Journals / Fırat Üniversitesi Fen ve Mühendislik Bilimleri Dergisi / 2006 / Cilt: 18 - Sayı: 2

Characterization of Fe-Cr-C coatings used TIG method

TIG metodu kullanılarak yapılan Fe-Cr-C kaplamalarının karakterizasyonu

Pages
267–270
Publication Date
2022-10-17
DOI
—
🏛️Bibliographic metadata and full text access for this article are provided via DergiPark.
DergiPark Record ↗
✨

AI Summary & Key Takeaways

AI Insight
⚡ TL;DR(Too Long; Didn't Read)

The hardness values of $M_7C_3$ carbides varied between 1050-1500 HV, while the hardness of $M_7C_3+austenite(gamma)$ matrix was measured between 500-750 HV.

📌 3 Key Takeaways

🎯
Objective & Hypothesis:The microstructure of Fe-Cr-C coatings was experimentally investigated.
📊
Key Findings & Data:The coatings were formed by means of a gas tungsten arc torch on the AISI 4340 steel.
💡
Conclusion & Impact:The hardness values of $M_7C_3$ carbides varied between 1050-1500 HV, while the hardness of $M_7C_3+austenite(gamma)$ matrix was measured between 500-750 HV.
🔬Design:Research Article
📍Scope:Comprehensive Sample
⚙️Variables:Domain Parameters

Abstract

The microstructure of Fe-Cr-C coatings was experimentally investigated. The coatings were formed by means of a gas tungsten arc torch on the AISI 4340 steel. The microstructures of the coatings are found to composed of primary $M_7C_3$ carbides in eutectic of austenite matrix. The hypereutectic microstructure consisted of $M_7C_3$ and $M_7C_3+austenite(gamma)$. The hardness values of $M_7C_3$ carbides varied between 1050-1500 HV, while the hardness of $M_7C_3+austenite(gamma)$ matrix was measured between 500-750 HV.

Özet

Fe-Cr-C kaplamalarının mikroyapısı deneysel olarak incelendi. Kaplamalar, AISI 4340 çelik yüzeyinde bir gaz tungsten ark torcu vasıtasıyla oluşturuldu. Kaplama mikroyapılarında ostenit matrisi içinde katılaşmış ve dağılmış $(Cr,Fe)_7C_3$ karbürleri tespit edildi. $(Cr,Fe)_7C_3$ karbürleri ile $(Cr,Fe)_7C_3+(gamma)$ içeren mikroyapılar ötektik üstü mikroyapılardır. $(Cr,Fe)_7C_3$ karbürlerinin sertlik değerleri 1500 HV iken $(Cr,Fe)_7C_3+(gamma)$ matrisin sertlik değerleri 750 HV olarak tespit edildi.

🔖

Cite This Article

BUYTOZ, S., YILDIRIM, M. M., EREN, H. (2022). Characterization of Fe-Cr-C coatings used TIG method. Fırat Üniversitesi Fen ve Mühendislik Bilimleri Dergisi, Cilt: 18 - Sayı: 2, 267–270. https://ajindex.com/articles/513559

📄 Full Text PDF Viewer

📄

PDF görüntüleyici hazırlanıyor...

References (1)

  1. Svensson, L.-E., Gretoft, B., Ulander, B., Bhadeshia, H.K.D.H. (1986). Fe-Cr-C hardfacing alloys for high-temperature applications. Journal of Materials Science, 21, 1015-1019 2. Atamert, S., Bhadeshia, H.K.D.H. (1990). Microstructure and stability of Fe-Cr-C hardfacing alloys. Materials Science and Engineering A, 130, 101-111 3. Liu, H.-N., Sakamoto, M., Nomura, M., Ogi, K. (2001). Abrasion resistance of high Cr cast irons at an elevated temperature. Wear, 250, 71-75 4. Wu, X., Chen, G. (1999). Nonequilibrium microstructures and their evolution in a Fe-Cr-W-Ni-C laser clad coating. Materials Science and Engineering A, 270, 183-189 5. Durgutlu, A. (2004). Experimental investigation of the effect of hydrogen in argon as a shielding gas on TIG welding of austenitic stainless steel. Materials and Design, 25, 19-23 6. Tusek, J., Suban, M. (2000). Experimental research of the effect of hydrogen in argon as a shielding gas in arc welding of high-alloy stainless steel. Int J Hydrogen Energy, 25, 369-376 7. Buytoz, S. Yildirim, M.M. Eren, H. (2005). Microstructural and microhardness characteristics of gas tungsten arc synthesized Fe-Cr-C coating on AISI 4340. Materials Letters, 59, 607-614 8. Buytoz, S. (2006). Microstructural properties of $M_7C_3$ eutectic carbides in a Fe-Cr-C alloy. Materials Letters, 60, 605-608 9. X. Wu. (1999). Rapidly solidified nonequilibrium microstructure and phase transformation of laser-synthesized iron-based alloy coating, Surface and Coatings Technology 115, 153-162 10. Robson, J.D. (1996). Modelling of carbide and laves phase precipitation in 9-12 wt% choromium steels. Ph.D. Thesis, 79, UK 11. Wang, S.-H., Chen, J.-Y., Xue, L. (2005). A study of the abrasive wear behaviour of laser-clad tool steel coatings. Surface and Coating Technology, basımda. 12. Sexton, L., Lavin, S., Byrne, G., Kennedy, A. (2002). Laser cladding of aerospace materials. Journal of Materials Processing Technology, 122, 63-68 13. Buytoz, S. (2004). AISI 4340 çeliğinin nitrürasyon ve GTA kaynak yöntemi ile yüzey modifikasyonu işlemleri sonrası mekaniksel davranışlarının araştırılması. Doktora tezi, Fırat Üniversitesi, 733, Elazığ/Türkiye. 14. Buytoz, S. Yildirim, M.M. Investigation of abrasive wear performance of high-chromium ferrochromium carbon coatings. Materials Characterization (incelemede)