Journals / Mühendislik Bilimleri ve Tasarım Dergisi / 2018 / Cilt: 6 - Sayı: 4

THE EFFECT OF PROCESS CONDITIONS ON THE PRODUCTION OF INDUSTRIAL SİALON-TİN CUTTING TOOLS

ENDÜSTRİYEL SİALON-TİN KESİCİ UÇ ÜRETİMİNDE PROSES KOŞULLARININ ETKİSİ

Pages
716–724
Publication Date
2022-10-19
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The optimization efforts in the production process of SiAlON-TiN cutting tools with the desired properties have been achieved in a pilot scale.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:Super alloys are widely used in the field of aviation and they are difficult to machine.
📊
Key Findings & Data:Since SiAlON based ceramic cutting tools can be produced with gas pressure sintering method which is suitable for serial production, they provide cost advantages over Al2O3-SiCw cutting tools.
💡
Conclusion & Impact:The optimization efforts in the production process of SiAlON-TiN cutting tools with the desired properties have been achieved in a pilot scale.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Kesici Uç · SiAlON-TiN Kompozit · Proses

Abstract

Super alloys are widely used in the field of aviation and they are difficult to machine. Alumina and silicon nitride based ceramic matrix composites have been used for super alloy machining. Since SiAlON based ceramic cutting tools can be produced with gas pressure sintering method which is suitable for serial production, they provide cost advantages over Al2O3-SiCw cutting tools. However SiAlON ceramics have the disadvantage for super alloy machining due to inadequate properties in respect of chemical durability. Therefore in this study in order to enhance chemical durability of SiAlON ceramics, SiAlON based ceramics prepared with unique compositional design with TiN incorporation. SiAlON-TiN composites were prepared in pilot scale which allows description of the problems and their solutions. The optimization efforts in the production process of SiAlON-TiN cutting tools with the desired properties have been achieved in a pilot scale.

Özet

Süperalaşımlar havacılık alanında yaygın olarak kullanılan ve işlenmesi zor malzemelerdir. Alümina ve silisyum nitrür esaslı seramik matrisli kompozitler süperalaşımların işlenmesinde kullanılmaktadırlar. SiAlON esaslı seramik kesici uçlar seri üretime uygun gaz basınçlı sinterleme tekniği ile üretilebildikleri için Al2O3-SiCw kesici uçlara karşı maliyet avantajı sağlamaktadırlar. Ancak SiAlON seramikleri kimyasal dayanım açısından süperalaşım işlenmesinde yeterli değildir. Bu nedenle bu çalışmada SiAlON seramiklerinin kimyasal dayanımını arttırmak için TiN ilavesi yapılarak özgün komposizyon tasarımlarıyla hazırlanmış SiAlON-TiN kompozitlerinin pilot ölçekte üretimi yapılarak, üretim esnasında karşılaşılan sorunlar ve çözüm önerileri açıklanmıştır. Üretim sürecinde yapılan optimizasyon çalışmaları neticesinde istenen özelliklerde kesici uç üretimi pilot ölçekte başarılmıştır.

🔖

Cite This Article

KARA, F., AÇIKBAŞ, N. Ç. (2022). THE EFFECT OF PROCESS CONDITIONS ON THE PRODUCTION OF INDUSTRIAL SİALON-TİN CUTTING TOOLS. Mühendislik Bilimleri ve Tasarım Dergisi, Cilt: 6 - Sayı: 4, 716–724. https://ajindex.com/articles/583725

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (10)

  1. Acikbas, N. C., Kumar, R., Kara, F., Mandal, H., and Basu, B., 2011. Influence of β-Si3N4 particle size and heat treatment on microstructural evolution of αı:βı-SiAlON ceramics, Journal of the European Ceramic Society, 31(4), 629-635.
  2. Acikbas, N.C., Kara, F., 2017. The effect of z value on intergranular phase crystallization of αı/βı-SiAlON-TiN composites. Journal of the European Ceramic Society,37(3), 923-930.
  3. Acikbas, N.C., Demir, O., 2013. The effect of cation type, intergranular phase amount and cation mole ratios on z value and intergranular phase crystallization of SiAlON ceramics. Ceramics International,39(3), 3249-59.
  4. Acikbas, N.C., Tegmen, S., Ozcan, S, Acikbas, G., 2014. Thermal shock behaviour of α:β-SiAlON–TiN composites. Ceramics International, 40(2), 3611-8. Acikbas NC. 2018. Tribological Behaviour of SiAlON-TiN Composites, Journal of the European Ceramic Society, DOI:10.1016/j.jeurceramsoc.2018.01.013 Ayas, E, Kara, A, Mandal, H, Turan, S, Kara, F., 2004. Production of alpha-beta SiAlON-TiN/TiCN composites by gas pressure sintering. Silicate Industries, 69(7), 287-92.Bitterlich, B, Bitsch, S, Friederich, K., 2008. SiAlON based ceramic cutting tools. Journal of the European Ceramic Society,28(5), 989-94.
  5. Blugan, G., Hadad, M., Janczak‐Rusch, J., Kuebler, J., Graule, T., 2005. Fractography, mechanical properties, and microstructure of commercial silicon nitride–titanium nitride composites, Journal of the American Ceramic Society, 88(4), 926-33. G. Brandt, 1999. Wear and Thermal Shock Resistant SiAlON Cutting Tool Material, U.S. Patent No. 5,965,471. Bowen, P., Highfield, J.G., Mocellin, A., Ring, T. A., 1990. Degradation of Aluminium Nitride Powder in an Aqueous Environment, Journal of the American Ceramic Society, 73, 724-728.
  6. Desmaison, J, Desmaison, M., 1999. Boride/nitride composites: synthesis and properties. In Materials Science of Carbides, Nitrides and Borides (pp. 267-284).
  7. Springer Netherlands. Evans, A.G. and Charles, E.A., 1976. Fracture toughness determinations by indentation, Journal of the American Ceramic Society, 59, 371–372.
  8. Graziani, T.B., Bellosi, A.B. 1995. Densification and characteristics of TiN ceramics. Journal of Materials Science, 14(15), 1078-81.
  9. Kocjan, A., Krnel, K., Kosmač, T., 2008. The influence of temperature and time on the AlN powder hydrolysis reaction products, Journal of the European Ceramic Society, 28(5), 1003-8.
  10. Krnel, K., Kosmac̆, T., 2001. Protection of AlN powder against hydrolysis using aluminum d