 gas atomized thermoelectric powders‘’, Journal of Alloys and Compounds 509: 1722–1728,(2011)
  6. Zevalkink A., Toberer E. S., Zeier W. G., Flage-Larsen E. and Snyder G.J.,‘’Ca 3 AlSb 3: An inexpensive, non- toxic thermoelectric material for waste heat recovery‘’, Energy Environ.Sci., 4: 510-518, (2011)
  7. Ohta H., Sugiura K. and Koumoto K., ‘’Recent Progress in Oxide Thermoelectric Materials: p-Type Ca 3 Co 4 O 9 and n-Type SrTiO 3 − ‘’Inorg. Chem.,47, 8429– 8436, (2008) Snyder G.-J. and Toberer E.S., ‘’Complex thermoelectric materials‘’, Nature Materials, vol.7.: 105-114,(2008)
  8. Fang S.F., Wang M.P. and Song M.,‘’An approach for the aging process optimization of Al–Zn–Mg–Cu series alloys‘’. Materials and Design, vol. 30:2460-246, (2009)
  9. Jia Y., Cao F., Ning Z., Guo S., Ma P. and Sun J., ‘’Influence of second phases on mechanical properties of spray deposited Al–Zn–Mg–Cu alloy‘’. Materials and Design, vol. 40: 536-540, (2012)
  10. Liu Y., Jiang D., Li B., Yang W. and Hu J., ‘’Effect of cooling aging on microstructure and mechanical properties of an Al–Zn–Mg–Cu alloy‘’, Materials and Design, vol. 57: 79-86, (2014) Ekşi A.,Veltl G., Petzoldt F., Lipp K. and Sonsino C.M., ‘’ Tensile and fatigue properties of cold and warm compacted alumix 431 alloy‘’, Powder Metallurgy, 200A, vol 47, no.1: 60-64, (2004)
  11. Feng W., Baiqing X., Yongan Z., Hongwei L., and Xiaoqing H. ‘’ Microstructural development of spray deposited Al-Zn-Mg-Cu alloy during subsequent por