Journals / Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi / 2020 / Cilt: 26 - Sayı: 5

Design and manufacturing of 15 DOF myoelectric controlled prosthetic hand

15 serbeslik dereceli myoelektriksel kontrollü proztez elin tasarımı ve imalatı

Pages
884–892
Publication Date
2022-10-18
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The prosthetic hand's total cost is US$ 450.The hand was compared in terms of qualitative and quantitativeperformance metrics with other high-priced rivals and the findingswere interpreted.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:This study's main purpose is to manufacture a low-cost, highlyfunctional, myoelectric signal-controlled prosthetic hand for amputeesin developing countries below a certain economic level.
📊
Key Findings & Data:In this study, aprosthetic hand with five fingers was modeled on 15-degree freedom,and an independent joint movement was achieved through the use of aseparate motor actuator for each joint in the fingers.
💡
Conclusion & Impact:The prosthetic hand's total cost is US$ 450.The hand was compared in terms of qualitative and quantitativeperformance metrics with other high-priced rivals and the findingswere interpreted.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

This study's main purpose is to manufacture a low-cost, highlyfunctional, myoelectric signal-controlled prosthetic hand for amputeesin developing countries below a certain economic level. In this study, aprosthetic hand with five fingers was modeled on 15-degree freedom,and an independent joint movement was achieved through the use of aseparate motor actuator for each joint in the fingers. The hand of theprosthetic can therefore keep the objects in the best possible way. Theprosthetic was produced by hand using PLA material on a 3D printer toreduce cost. Bioelectric signals provide the human-prosthetic handinteraction, i.e. identification of the form of hand gesture. With 97percent progress, the classification of a human hand with the SVMalgorithm has been achieved. The prosthetic hand's total cost is US$ 450.The hand was compared in terms of qualitative and quantitativeperformance metrics with other high-priced rivals and the findingswere interpreted.

Özet

Bu çalışmanın temel amacı, belirli bir ekonomik düzeyin altındaki gelişmekte olan ülkelerdeki ampute'ler için düşük maliyetli, oldukça işlevsel, miyoelektrik sinyal kontrollü bir protez el üretmektir. Bu çalışmada, beş parmaklı protez el 15 serbestlik dereceli olarak modellenmiş ve parmaklardaki her bir eklem için ayrı bir motor aktüatörü kullanılarak bağımsız eklem hareketi sağlanmıştır. Protezin el bu nedenle nesneleri mümkün olan en iyi şekilde tutabilir. Protez, maliyeti azaltmak için bir 3D yazıcıda PLA malzemesi kullanılarak üretildi. Biyoelektrik sinyaller insan protezi el etkileşimini, yani el hareketi formunun tanımlanmasını sağlar. Yüzde 97 başarı ile bir insan elinin hareket türü tanımlaması SVM algoritması ile sağlandı. Protez elin toplam maliyeti 450 ABD dolarıdır. El, diğer yüksek fiyatlı rakiplerle kalitatif ve kantitatif performans metrikleri açısından karşılaştırılmış ve bulgular yorumlanmıştır.

🔖

Cite This Article

GÜLTEN, A., YAKUT, O., TAŞAR, B. (2022). Design and manufacturing of 15 DOF myoelectric controlled prosthetic hand. Pamukkale Üniversitesi Mühendislik Bilimleri Dergisi, Cilt: 26 - Sayı: 5, 884–892. https://ajindex.com/articles/587399

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. World Health Organization.“World Report on Disability”. New York, NY: World Health Organization, 2011. https://www.who.int/disabilities/world_report/2011/r eport.pdf (24.09.2019)
  2. Hamner SR, Narayan VG, Donaldson, KM. “Designing for scale: Development of the remotion knee for global emerging markets”. Annals of Biomedical Engineering, 41(9), 1851-1859, 2013
  3. Borne A, Porter A, Recicar J, Maxson, T and Montgomery C. “Pediatric Traumatic Amputations in the United States”. Journal of Pediatric Orthopaedics, 37(2), 104-107, 2017
  4. Strait E. “Prosthetics in Developing Countries.” http://www.oandp.org/publications/resident/pdf/Devel opingCountries.pdf. (25.05.2010)
  5. Smith M. “Engadget-new bebionic hand almost doubles its grip-strength, steered by users’ electrical skin signals”. http://www.engadget.com/2012/09/07/bebionic-3- bionic-hand/ (24.09.2019)
  6. Webster G. “The bionic hand with the human touch”. https://edition.cnn.com/2013/02/01/tech/bionic-handilimb-prosthetic/index.html. (24.09.2019)
  7. Lightbody S. “Design of an Articulated Thumb for a LowCost Prosthetic Hand”. Department of Engineering, Sweet Briar College, Lecturer Notes, Virginia, ABD
  8. Marrero IC. “Hand Anatomy”. http://emedicene.medscape.com/article/1285060- overview. (01.01.2010)
  9. Cipriani C, Controzzi M, and Carrozza, MC. “Objectives, criteria and methods for the design of the SmartHand transradial prosthesis”. Robotica, 28(6), 919-927, 2010
  10. Slade P, Akhtar A, Nguyen, M, Bretl, T. “Tact: Design and Performance of an Open-Source, Affordable, Myoelectric Prosthetic Hand”. 2015 IEEE International Conference on Robotics and Automation (ICRA), Washington State Convention Center, Seattle, Washington, May 26-30, 2015
  11. Stratasys Direct Manufacturing. “3D Printing Materials: Choosing the Right Material for Your Application”. https://docplayer.net/22763790-3d-printing-advancedmanufacturing-3d-printing-materials-choosing-the-rightmaterial-for-your-application-stratasysdirect-com.html, (24.09.2019)
  12. Mcor Technologies, “How Paper-Based 3D Printing Works”. http://www.samhirota.com/uploads/8/3/4/4/8344944 /mcor-wpeu-06092013_low.pdf (24.09.2019)
  13. Zhao Z. and Laperrière, L. “Adaptive Direct Slicing of the Solid Model for Rapid Prototyping”. International Journal of Production Research, 38(1), 69-83, 2000
  14. Parasa V, Gopichand A, Shankar NVS, Rao KR. “Fabrication of low cost prosthetic arm with foamed fingers”. International Journal of Engineering Research