SavedAdd your journal

Journals / Isı Bilimi ve Tekniği Dergisi / 2012 / Cilt: 32 - Sayı: 2

Kanatlı borulu evaporatörün kuru şartlar altında ısıl performansının incelenmesi

Investigation of thermal performance of finned tube evaporator under dry conditions

Dilek Nur ÖZEN
Kemal ALTINIŞIK
Pages
145–150
Publication Date
2022-10-18
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

A numerical model was developed in order to calculate the overall thermal permeability (UA) in transient regime.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:In this study, analysis of thermal performance of finned tube evaporator under dry conditions has numerically been done.
📊
Key Findings & Data:The numerical model was solved by using Matlab R2010 program.
💡
Conclusion & Impact:A numerical model was developed in order to calculate the overall thermal permeability (UA) in transient regime.
🔬Design:Modeling & Simulation
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

In this study, analysis of thermal performance of finned tube evaporator under dry conditions has numerically been done. The heat convection coefficient in air and refrigerant sides were calculated by considering their varying properties. In addition, the surface temperature of fin and tubes along the fin were calculated. A numerical model was developed in order to calculate the overall thermal permeability (UA) in transient regime. The numerical model was solved by using Matlab R2010 program. The overall thermal permeability (UA) was examined under different air inlet temperatures and air velocity. In addition, variation of the convection heat transfer coefficient with respect to quality at the refrigerant side was examined.

Özet

Bu çalışmada kanatlı borulu bir evaporatörün ısıl performansının analizi kuru şartlar için sayısal olarak yapılmıştır. Havanın ve soğutucu akışkanın değişen özelliklerine göre hava ve soğutucu akışkan tarafındaki taşınım katsayısı hesaplanmıştır. Ayrıca kanat boyunca yüzey sıcaklıkları ve boru yüzey sıcaklıkları hesaplanmıştır. Geçici rejimde evaporatörün toplam ısıl geçirgenliğini (UA) hesaplamak için bir sayısal model oluşturulmuş ve sayısal model Matlab R2010 bilgisayar programında çözülmüştür. Toplam ısıl geçirgenliği, havanın farklı giriş sıcaklıkları ve hızlarında incelenmiştir.Ayrıca kuruluk derecesine göre soğutucu akışkan tarafındaki taşınım katsayısının değişimi incelenmiştir.

🔖

Cite This Article

ÖZEN, D. N., ALTINIŞIK, K. (2022). Kanatlı borulu evaporatörün kuru şartlar altında ısıl performansının incelenmesi. Isı Bilimi ve Tekniği Dergisi, Cilt: 32 - Sayı: 2, 145–150. https://ajindex.com/articles/542553

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (14)

  1. Domanski, P. A., Yashar, D. and Kim, M,.Performance of a finned-tube evaporator optimized for different refrigerants and its effect on system efficiency, Int. J. Refrigeration, 28, 820-827, 2005
  2. Greco. A. And G.P. Vanoli, Flow- boiling of R22, R134a, R507, R404A and R410A inside a smooth horizantal tube, Int. J. Refrigeration, 28, 872-880, 2005.
  3. Jabardo, J.M. S. and Filho,E.P.B, Convective boiling of halocarbon refrigerants flowing in a horizontal copper tube an experimental study, Exp Therm Fluid Sci, 23, 93-104, 2000.
  4. Jung, D., Cho, Y. and Park,K., Flow condensation heat transfer coefficients of R22, R134a, R407C, and R410A inside plain and microfin tubes, Int J Refrigeration, 27, 25-32, 2004.
  5. Kakaç, Soğutma ve Havalandırma Sistemleri için Evapotatörler ve Yoğuşturucular ve Isı Tasarımları, III. Uluslar arası Yapıda Tesisat Bilim ve Teknoloji Sempozyumu, 1998.
  6. Lenic, K., Trp, A. and Frankovic, B., Prediction of an effective cooling output of the fin-and tube heat exchanger under frosting conditions, Applied Thermal Engineering,2009.
  7. McQuiston, F.C., Heat mass and momentum transfer data for five plate-fin tube transfer surface,ASHRAE Transactions, Vol. 84, no. 1, pp. 266-293, 1978.
  8. McQuiston, F.C, Correlation of heat, mass and momentum transport coefficients for plate-fintube heat transfer surfaces with staggered tubes, ASHRAE Transactions, Vol. 84, no. 1, pp. 294-309, 1978.
  9. Mirth, D.R. and Ramadhyani, S., Prediction of coolingcoils performance under condensing conditions, International Journal Heat and Fluid Flow, Vol. 14, pp. 391-400, 1993.
  10. Mirth, D.R. and Ramadhyani, S., Correlations for predicting the air-side Nusselt numbers and friction factors in chilled-water cooling coils, Experimental Heat Transfer, Vol. 7, pp. 143-162 1994.
  11. Pirompugd, W., Wongwises, S. and Wang, C.C., A tube-by-tube reduction method for simultaneous heat and mass transfer characteristics for plain fin-and-tube heat exchangers in dehumidifying conditions, Heat and Mass Transfer, Vol. 40, pp. 756-765, 2005.
  12. Pirompugd, W., Wongwises, S. and Wang, C.C., Simultaneous heat and mass transfer characteristics for wavy fin-and-tube heat exchangers under dehumidifying conditions, Int. J. of Heat and Mass Transfer Vol. 49, pp. 132-143, 2006
  13. Seker, D., H. Kartaş and Eğrican, N., Frost formation on fin-and-tube heat exchangers. Part I-Modeling of frost formation on fin-and tube heat exchangers, Int. J. Refrigerat., 27 367–374, 2004.
  14. Şeker, D., Kartaş and H., Eğrican, N., Frost formation